Cesicia 900017 Modern Crystal Design 3-Light Oil Rubbed Bronze Circle Chandelier Instruction Manual
- October 30, 2023
- Cesicia
Table of Contents
Cesicia 900017 Modern Crystal Design 3-Light Oil Rubbed Bronze Circle
Chandelier
IMPORTANT SAFETY INSTRUCTIONS:
- Warning: If any special control devices are used with this fixture, follow the instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, please contact a qualified electric contractor.
- Warning: This product can expose you to chemicals including lead, which is known to the State of California, to cause cancer or birth defects or other reproductive harm. For more information, please go to www.P65Warnings.ca.gov
- Caution: Electrician installation is highly recommended. All glass is fragile, use care when handling glass component(s) and or lamp(s). Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.
Important Notice:
This is a generic instruction sheet used for various fixtures.
The shape and style of fixture / glass / shade / diffuser may vary.
(Required Supply Circuit: 120V, 60Hz. Watt: 3E2660W Max)
Compatible Bulb Type (NOT Included)
The mostly suggested bulb type is 11W LED A19 bulb
COMPONENTS INCLUDED IN THE PACKAGE
Arm / Ring / Light Cluster / Crystal / Chain & Loops / Cup / Canopy / Bracket
with Nipple
Parts included in parts bag
ASSEMBLY & INSTALLATION STEPS:
- Open the box from top, take out all the components, parts bag and manual from the box carefully.
- Check all the components against the parts list. Make sure get each parts on list. If any parts missing or glass damage, please contact manufacturer at: support@micsiu.com to get a replacement.
Parts are NOT included for which is shown as 0 under QTY.
PARTS LIST
Part Name| QTY| Code| | Part Name| QTY| Code
Junction Box| 0| A| Cap| 1| N
Leading Wires| 0| B| Hex Nut| 1| O
Wire Nut| 3| C| Ribbed Nut| 6| P
Mounting Bracket with Nipple| 1| D| Plastic Washer| 6| Q
Mounting Screw| 3| E| Screw| 6| R
Canopy| 1| F| Central Rod| 1| S
Hanging Loop| 1| G| Arm| 3| T
Collar| 1| H| Light Bulb| 0| U
Chain Locker| 2| I| Light Cluster with Socket| 1| V
Chain| 1| J| Cup| 1| W
Fixture Wire| 2| K| Large Ring| 1| X
Loop| 1| L| Crystal Clip| 56| Y
Small Ring| 1| M| Crystal| 56| Z
Refer to the illustration while doing assembly and follow the steps as below:
- Assemble 3 arms(T) which ends with a tab onto the large ring(X) using screws(R) and plastic washers(Q) from the inside and fix with ribbed nuts(P) from the outside. Make sure the holes to hang the crystals are facing down.
- Assemble the top ends of 3 arms(T) onto the cup(W) using screws(R) from the inside, fix with plastic washers (Q) and ribbed nuts(P). The washers(Q) are used between the arm tops and cup to prevent scratches during assembly.
- Thread the bottom of central rod(S) onto the light cluster(V), the top of rod(S) goes through the central hole of cup(W), fix the rod with the hex nut(O). Slide on the cap(N), small ring(M), and fasten with the loop(L). Fixture wires(K) go through these parts at this step.
- Adjust the length of the chain to your desired hanging height. Thread to open the chain lockers (I) on the ends of the chain (J). Connect one end with loop (L) and fixture, connect the other end with canopy (F), then close the chain lockers. Wires (K) go through the hanging loop (G), collar (H) and canopy (F) for later wiring.
- Install the mounting bracket with nipple (D) to the junction box (A) by the mounting screws (E).
- Connect wires according to the wiring diagram on the right.
- Thread the hanging loop (G) onto the nipple of mounting bracket (D) to hang the fixture. Thread the collar (H) to fix the canopy (F) onto the junction box.
- Insert the crystal clips(Y) into the holes on the crystals(Z), and clip them to hold the crystals onto the large ring(X) tightly. Screw on the bulbs(U) to the socket(V).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>