SparkLAN WPEQ-276AX Wireless Embedded WiFi Module Instruction Manual
- October 30, 2023
- SparkLAN
Table of Contents
SparkLAN WPEQ-276AX Wireless Embedded WiFi Module
Specification
| Standards | IEEE 802.11ax 2T2R 6G |
|---|---|
| Chipset | Qualcomm Atheros QCN9072 |
| Data Rate | 802.11ax: HE0~11 |
| Operating Frequency | IEEE 802.11ax 5.925~7.125GHz *Subject to local |
regulations
Interface| WLAN: PCIe
Form Factor| Mini PCIe
Antenna| 2 x IPEX MHF1 connectors
Modulation| Wi-Fi : 802.11ax: OFDMA (BPSK, QPSK, DBPSK, DQPSK, 16-QAM,
64-QAM, 256-QAM, 1024-QAM, 4096-QAM )
**Power Consumption| TX mode: 1288mA(Max.)
RX mode: 965mA(Max.)
Operating Voltage| DC 3.3V
Operating Temperature Range| -20°C ~ +70°C
Storage Temperature Range| -20°C ~ +90°C
Humidity (Non-Condensing)| 5%~90% (Operating)
5%~90% (Storing)
Dimension L x W x H (in mm)| 50.80mm(±0.15mm) x 29.85mm(±0.15mm) x
9.30mm(±0.3mm)
Weight (g)| 14.82g
Driver Support| Linux
Security**| 64/128-bits WEP, WPA, WPA2,WPA3,802.1x
Block diagram:
Installation
- Connect the Module to the PCIe slot of the computer.
- Install Wi-Fi driver driver.
- After the Wi-Fi Driver is installed , click the Network icon on the Windows, then search the network and connect the Wireless Network you want.
Federal Communication Commission Interference Statement:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected. Consult the dealer or an experienced radio/TV
technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
RF exposure statements
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons.
CFR 47 SUBPART E (15.407) has been investigated. It is applicable to the modular transmitter.
The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product.
This radio transmitterRYK-WPEQ276AX has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Unique antenna connector must be used on the Part 15 authorized transmitters used in the host product.
Antenna Type| Brand| Antenna Model|
Maximum Gain (dBi)
|
Remark
---|---|---|---|---
6 GHz
Dipole| SparkLAN| AD-506AX|
4.98 dBi
|
Dipole| SparkLAN| AD-501AX|
5 dBi
|
Length of Antenna cable:150mmConnector
type of Antenna cable: I-PEX/MHF4 to RP- SMA(F)
Dipole| SparkLAN| AD-509AX|
5 dBi
|
Dipole| SparkLAN| AD-507AX|
4.94 dBi
|
Dipole| SparkLAN| AD-508AX|
4.94 dBi
|
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID:RYK-WPEQ276AX” Or “Contains FCC ID:RYK-WPEQ276AX”
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
Manufacturers of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the users manual.
The module is for indoor applications only.
The module may not be used for the purposes of remote control of drones
The antenna must be installed into the host device so that the end user does not have access to the antenna or its connector.
Minimum antenna gain, including any cable losses, for the 6GHz bands must exceed 0dBi.
Label Indoor Only Info & restrictions.
FCC regulations restrict the operation of this device to indoor use only.
Operation prohibited on oil platforms, cars, trains, boats, and aircraft,
except that operation of this device is permitted in large aircraft while
flying above 10,000 feet.
OEM Integrator must refer to FCC KDB “996369 D04 Module Integration Guide v02” for modular transmitter integration guidance.
Industry Canada statement:
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This radio transmitter (IC: 6158A-WPEQ276AX has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Antenna Type| Brand| Antenna Model|
Maximum Gain (dBi)
| Remark
---|---|---|---|---
6 GHz
Dipole| SparkLAN| AD-506AX|
4.98 dBi
|
Dipole| SparkLAN| AD-501AX| 5 dBi| Length of Antenna cable:150mmConnector
type of Antenna cable: I-PEX/MHF4 to RP- SMA(F)
Dipole| SparkLAN| AD-509AX| 5 dBi|
Dipole| SparkLAN| AD-507AX| 4.94 dBi|
Dipole| SparkLAN| AD-508AX| 4.94 dBi|
If the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 6158A- WPEQ276AX”.
Manual Information To the End User:
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
Must use the device only in host devices that meet the FCC/ISED RF exposure
category of mobile, which means the device is installed and used at distances
of at least 20cm from persons.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance
statements related to the transmitter as show in this manual.
Host manufacturer is responsible for compliance of the host system with module
installed with all other applicable requirements for the system such as Part
15 B, ICES 003.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED
requirements for the transmitter when the module is installed in the host.
Must have on the host device a label showing Contains FCC ID: RYK-WPEQ276AX,
Contains IC:6158A- WPEQ276AX
The use condition limitations extend to professional users, then instructions
must state that this information also extends to the host manufacturer’s
instruction manual.
If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
Operation shall be limited to indoor use only.
Operation on oil platforms, cars, trains, boats and aircraft shall be
prohibited except for on large aircraft flying above 10,000 ft.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>