ETHAN ALLEN 093699 Zoe Eight-Light Nickel Chandelier Instruction Manual
- June 12, 2024
- ETHAN ALLEN
Table of Contents
ETHAN ALLEN 093699 Zoe Eight-Light Nickel Chandelier
Product Information
Product Name: ZOE 8 Light Chandelier
Model Numbers: 093699, 093702
Safety Instructions
- These instructions are provided for your safety. It is very important that they are read completely before beginning the installation of your fixture.
- We strongly recommend installation by a licensed electrician.
- Turn off the power at the switch before replacing the bulbs, making sure the fixture has had sufficient time to cool down.
- Do not subject the fixture to any shock while lit as shattering of bulbs may result.
Assembly Instructions
-
Shut off the main electrical supply at fuse box / circuit breaker.
-
Remove all parts from carton. Do not throw away any parts.
-
Thread tube (T) onto the threaded nipple above the box (S).
-
Lift shade (M) over bottom section of fixture through the canopy (F) and tubes. Slide split washer (R) between shade washer (P) and shade washer (Q). Secure position of shade (M) by turning shade washer (P) clockwise until it rests firmly against split washer (R).
-
Remove mounting bar (B) with tube (D) and loop (E) attached from canopy (F) by loosening collar (G).
-
Affix mounting plate (B) to ceiling outlet box with mounting plate screws (C) provided.
-
Measure desired drop for fixture to hang and add/remove extension tubes (I)/(J)/(K)/(T) as needed. Guide wiring through extension tubes before threading tubes together. To add/remove extensions: (Un)Thread the threaded nipple of one extension into the threaded opening of the next extension. Make sure wiring is pulled tight when threading extensions together to prevent damage to the wire.
-
Guide wiring through top tube (H) and hook (U), collar (G), canopy (F), and loop (E) and tube (D).
-
Make proper electrical connections as described in steps 10-12. A licensed electrician is recommended.
-
Attach ground wire from fixture (green or silver in color) to
ground wire from outlet box. Fasten wires together with wire nut (A) and tightly wrap the connection with electrical tape. -
Attach hot wire from fixture (black in color or smooth side of wire) to hot wire from outlet box. Fasten wires together with wire nut (A) and tightly wrap connection with electrical tape.
-
Attach neutral wire from fixture (white in color or ribbed side of wire) to neutral wire from outlet box. Fasten wires together with wire nut (A) and tightly wrap connection with electrical tape.
-
Carefully push wire connections back into ceiling outlet box.
-
Lift canopy (F) to ceiling outlet box and secure with collar (G).
-
Connect hook (U) to loop (E).
-
Install proper bulbs into sockets (N).
Troubleshooting If you need to replace the tube:
- Remove the shade out of the lamp by loosening the lock ring (m).
- Take down the whole lamp.
- Remove the canopy and all tubes and pull the cord out.
- Unscrew the tube with the lock rings on and pull the cord out of this tube too.
- Wire the cord through the replaced tube and lock rings and thread this tube into the nipple.
- Wire the cord through the tubes and canopy in sequence and reassemble the lamp to ceiling.
Care Instructions To clean, use a soft cloth only. Do not use any chemical or abrasive cleaners.
IMPORTANT SAFETY INSTRUCTIONS:
- These instructions are provided for your safety. It is very important that they are read completely before beginning the installation of your fixture.
WE STRONGLY RECOMMEND INSTALLATION BY A LICENSED ELECTRICIAN.
- Turn off power at switch before replacing bulbs, making sure fixture has had sufficient time to cool down.
- DO NOT subject the fixture to any shock while lit as shattering of bulbs may result
ASSEMBLY INSTRUCTIONS
- SHUT OFF THE MAIN ELECTRICAL SUPPLY AT FUSE BOX / CIRCUIT BREAKER.
- Remove all parts from the carton. Do not throw away any parts.
- Thread tube (T) onto the threaded nipple above the box (S)
- Lift shade (M) over the bottom section of the fixture through the canopy(F) and tubes. Slide split washer (R) between shade washer (P) and shade washer (Q).Secure the position of shade (M) by turning the shade washer (P) clockwise until it rests firmly against the split washer (R).
- Remove mounting bar (B) with tube(D) and loop (E) attached from the canopy (F) by losing collar(G).
- Affix mounting plate (B) to ceiling outlet box with mounting plate screws (C) provided.
- Measure the desired drop for the fixture to hang and add/remove extension tubes (I)/(J)/(K)/(T) as needed. Guide wiring through extension tubes before threading tubes together. TO ADD/REMOVE EXTENSIONS: (Un)Thread the threaded nipple of one extension into the threaded opening of the next extension. Make sure the wiring is pulled tight when threading extensions together to prevent damage to the wire
- Guide wiring through top tube(H) and hook(U), collar(G), canopy(F) and loop(E), and tube(D).
- Make proper electrical connections described in steps 10-12. A LICENSED ELECTRICIAN IS RECOMMENDED.
- Attach the ground wire from the fixture (green or silver in color) to the ground wire from the outlet box. Fasten wires together with wire nut (A) and tightly wrap the connection with electrical tape.
- Attach hot wire from fixture (black in color or smooth side of wire) to hot wire from outlet box. Fasten wires together with wire nut (A) and tightly wrap the connection with electrical tape.
- Attach neutral wire from fixture (white in color or ribbed side of wire) to neutral wire from outlet box. Fasten wires together with wire nut (A) and tightly wrap the connection with electrical tape.
- Carefully push wire connections back into the ceiling outlet box.
- Lift canopy (F) to the ceiling outlet box and secure with collar(G).
- Connect hook (U) to loop (E).
- Install proper bulbs into sockets (N).
To clean, use a soft cloth only. Do not use any chemical or abrasive cleaners .
- Remove the shade of the lamp by losing the lock ring (m)
- Take down the whole lamp
- Remove the canopy and all tubes and pull the cord out
- Unscrew the tube with the lock rings on and pull the cord out of this tube too
- Wire the cord through the replaced tube and lock rings and thread this tube into the nipple
- Wire the cord through the tubes and canopy in sequence and reassemble the lamp to the ceiling.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>