Cesicia Vintage Chandelier Instruction Manual

Cesicia Vintage Chandelier

Product Information

The MODEL 900015 is a circular fixture that includes 4 arms and a light cluster with wires. The package comes with a chain and loops, a canopy, mounting bracket with nipple, and 8 candle sleeves. The fixture has a required supply circuit of 120V, 60Hz and can handle a maximum of 8E1240W wattage. The compatible bulb type is 9W LED Candelabra bulb which is not included in the package.

Product Usage Instructions

1. Open the package carefully and take out all the components, parts bag, and manual from the box.
2. Verify that all the components are present by checking them against the parts list. If any part is missing or damaged, contact the manufacturer at support@micsiu.com for a replacement.
3. Follow the assembly steps as illustrated below:
4. Straighten the 8 folded sockets(T) on the fixture frame(W). Assemble the 4 arms(P) to the circular frame(W) and fix them with 8 cylinder nuts(S). Pull the wires gently through the arms for later wiring with the fixture wires(K) inside the cup(O).
5. Release the hex nuts(U) and washers(V) from the arms(P). Also, release the cap(N) from the cup(O) and fixture wires(K). Slide the cup(O) onto the arms(P), then fasten it with hex nuts(U) and washers(V) by Allen wrench(X).
6. Use wire nuts(C) to connect the wires black with black, white with white, or according to the wiring diagram. Then slide the cap(N) onto the top of cup(O) through the short nipple and wires(K), fix it with the ring(M) and loop(L). Fixture wires(K) go through these parts at this step.
7. Adjust the length of the chain to your desired hanging height. Thread to open the chain lockers(I) on the ends of the chain(J). Connect one end with loop(L) and fixture, connect the other end with canopy(F). Wires(K) go through the hanging loop(G), collar(H), and canopy(F) for later wiring.
8. Install the mounting bracket with nipple(D) to the junction box(A) by the mounting screws(E).
9. Connect wires according to the wiring diagram on the right.
10. Thread the hanging loop(G) onto the nipple of mounting bracket(D) to hang the fixture. Thread the collar(H) to fix the canopy(F) onto the junction box(A).
11. Slide the candle sleeves(R) onto the sockets(T). Screw on the light bulbs(Q) onto the sockets(T).

Note: The shape and style of fixture / glass / shade / diffuser may vary even though this is a generic instruction sheet used for various fixtures.

Assembly & Installation Instructions

MODEL: 900015

IMPORTANT SAFETY INSTRUCTIONS:

• • Warning: If any special control devices are used with this fixture, follow the instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, please contact a qualified electric contractor.
  • Warning: This product can expose you to chemicals including lead, which is known to the State of California, to cause cancer or birth defects or other reproductive harm. For more information,please go to
  www.P65Warnings.ca.gov
  • Caution: Electrician installation is highly recommended. All glass is fragile, use care when handling glass component(s) and or lamp(s). Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.

Important Notice:

This is a generic instruction sheet used for various fixtures. The shape and style of fixture / glass / shade / diffuser may vary.

(Required Supply Circuit: 120V, 60Hz. Watt: 8E1240W Max)

Compatible Bulb Type (NOT Included)

The mostly suggested bulb type is 9W LED Candelabra bulb

COMPONENTS INCLUDED IN THE PACKAGE
Circular fixture frame, 4 Arms, Light cluster with wires, Chain and loops, Canopy, Mounting bracket with nipple, 8 Candle sleeves

Parts included in parts bag

ASSEMBLY & INSTALLATION STEPS:

1. Open the box from top, take out all the components, parts bag and manual from the box carefully.
2. Check all the components against the parts list. Make sure you have got each parts on list. If any parts missing or glass damage, please contact manufacturer at: support@micsiu.com to get a replacement.
   Parts are NOT included for which is shown as 0 under QTY.

PARTS  LIST

Part Name| QTY| Code|  | Part Name| QTY| Code
Junction Box| 0| A| Ring| 1| M
Leading Wires| 0| B| Cap| 1| N
Wire Nut| 5| C| Cup| 1| O
Mounting Bracket with Nipple| 1| D| Arm| 4| P
Mounting Screw| 3| E| Light Bulb| 0| Q
Canopy| 1| F| Candle Sleeve| 8| R
Hanging Loop| 1| G| Cylinder Nut| 8| S
Collar| 1| H| Folded Socket| 8| T
Chain Locker| 2| I| Hex Nut| 4| U
Chain| 1| J| Washer| 4| V
Fixture Wire| 2| K| Circular Fixture Frame| 1| W
Loop| 1| L| Allen Wrench| 1| X
3. Refer to the illustration while doing assembly and follow the steps as below:

1. Straighten 8 folded sockets(T) on the fixture frame(W). Assemble 4 arms(P) to the circular frame(W) and fix with 8 cylinder nuts(S). Pull the wires gently through the arms for later wiring with the fixture wires(K) inside the cup(O).

2. Release the hex nuts(U) and washers(V) from the arms(P). Also release the cap(N) from the cup(O) and fixture wires(K). Slide the cup(O) onto the arms(P), then fasten with hex nuts(U) and washers(V) by Allen wrench(X).

3. Use wire nuts(C) to connect the wires black with black, white with white, or according to the wiring diagram.
   Then slide the cap(N) onto the top of cup(O) through the short nipple and wires(K), fix with the ring(M) and loop(L). Fixture wires(K) go through these parts at this step.

4. Adjust the length of the chain to your desired hanging height. Thread to open the chain lockers(I) on the ends of the chain(J). Connect one end with loop(L) and fixture, connect the other end with canopy(F). Wires(K) go through the hanging loop(G), collar(H) and canopy(F) for later wiring.

5.  Install the mounting bracket with nipple(D) to the junction box(A) by the mounting screws(E).

6. Connect wires according to the wiring diagram on the right.

7. Thread the hanging loop(G) onto the nipple of mounting bracket(D) to hang the fixture. Thread the collar(H) to fix the canopy(F) onto the junction box(A).

8.  Slide the candle sleeves(R) onto the sockets(T). Screw on the light bulbs(Q) onto the sockets(T).

Illustration of assembly and wiring:

• I. P, S → W
• II. U, V, O → P
• III. L, M, N → O
• IV. F, G, H, I, J → L
• V. D, E A VI. B, K → C
• VII. H, G, F → D
• VIII. R, Q → T

References

• P65Warnings.ca.gov
• p65warnings.ca.gov/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>