tp-link LS1005G, LS1008G Gigabit Desktop Switch Installation Guide
- October 30, 2023
- tp-link
Table of Contents
tp-link LS1005G, LS1008G Gigabit Desktop Switch Installation Guide
LED Explanation
Power
On: Power on
Power Off: Power off
Link/Act
Link/Act (Green)
On: Running at 10/100/1000Mbps
Flashing: Transmitting/receiving data
Off: No device is linked to the
corresponding port
Note: For simplicity, we will take LS1008G for example throughout this Guide.
Connection
Frequently Asked Questions (FAQ)
Q1. The Power LED is not lit.
The Power LED should be lit when the power system is working normally. If the
Power LED is not lit, check as follows:
A1:Make sure the power adapter is connected to the switch with power source
properly.
A2:Make sure the voltage of the power supply meets the requirements of the
input voltage of the switch.
A3: Make sure the power source is ON.
Q2. The Link/Act LED is not lit when a device
is connected to the corresponding port.
It is recommended that you check the following items:
A1:Make sure that the cable connectors are firmly plugged into the switch and
the device.
A2:Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet).
Specifications
General Specifications
| Standard | EEE802.3, IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x |
|---|---|
| Protocol | CSMA/CD |
| Data Transfer Rate | Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex) Fast |
Ethernet: 100Mbps (Half Duplex), 200Mbps (Full Duplex) Gigabit Ethernet:
2000Mbps (Full Duplex)
Network Media (Cable)| 10Base-T: UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m) 100Base-TX: UTP category 5, 5e cable
(maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) 1000Base-T: UTP category 5e
cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m)
Interface| 5/8 10/100/1000Mbps Auto-Negotiation RJ45 Ports
LED Indicators| Power, Link/Act LED
Transfer Method| Store-and-Forward
MAC Address Learning| Automatically learning, automatically aging
Frame Forward Rate| 10Base-T: 14881pps/Port 100Base-TX: 148810pps/Port
1000Base-T: 1488095pps/Port
Wall Mountable| Yes
Distance Between
Mounting Holes| LS1005G: 38mm
LS1008G: 48mm
Environmental and Physical Specifications
| Operating Temperature | 0˚C to 40˚C (32˚F to 104˚F) |
|---|---|
| Operating Humidity | 10% to 90%RH non-condensing |
| Storage Humidity | 5% to 90%RH non-condensing |
TP-Link hereby declares that the device is in compliance with the essential
requirements and other
relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC,
2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-
link.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other
relevant provisions of the Electromagnetic Compatibility Regulations 2016 and
Electrical Equipment
(Safety) Regulations 2016.
The original UK declaration of conformity may be found at https://www.tp-
link.com/support/ukca/
Safety Information
-
Keep the device away from water, fire, humidity or hot environments.
-
Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us -
Do not use damaged charger or USB cable to charge the device
-
Do not use any other chargers than those recommended.
-
Adapter shall be installed near the equipment and shall be easily accessible.
To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community.
For technical support and other information, please visit https://www.tp-
link.com/support, or simply scan the QR code.
References
- TP-Link Community
- CE Regulatory Compliance | TP-Link
- TP-Link Product Support - Wireless Networking Equipment Support
- Regulatory Compliance | TP-Link
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>