INOR APAQ R130 RTD Programmable 2 Wire Transmitter Instruction Manual

INOR APAQ R130 RTD Programmable 2 Wire Transmitter

GENERAL INFORMATION

APAQ R130RTD is a low cost, non-isolated, easy-to-use 2-wire temperature transmitter for Pt100 and Pt1000 input, intended to be used in industrial environment.The transmitter is configured from a mobile device via NFC communication, by using the app INOR Connect. Inor Connect is available for free download on App Store, Google Play Store and Huawei AppGallery.

DATA (short form)

• Input 2-, 3-, 4-wire connection
• Pt100 (IEC 60751, α=0.00385) -200 to +850 °C / -328 to +1562 °F
• Pt1000 (IEC 60751, α=0.00385) -200 to +850 °C / -328 to +1562 °F
• Adjustments – ZeroAny value within range limits
• Adjustments – Minimum span 20 °C / 36 °F
• Output 4-20 mA, temperature linear
• Sensor failure indication Upscale (≥21.0 mA) or downscale (≤3.6 mA)
• NAMUR Compliance Current limitations and failure currents acc. to NAMUR NE 43
• Response time 0.4 to 26 s, adjustable filtering level

Ambient temperature

• Storage and operation -40 to +85 °C / -40 to +185 °F
• Galvanic isolation None
• Power supply 6 to 32 VDC
• Accuracy Max. of ±0,15 K or ±0,15 % of span
• Mounting Rail acc. to DIN EN50022, 35 mm
• Vibration IEC 60068-2-6, 5 g
• EMC EN 61326-1 and EN 61326-2-3
• Configuration App INOR Connect via NFC

Factory settings

• Input Pt100 3W, 0 to 100 °C
• Output 4 to 20 mA
• Sensor error indication Upscale

CONFIGURATION

Before making a configuration of APAQ R130RTD you need to do following:

1. Make sure that you have a mobile device with NFCcommunication activated
2. Download the app INOR Connect to your mobile device

Required versions:

iOS
iOS 13 or later and Iphone 7 or later for NFC

Android
Android 4.4 or later

Configuration procedure

1. Launch the app by clicking on the Appicon or holding your mobile device against the transmitter on the part of the device where NFC is located(only possible with Android).
2. Click on “Read Configuration” and hold your mobile device against the transmitter as explained in the first section.
3. In the app you can edit the following:
4. Sensor type and number of wires
5. Measuring range
6. Upscale or downscaleSensor error indication
7. Filter level
8. TAG-number
9. Password
10. Once you have set the desired values in theapp, you transfer it to the transmitter byclicking the transfer button and holding themobile device against the transmitteruntil a green check box appears confirmingthat the transfer has been completed.

INSTALLATION

APAQ R130RTD is designed to be mounted on a 35 mm DIN Rail accordingto EN 60715 / DIN 50022. Connect in put, output and power supply acc. to “CONNECTIONS”. The cable is connected using spring-cage connection. In order to minimize measuring errors ensure that the cable is securely fastened.

1. Insert a screwdriver into the opening above the connection terminal block.
2. Insert the wire into the corresponing connection terminal block

MOUNTING

Mounting and removal of the transmitter

1. Fix the upper part of the transmitter onto the rail.
2. Press the lower part of the transmitter against the rail.
3. To remove the transmitter, use a screwdriver and bend the locking under the transmitter downwards.

CONNECTIONS

ORDERING INFORMATION
The transmitters are delivered with either a default factory setting or configured according to customer’s specification

LIMITED WARRANTY

INOR Process AB, or any other affiliated company within the Inor Group (hereinafter jointly referred to as ”Inor”), hereby warrants that the Product will be free from defects in materials or workmanship for a period of five (5) years from the date of delivery (”Limited Warranty”). This Limited Warranty is limited to repair or replacement at Inor’s option and is effective only for the first end-user of the Product. Upon receipt of a warranty claim, Inor shall respond within a reasonable time period as to its decision concerning:

1. Whether Inor acknowledges its responsibility for any asserted defect in materials or workmanship; and, if so,
2. the appropriate cause of action to be taken (i.e. whether a defective product should be replaced or repaired by Inor).

This Limited Warranty applies only if the Product:

1. is installed according to the instructions furnished by Inor;
2. is connected to a proper power supply;
3. is not misused or abused; and
4. there is no evidence of tampering, mishandling, neglect, accidental damage, modification or repair without the approval of Inor or damage done to the Product by anyone other than Inor.

This Limited Warranty is provided by Inor and contains the only express warranty provided. INOR SPECIFICALLY DISCLAIMS ANY EXPRESS WARRANTY NOT PROVIDED HEREIN AND ANY IMPLIED WARRANTY, GUARANTEE OR REPRESENTATION AS TO SUITABILITY FOR ANY PARTICULAR PURPOSE, PERFORMANCE, QUALITY AND ABSENCE OF ANY HIDDEN DEFECTS, AND ANY REMEDY FOR BREACH OF CONTRACT, WHICH BUT FOR THIS PROVISION, MIGHT ARISE BY IMPLICATION, OPERATION OF LAW, CUSTOM OF TRADE OR COURSE OF DEALING, INCLUDING IMPLIED WARRANTIES OF MER-CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. EXCEPT AS PROVIDED HEREIN, INOR FURTHER DISCLAIMS ANY RESPONSIBILITY FOR LOSSES, EXPENSES, INCONVENIENCES, SPECIAL, DIRECT, SECONDARY OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THE PRODUCT. Products that are covered by the Limited Warranty will either be repaired or replaced at the option of Inor. Customer pays freight to Inor, and Inor will pay the return freight by post or other “normal” way of transport. If any other type of return freight is requested, customer pays the whole return cost.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>