tp-link T100 Smart Motion Sensor User Guide
- October 30, 2023
- tp-link
Table of Contents
tp-link T100 Smart Motion Sensor
Before You Start
A Tapo Hub is required. Make sure your Tapo Hub is successfully added via the Tapo app.
Power Up Your Sensor
Remove the battery insulation tab to power up your sensor. The LED should
blink.
Note : If the LED is not blinking, refer to the reverse side for reset
instructions.
Set Up Your Sensor
Open the Tapo app and tap the button.
Select Sensors and then your model.
Follow the app instructions to complete setup.
Test Your Sensor
Take your sensor to the preferred location and wave your hand in front of the
sensor to test it. The Tapo app should show if the sensor is triggered.
Place Your Sensor
Option 1:
Magnetically attach to metallic objects
Option 2:
Stick to a clean wall with included adhesive
Option 3:
Place it on a shelf or table
Detection Area
The sensor should be aligned with the detection area and placed as close as
possible to the edge of a table or cabinet. The installation height should not
be higher than 2 meters.
Meet Your Motion Sensor
The Motion Sensor detects movement in a certain area and triggers different
actions in response. This makes your home safer and smarter.
How to Replace The Battery
-
Option 1: With a Shim
-
Option 2: By Hand
How To Reset Your Sensor
Use a pin to press and hold the Reset button for 5 seconds until the front LED starts blinking.
Need some help?
Visit www.tapo.com/support/ for technical
support, user guides, FAQs, warranty & more
Safety Information
Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper use
of the device. Please use this product with care and operate at your own risk.
Do not ingest battery, Chemical Burn Hazard
This product contains a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and
keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
CAUTION!
Avoid replacement of a battery with an incorrect type that can defeat a
safeguard.
Avoid disposal of a battery into fire or a hot oven, or mechanically crushing
or cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable liquid
or gas; Do not leave a battery subjected to extremely low air pressure that
may result in an explosion or the leakage of flammable liquid or gas.
For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be found at
https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment Regulations
2017.
The original UK declaration of conformity may be found at
https://www.tapo.com/support/ukca/
Setup Video
Scan QR code or visit https://www.tp-link.com/support/ setup-video/#smart-
sensors
References
- Support | Tapo
- Regulatory Compliance | Tapo
- UKCA | Tapo
- TP-Link Product Support - Wireless Networking Equipment Support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>