SparkLAN WPEQ-268AXI Wireless Module User Manual
- June 9, 2024
- SparkLAN
Table of Contents
SparkLAN WPEQ-268AXI Wireless Module
SPECIFICATION
- Standards
- IEEE 802.11ax/ac/a/b/g/n (2T2R)
- Bluetooth V5.2, V5.1, V5.0, V4.2, V4.1, V4.0LE, V3.0, V2.1+EDR
- Chipset
- Qualcomm Atheros WCN6856
- Data Rate
- 802.11b: 11Mbps
- 802.11a/g: 54Mbps
- 802.11n: MCS0~15
- 802.11ac: MCS0~9
- 802.11ax: HE0~11
- Bluetooth: 1 Mbps, 2Mbps and Up to 3Mbps
- Operating Frequency
- IEEE 802.11ax/ac/a/b/g/n
- ISM Band, 2.412GHz~2.484GHz, 5.150GHz~5.850GHz ,5.925~7.125GHz
- Subject to local regulations
- Interface
- WLAN: PCIe
- Bluetooth: USB
- Form Factor
- Half Mini PCI-e
- Antenna
- 2 x IPEX MHF1 connectors
- (Ant 1 for WLAN/BT, Ant 2 for WLAN)
- Modulation
- Wi-Fi:
- 802.11b: DSSS (DBPSK, DQPSK, CCK)
- 802.11g: OFDM (BPSK, QPSK, 16-QAM, 64-QAM)
- 802.11n: OFDM (BPSK, QPSK, 16-QAM, 64-QAM)
- 802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM)
- 802.11ac: OFDM (BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM)
- 802.11ax: OFDMA (BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM) BT:
- Header: GFSK
- Payload 2M: π/4-DQPSK
- Payload 3M: 8-DPSK
- Operating Voltage
- DC 3.3V
- Operating Temperature Range
- WPEQ-268AXI(BT) :-40°~+75°C (Operating)
- WPEQ-268AX(BT) :-10°~+65°C (Operating)
- Storage Temperature Range
- -45°C~90°C
- Humidity
- 5%~90% (Operating)
- (Non-Condensing)
- 5%~90% (Storing)
- Dimension L x W x H (in mm)
- 29.85mmx 26.65mmx 2.5mm
- Weight (g)
- 3.2g
- Security
- 64/128-bits WEP, WPA, WPA2, WPA3, 802.1x
Block Diagram
Installation
- Connect the Module to the PCIe slot of the computer.
- Install Wi-Fi driver driver.
- After the Wi-Fi Driver is installed , click the Network icon on the Windows, then search the network , and connect the Wireless Network you want.
Federal Communication Commission Interference Statement:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
RF exposure statements
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons. CFR 47 FCC PART 15 SUBPART C (15.247) and SUBPART E (15.407) has been investigated. It is applicable to the modular transmitter. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This radio transmitter RYK- WPEQ268AXBT has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
A unique antenna connector must be used on Part 15 authorized transmitters
used in the host product.
If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.
This exterior label can use wording such as the following:
“Contains Transmitter Module FCC ID: RYK-WPEQ268AXBT” Or “ Contains FCC
ID: RYK-WPEQ268AXBT” The modular transmitter is only FCC-authorized for the
specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the
host product manufacturer is responsible for compliance to any other FCC rules
that apply to the host not covered by the modular transmitter grant of
certification. The final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed. Manufacturers of
U-NII devices are responsible for ensuring frequency stability such that an
emission is maintained within the band of operation under all conditions of
normal operation as specified in the users manual.The module is for indoor
applications only.The module may not be used for the purposes of remote
control of dronesThe antenna must be installed into the host device so that
the end user does not have access to the antenna or its connector.Minimum
antenna gain, including any cable losses, for the 6GHz bands must exceed
0dBi.When installed in the host there cannot be a direct connection to the
internet
Industry Canada statement:
This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Caution:
- The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
- For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
- For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This radio transmitter (IC :6158A-WPEQ268AXBT has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
If the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 6158A- WPEQ268AXBT”.
Manual Information To the End User:
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual. Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID:RYK-WPEQ268AXBT, Contains IC:6158A-WPEQ268AXBT The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer’s instruction manual. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
Operation shall be limited to indoor use only.
Operation on oil platforms, cars, trains, boats and aircraft shall be
prohibited except for on large aircraft flying above 10,000 ft.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>