LIGHTWARE HDMI-TPS-TX87 Twisted Pair HDBaseT Extender User Guide
- June 12, 2024
- LIGHTWARE
Table of Contents
HDMI-TPS-TX87 Twisted Pair HBase Extender
User Guide
Quick Start Guide
HDMI-TPS-TX87
HDMI-TPS-RX87
HDMI-TPS-TX87 Twisted Pair HBase Extender
The transmitter and the receiver have the same construction and connectors.
The product is compatible with any HDBaseT TM third-party devices. HDBaseT TM
and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.
Front And Rear View – Legend
-
RS-232 port Local RS-232 port for bidirectional serial data connection and performing firmware upgrade (programming).
-
RS-232 switch Normal: serial data is passed through the device.
Prog: RS-232 pass-through function is disabled, the device is ready for the firmware upgrade (see the figure below). -
Status LEDs See the next section.
-
TPS mode switch
LR: Lon reach TPS mode; lower resolution (max 1080p), longer distances;
Auto: TPS mode is determined automatically. -
IR mode switch IR output signal modulation switch; the 38 kHz modulation can be switched On (Emitter position) or Off (Wired position).
-
IR input IR signal input connector (for 3.5 mm Jack, 3-pole, TRS plug).
-
IR output IR signal output connector (for 3.5 mm Jack, 2-pole, TS plug).
-
DC input 12V DC input for local power supply.
-
TPS port TPS port to the other compatible device (extender / matrix / board).
-
HDMI port Video port for DVI or HDMI signal.
Status LEDs
HDCP
| OFF| Video output signal is not encrypted with HDCP.
| ON| Video output signal is encrypted with HDCP.
SIGNAL
| OFF| No video signal transmission.
| ON| Video signal transmission.
LINK
| OFF| TPS connection failed between the devices.
| BLINKING| TPS connection is detected and LPPF link mode is active.
| ON| TPS connection is detected and HDBT or LR link mode is active.
LIVE
| OFF| No power supply or out of order.
| BLINKING| Device is powered and ready to use.
Important Safety Instructions
Please read the supplied safety instruction document before using the product
and keep it available for future reference.
Introduction
TPS-TX87 and RX87 twisted pair HDBaseT TM extenders provide extension of
uncompressed 4K/UHD video with embedded audio for long distances over a single
CATx cable. The extender offers unidirectional RS-232 and IR pass- through on
the same Cat cable that carries the video signal. The TPS extenders support
full HDCP and EDID compliance and work on all standard AV resolutions and also
120 Hz 3D signals. PoE 48V remote powering is available through the single Cat
cable, but a local power supply can also be used.
Box Contents
Compatible Devices
TPS-87 extenders are compatible with all Light ware devices with TPS port
except the TPS-90 series.
Power Supply Options
TPS-87 extenders are compatible with IEEE 802.3af standard – Power over
Ethernet (PoE) – and can receive power over the TPS line.
The extenders are not compatible with TPS-95 extenders from remote power point
of view. TPS-95 extenders have a different remote power feature, which is not
Poe compatible. Please always check the devices before connecting them to each
other.
If the remote power feature is disabled on the TPS-95 extender, it can be
connected to a TPS-87 device.
The extenders can be powered:
- Locally with the supplied 12V DC adaptor or Light ware’s rack mountable PSU,
- Remotely by a PoE-compatible Power Sourcing Equipment (PSE) device, like Light ware’s power injector (TPS-PI-1P1) or a PoE-compatible matrix or matrix board.
If both supplying modes are available (local and remote), the remote power supply will be used.
Do not connect any device to the TPS connector unless you are sure they are compatible! Connecting incompatible devices with similar connectors may cause harm to the devices.
AWG 26 cables are not recommended with remote powering (reduce cable distances).
Connecting Steps
The layout below means the transmitter is powered locally by the power
injector and they are placed close to each other. The receiver is powered
remotely via the TPS cable (PoE).
CATx| Connect the TPS output port of the TX to the TPS port of the power
injector by a CATx cable.
---|---
CATx| Connect the TPS input port of the RX to the TPS+PoE port of the power
injector by a CATx cable.
DC-DC| Connect a DC-DC cable between the transmitter and the power injector.
HDMI| Connect a source to the HDMI (DVI-D) input port of the transmitter.
IR| Connect an IR emitter unit to the IR output port of the transmitter.
RS-232| Connect a controller device to the local RS-232 port of the
transmitter. Make sure the RS-232 switch is in Normal position.
HDMI| Connect a sink device to the HDMI (DVI-D) output port of the receiver.
RS-232| Connect a serial cable between the sink device and the RS-232 port of
the receiver.
IR| Connect an IR detector unit to the IR input port of the receiver.
Power| First, connect the power adaptor to the DC input of the power injector,
then secondly to the AC power socket.
Infrared emitter and detector units are optionally available accessories.
Locking DC Plug
The device has a locking DC connector to establish robust and safe power
connection when local PSU is used. Twist 90° clockwise to lock.
Mounting Options
Light ware offers three types of mounting accessories to fix the extenders:
Rack Shelf
1U high rack shelf provides mounting holes for the fastening of up to four
extenders.
Mounting Steps:
Always use the fixing screws that are supplied with the mounting accessory. If youinsert screws longer than 6 mm, the device can be damaged.
- Unplug all the cables connected to the device(s).
- Turn the device(s) upside down.
- Put the shelf upside down on the device(s). Position it to get the mounting holes aligned.
- Fasten the device on the shelf with the provided screws.
- Fix the shelf to the desired place (screws are not supplied).
Under Desk Mounting Kit (UD-kit)
The UD-kit makes it easy to mount one extender under any flat surface (e.g.
furniture).
UD Mounting Kit Double (UD-kit double)
The UD-kit double makes it easy to mount two extenders under any flat surface
(e.g. furniture).
Port Diagram
Installation of the Extender With a Matrix
- Power off all devices (installing with powered devices may harm them).
- Check the RS-232 switch(as) on the extender(s); they must be in Normal position for RS-232 pass-through function.
- The state of the TPS link mode switch makes no difference on the extender, because the connected board forces the extender to use the settings of the matrix.
- Check the PoE settings of the matrix or the matrix board (with the LDC software); each port can be set for remote powering separately.
- Pair the extender(s) and the matrix board(s) with CATx cable(s). The transmitters’ TPS OUT with the input boards’ TPS IN and the receivers’ TPS IN with the output boards’ TPS OUT.
- Connect the video source(s), sink(s) and the desired accessory device(s) to the matrix (MX-TPS boards don’t support the IR pass-through).
- Connect the video source(s), sink(s) and the desired accessory device(s) to the extenders.
- To supply the extender(s) with remote power supply, connect the necessary power adaptor to the given matrix board.
- To supply the extenders locally, connect the supplied adaptor (12V 2A DC).
- Connect the power cord of the matrix into the outlet and switch on the matrix.
- Supply the other connected units.
Bi-directional Pass-through Data Lines
The direction of the video extension is fixed from TX towards RX, but the
pass-through data lines are bi-directional*. It means the RS-232 mandir source
and sink devices can be connected either to the TX or to the RX, and the
signal is transmitted to the other extender.
- In fact IR transmission is unidirectional, but the extender has two IR channels with different directions.
RS-232
Third-party devices with standard RS-232 port are supported, as the extenders
work in „passthrough” mode.
TX and RX provide a 3-pole Phoenix connector.
The RS-232 options –the baud rate and the parity bits – are set on the third-
party devices and they can be anything. The extenders support any kind of
serial settings.
Please find the RS-232 device type in its user guide; the extenders work as
DCE devices.
RS-232 Switch Modes
Infrared (IR)
One emitter and one detector is enough for remote controlling one IR sink
device. If there is an IR sink device to be controlled next to the TX and the
other one is next to the RX, two emitter-detector pairs are needed. The IR
emitter and the detector have standard 3.5 mm TRS (jack) connectors. The
emitter’s plug has two poles (mono) and the detector’s plug has three poles
(stereo).
IR Output Mode Switch
The IR output signal modulation can be selected by the front panel switch as
follows:
|
---|---
1 Tip| Signal (active low)| 1 Tip| +5V
2 Ring| GND| 2 Ring| Signal (active low)
3 Sleeve| +5V| 3 Sleeve
- Emitter: the 38 kHz modulation is switched on. In this case, an IR emitter can be connected to the IR output port.
- Wired: the 38 kHz modulation is switched off. This option allows the connection of a cable between the IR output of the extender and the IR input port of the device desired to be remote controlled.
Standalone Application
Application Diagram
TPS Link Modes
The TPS working mode between the transmitter and the receiver parties is
determined by the mode set in them. Both parties influence on the setting that
determines the final TPS transmission mode. The following TPS modes are
defined:
- Long reach (LR) : Longer CATx cable length, less bandwidth (limited resolution). The LPPF mode is not available in LR TPS link mode.
- HDBaseT TM (HDBT): more bandwidth (higher resolutions), shorter CATx cable length. If no video is present, the units change to LPPF mode automatically.
- Low Power Partial Functionality (LPPF): Only RS-232 and IR are extended.
Toggling Between TPS Link Modes
The toggle switch on the extenders can be used to toggle between the LR and
Auto TPS modes. If both units have Auto state and there is valid video signal
on the transmitter, the common mode will be HDBT. If the video signal
disappears, devices go into LPPF mode.
| The negotiated TPS working mode | Selected mode (RX) |
|---|---|
| LR | Auto |
Selected
mode
(TX)| LR| LR| LR
Auto| LR| Auto
TPS mode between an extender and a port of a matrix board
If an extender and a TPS matrix board are paired, the board forces the
extender to use the settings of the matrix. The extender’s TPS mode switch has
no effect.
Always use the Auto mode with third-party devices!
Wiring Guide for RS-232 Data Transmission
TPS-87 extenders are built with a 3-pole Phoenix connector. See the examples
below of connecting to a DCE (Data Circuit-terminating Equipment) or a DTE
(Data Terminal Equipment) type device:
Light ware device and a DCE
D-SUB 9 – Phoenix| Light ware device and a DTE
D-SUB 9 – Phoenix
---|---
|
For more information about the cable wiring, see the user’s manual of the device or the Cable Wiring Guide on our website.
Maximum Extension Distances
Resolution| Pixel
clock rate| Cable lengths
(Auto I Long reach TPS mode)
---|---|---
CAT5e
AWG24| CAT7
AWG26 a| CAT7
AWG23
1024×768®60Hz| 65 MHz| 100 m 1130 m”| 90 m 1120 m| 120 m / 170 m”
1280x720p®60Hz| 73.8 MHz| 100 m / 130 m”| 90 m 1120 m| 120 m / 170 m”
1920x1080p®60Hz (24bpp)| 148.5 MHz| 100 m / 130 m”| 90 m 1120 ma| 120 m / 170
m”
1920×1200®60Hz| 152.9 MHz| 100 m / NA| 90 m I NA| 120 m / NA
1600×1200®60Hz| 162 MHz| 100 m / NA| 90 m I NA| 120 m / NA
1920×1080®60Hz (36bpp)| 223 MHz| 70 m / NA| 70 m I NA| 100 m / NA
3840×2160®30Hz UHD| 297 MHz| 70 m / NA| 70 m I NA| 100 m / NA
4096×2160®30Hz 4K| 297 MHz| 70 m / NA| 70 m I NA| 100 m / NA
- Long reach TPS mode supports pixel clock frequencies up to 148.5 MHz
** AWG 26 cables are not recommended with remote powering.
Above values are valid when the extender is powered by a local adaptor; distances may decrease depending on the powering mode (local or remote) and cable quality.
CAT7 SFTP AWG23 cable is always recommended.
Specification
General
Compliance ………………………………………………………………………………………………….CE
Electrical safety ………………………………………………………………… IEC/EN 62368-1:2014
EMC (emission) ………………………………………………………………….. IEC/EN 55032:2015
EMC (immunity) ………………………………………………………………….. IEC/EN 55035:2017
RoHS ………………………………………………………………………………………..EN 63000:2018
Warranty ………………………………………………………………………………………………. 3 years
Operating temperature ……………………………………………0° to +50°C (+32° to +122°F)
Operating humidity ………………………………………………… 10% to 90%, non-condensing
Cooling ………………………………………………………………………………………………….passive
Power
Power supply ………………………………………………………………………power adaptor / PoE
Power consumption (TX) ………………………………………………… 3.6W (typ) / 4.5W (max)
Heat dissipation (TX) …………………………………………. 13 BTU/h (typ) / 16 BTU/h (max)
Power consumption (RX) ……………………………………………….. 5.5W (typ) / 6.5W (max)
Heat dissipation (RX) …………………………………………. 19 BTU/h (typ) / 23 BTU/h (max)
Power over Ethernet (PoE) ………………………………………..via TPS port (IEEE 802.3af)
Power Adaptor
Supported power source …………………………………………………100-240 V AC; 50/60 Hz
Supplied power ……………………………………………………………………………..12V DC, 2.5A
AC power plug …………………………………….. Interchangeable (EU, UK, JP/US, AUS/NZ)
DC power plug ………………………………………… Locking DC connector (2.1/5.5 mm pin)
Enclosure
Enclosure material ……………………………………………………………………………. 1 mm steel
Dimensions in mm ………………………………………………………. 100.4 W x 100.4 D x 26 H
Dimensions in inch …………………………………………………………………. 4 W x 4 D x 1.1 H
Weight (TX) ………………………………………………………………………………………………285 g
Weight (RX) ……………………………………………………………………………………………..305 g
Video Input
Connector type (HDMI transmitters) ……………………..19-pole HDMI Type A receptacle
A/V standard ……………………………………………………………………….. DVI 1.0, HDMI 1.4a
HDCP compliance ………………………………………………………………………………HDCP 1.4
Color space …………………………………………………………………………………… RGB, YCbCr
Video delay ……………………………………………………………………………………………0 frame
Supported resolutions at 8 bits/color * …………………………………………………………………
………………………………. up to 4096×2048@30Hz (4:4:4) or 4096×2048@60Hz (4:2:0)
………………………………. up to 3840×2160@30Hz (4:4:4) or 3840×2160@60Hz (4:2:0)
………………………………………………………. 1920×1080@60Hz (4:4:4) up to 12 bits/color
Relocking ………………………………………………………………….Pixel Accurate Reclocking
3D support …………………………………………………………………………………………………. yes
Control over CEC ………………………………………………………………….. yes **, transparent
EDID support …………………………………………………………………………………. transparent
- All standard VESA, CEA and other custom resolutions up to 300MHz (HDMI1.4a)are supported.
Video Output
Connector type (HDMI receivers) ………………………….19-pole HDMI Type A receptacle
The specifications of the output port are the same as in the case of the input port.
Connectors
TPS port ………………………………………………………………………… RJ45 (PoE-compatible)
IR input, output …………………………. 3.5 mm (1.8”) jack connector, pass-through mode
Serial port ……………………………………… 3-pole Phoenix connector, pass-through mode
Further Information
The product brief and further information of this appliance is available at
www.lightware.com.
See the Downloads section on the website of the product.
Contact Us
sales@lightware.com
+36 1 255 3800
support@lightware.com
+36 1 255 3810
Light ware Visual Engineering LLC.
Petered 15, Budapest H-1071, Hungary
Doc. ver.: 1.1
19200204
Documents / Resources
|
LIGHTWARE HDMI-TPS-TX87 Twisted Pair HDBaseT
Extender
[pdf] User Guide
HDMI-TPS-TX87, HDMI-TPS-RX87, Twisted Pair HDBaseT Extender, HDMI-TPS-TX87
Twisted Pair HDBaseT Extender
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>