Imou IOT-ZP1-EU PIR Motion Sensor User Manual

Imou IOT-ZP1-EU PIR Motion Sensor

Product Information

• Product Description: PIR Motion Detector

• Status Indicator: Red and green LEDs

• Fresnel Lens: Included

• Network Setting: Wireless

• Installation Instructions: See below

• Technical Parameters:

  • Wireless Technology: Not specified

  • Working Voltage: Not specified

  • Transmission Frequency: Not specified

  • Working Temperature: Not specified

  • Under Voltage Alarm: Included

  • Detection Radius: Not specified

  • Detection Angle: Not specified

  • Installation Height: Recommended to be about 2.2m above the ground

  • Dimensions: Not specified

  • Toxic or Hazardous Substances or
    Elements:

  • Name:

  • Pb (Lead)

  • Hg (Mercury)

  • Cd (Cadmium)

  • Cr(VI) (Hexavalent Chromium)

  • PBBs (Polybrominated Biphenyls)

  • PBDEs (Polybrominated Diphenyl Ethers)

  • Components:

  • LED

  • PCB

  • Cover and other components

• Warranty Certificate:

  • Warranty Policy:
  • If the product has quality problems within 7 days of the payment date, you can apply for a refund based on the invoice price or to replace with the same model or have it repaired.
  • If the product has quality problems within 15 days of the payment date, you can apply to replace the product with the same model or have it repaired.
  • If the product has quality problems within 12 months of the payment date, you can apply to have it repaired.
  • What is not covered under this warranty:
  • The product owner has no warranty certificate or the warranty service has expired.
  • Damage caused by improper use, maintenance, or storage.
  • Damage caused by disassembly and repair without Tuya’s authorization.
  • Damage caused by force majeure.
  • Normal discoloration and depreciation after the product has been used.

Product Usage Instructions

1. Power on the product by removing the battery insulation film. The red LED will flash slowly for self-checking.
2. To set up the network, press the reset button for 5 seconds and release. The green LED will flash for network setting.
   • Distribution network hint: Press the reset button for 5s-10s, the red LED is on. Once the red LED turns off, release the reset button. The green LED flashes, which means ready for network setting. The green LED will be on for 5s then turn off to indicate network setting succeeds. If fails, the green LED is off.
3. Install the product where persons may be detected to cross, recommended to be about 2.2m above the ground.
   • Installation position: Install the product where persons may be detected to cross. It is recommended that the product be about 2.2m above the ground.
   • Product installation : Remove the protective film from the adhesive on the base and attach the base to the installation position. Correctly mount the product to the base.
   • Mount the product on the magnetic base.
   • Matters need attention:
   • Ensure that there are no obstacles in front of the product’s lens. Otherwise, the detection result may be inaccurate.
   • Wireless distance between detector and gateway will be shortened if there are obstacles such as walls.
   • Install the product away from objects that may cause temperature changes, such as the air conditioner, fan, refrigerator, and oven. Do not expose the product to the sun.

Product Description

Network Setting

1. Power on the product. Rotate the battery cover anticlockwise to open. Remove the battery insulation film to power on the product,  the red LED will flash slowly for self-checking.

2. Press the reset button for 5S and release, the green LED will flash for network setting.
   Distribetion network hint:

   • Press the reset button for 5s-10s, the red LED is on, once red LED turns off, release the reset button, the green LED  flashes, means ready for network setting.
   • The green LED will be on for 5s then turns off to indicate network setting succeeds. If fails, the green LED is off.

Installation Instructions

1. After powered on, the product will enter self-checking state and the red LED will flash for 60s.
2. After self-checking, the product enters test mode for 5 minutes. When it detects human motion, the red LED flash and sends an alarm signal.
3. During working status, press set button, the red LED flash once, then enter testing mode.
4. After testing mode, the detector enters working mode and no motion status. When human motion is detected, the red LED is on and sends an alarm signal. After alarm, if continuous motion is detected, it won’t send alarm signal. Until no motion is detected for 1 minute, it restores to no motion status and working mode.

Installation Instructions

1. Installation position: Install the product where persons may be detected to cross. It is recommended that the product be about 2.2m above the ground, as shown in the following figure.
2. Product installation: Remove the protective film from the adhesive on the base and attach the base to the installation position. Correctly mount the product to the base.
3. Matters need attention
4. Ensure that there are no obstacles in front of the product’s lens. Otherwise, the detection result may be inaccurate.
5. Wireless distance between detector and gateway will be shorten if there is obstacles such as walls.
6. Install the product away from objects that may cause temperature changes, such as the air conditioner, fan, refrigerator, and oven. Do not expose the product to the sun.

Technical Parameters

Toxic or Hazardous Substances or Elements of this Product

Warranty Certificate

Warranty policy:

1. If the product has quality problems within 7 days of the payment date, you can apply for a refund based on the invoice price or to replace with the same model or have it repaired..
2. If the product has quality problems within 15 days of the payment date, you can apply to replace the product with he same model or have it repaired.
3. If the product has quality problems within 12 months of the payment date, you can apply to have it repaired.

What is not covered under this warranty:

1. The product owner has no warranty certificate or the warranty service has expired.
2. Damage caused by improper use, maintenance, or storage
3. Damage caused by disassembly and repair without Tuya’s authorization
4. Damage caused by force majeure
5. Normal discoloration and depreciation after the product has been used

User Form

User information (Specify real information. Tuya promises to use the information only for after-sales services.)

Vendor Form

Jser information (Specify real information. Tuya promises to use the information only for after-sales services.)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>