DIMENSION TECHNOLOGY EasyGet WiFi Wireless Fiber Endface Inspection Kit User Manual
- October 30, 2023
- DIMENSION TECHNOLOGY
Table of Contents
DIMENSION TECHNOLOGY EasyGet WiFi Wireless Fiber Endface Inspection Kit
Please read this manual before use. After reading this manual, please properly keep this manual, for future reference.
INTRODUCTION
Dear customer
Thank you for choosing EASYGETWIFI product. This product has high quality and
excellent performance. To make full use of this product, please read this
manual carefully before using. Whenever you have any questions, please contact
us and we are happy to support.
Symbols
The following symbols are used for the important information in this
manual.
- prompt The notice and restrictions in the process.
Attention
- Any change of this manual will not do any notice. Please kindly understand.
- As far as possible, the content of this manual is to maintain accurate. However , If it is found that there is no clear, erroneous or ambiguous content, please contact us.
Considerations about the product
- Keep the face clean video microscope, no fat, no pollution.
- Keep the handheld display clean, prevent TFT LCD screen by the sharp cut, or crushed by the weight.
- Put it in suit box if longtime no use.
- Please check the device before use, if you only have a lamp flashing that lights please charge before use.
PRODUCT Warranty
Warranty Term
We warrants that for a period of one (1) year from the Shipping Date, the
product purchased by customer shall be free of defects in material and
workmanship under normal authorized use consistent with the product
instructions.
Warranty Content
In the event that we receives notice during the warranty period that any
part does not conform to its warranty, our sole and exclusive liability shall
be, at its sole option, to either repair or replace the non-conforming part in
accordance with this limited warranty.
Warranty Exception
No warranty will apply if
- Device damage caused by wrong operation;
- Unconventional repair or modification;
- The causes of failure outside of the instrument;
- Used in high temperature and humidity, corrosive gas, harsh conditions such as vibration;
- Fires, earthquakes and other natural disasters as well as the pollution caused by radioactive substances and harmful substances, and when the other force majeure such as war, riot, crime.
- Consumables and consumable parts.
Structure Of This Manual
- Profile This chapter describes the name and function of each part.
- Hardware basic operation This chapter describes performance characteristics and the basic operation of the equipment.
- Software basic operation This chapter introduces software installation, features, interface and basic operation instructions.
- Contact us This chapter mainly list the contact information.
Profile
Check the packaging
Check whether include the following parts. We very carefully delivered of
each package, such as found missing, Please contact our after-sales staff.
According to the packing list of the products, please check whether all items
contained, if there are any missing items, please according to provide the way
to contact us.
Product description
- Adapter interface: connect different connector.
- Focus Ring: Regulating equipment focus clarity.
- Floodlight LED: Conducive to the operation of various environments.
- QR code: Scan get app.
- Label: Indicates important information about the product.
- Screenshot button: Trigger camera function in WIFI mode.
- Battery cover: Used to replace the battery.
- S/N: The number corresponds to the device.
- Light switch: Used for control lighting.
- WiFi LED light: Displays the WiFi state.
- Battery LED light: Displays the battery power and the storage status during the charging process.
- Power: Control device power switch.
- Power LED light: Displays the electrical state of the device.
- USB interface; The battery can be charged using the supplied USB cable and the adapter. WIFI switch?Enable or close the WIFI module.
Label
Hardware basic operation
Features
- Varies of adapters meet different requirements on inspect male fiber connector female fiber connector, such as FC SC ST E2000 LCMU and TOSA ROSA fiber end-face.
- EasyGetWiFi has high quality optical component and high resolution CCD sensor.
- Support wireless WiFi and USB two connections.
- Equipped with a dedicated rechargeable battery, a charge can work continuously for 5 hours.
- User-friendly design, the use of lighting in the dark when the use of more convenient light; the use of protective cover in the use of transport process, the equipment interface to protect and prevent dust fall.
- The fuselage is equipped with a quick screenshot button function, you can always record the situation of the fiber end-face by the image and stored in your smart device.
Performance
Hardware operation
LED light
Focusing method
As shown in the direction of the EasyGetWiFi device, rotate the focus ring
clockwise and the connector is away from the fuselage direction; Turn the
focal ring counterclockwise and the connector moves in the direction of the
fuselage.
WIFI use method
As shown in figure, the WiFi switch is moved to the device WiFi icon
indicating direction and the WiFi module is opened. When the WiFi indicates
that the green light is always on, the WiFi name of the device can be
connected with the mobile terminal device, which shows that the connection is
successful and the software can be used normally.
Note: WiFi name is 12345678.
Measure
The device measuring button will only be used when the device is enabled for
WiFi and connected to the mobile device. In USB transmission mode, the
measuring button is invalid. When the WiFi module is enabled, the mobile
terminal device connects to the WiFi name of the device, enters the software,
and press the device measuring button, The software will measure and analyze
the current end face. This feature is consistent with the mobile terminal
software interface measuring button.
Floodlight
Turn on the light switch as shown in the picture, for lighting when the light is dark.
Battery install
Installation method:
- On the battery cover, use a special screwdriver to loosen the screw to remove the battery cover.
- In the direction of the figure 2-6 shown, insert the battery connector into the internal connector.
- The battery tilted a certain angle into the battery slot, not directly into the horizontal level.
- As figure 2-7, install the battery cover, lock the screws.
Install complete:
NOTE:
- After removing the battery for the first time, please activate the device.
- Use a power supply to charge during the shutdown state of the device, and it will take about 2.5 hours to charge.
- When the low light of the power indicator is flashing, the equipment needs to be charged, otherwise, the equipment will be automatically cut off after a certain time. In order not to affect the performance of the equipment and normal use, please charge in time.
- In the charging process, the power indicator will be in sequence: the three indicators will blink in sequence. The low post is bright, the middle and the high are flashing. The low and middle post is bright, the high are flashing. The three lights are always bright and the battery is full.
Replace the adapter
Replace the adapter:
- Loosen the lock nut of the adapter.
- Remove the adapter.
- Insert a new adapter.
- Groove alignment.
- Re-tighten the lock nut
Software basic functions
Software installation and update
Mobile device software installation, by scanning the QR code, directly in the
application platform to download and follow the prompts to install.
Software features
- Software supports Windows, android, IOS
- The software supports transmitting the video image from the WiFi wireless connection.
- Software can adapt to various resolutions and adjust layout size.
- Equipment automatic search connection: need to insert the USB interface of EasyGet WiFi to computer can automatically find the corresponding detector.
- Software supports various application platform online download updates.
- The software supports image zooming down, horizontal and vertical display mode switching.
Mobile terminal interface
Main interface
- Click on the mobile terminal device desktop software shortcut , Enter the software main interface.
- When using the device measuring button or the software measuring button to take the result, the main interface shows the zoom diagram, as shown in the figure below.
View images
As shown in the figure, click “view picture” to enter the list of images, and
the list shows the image information including: picture name, time of
shooting, picture size. Pictures can be deleted and shared.
View data
As shown in the figure, click aredw picture” to enter the list of images, and
the list shows the image inforce. The low post is bright, the mioff after a
certain time. In Open the data file and share the function in the upper right
corner of the file to share the data file.
View report
As shown in the figure, click “View report” to enter the report file list,
click the file name to swipe left to delete the file, and click the file name
to open the data file. Open the report file and share the function in the
upper right corner of the file to share the report file.
Brightness Settings
As shown in figure, click “Brightness Settings”, the video interface display
progress bar of brightness.
Reset Brightness
As shown in figure, click “Brightness Settings”, the video interface display
the default brightness.
General settings
As shown in the figure, click “General Settings” to enter the normal Settings interface. The interface includes the setting: Sound of capture close by default; File name, default File, customizable; Save data, default on; Save report, default on; Company, default Dimension, will be saved in the report; The operator, the default Operator, will be saved in the report.
About us
Click “About us” to enter into our interface, the interface includes: the
company LOGO, software name (EasyGetWifi), software version name, the
company’s website and other information.
Mobile terminal software operation instructions
WIFI connection
The name of the WIFI connection is the device EasyGet_S/N, and the default password is 12345678. The mobile terminal can connect to the EasyGetWiFi device normally when the WIFI switch is switched on and the WIFI indicator is green. When the WIFI connection of the mobile terminal is successful, the software can be used and operated on other auxiliary
WIFI disconnect
When the WIFI connection is disconnected, enter the software, and the main
interface indicates “Wi-Fi connect failed!”, and the software main interface
has WIFI convenient setting button “Wi-Fi setting “. WIFI disconnects, the
software can view the relevant information, software related settings cannot
operation, set up at this time for the operation, such as clicking the “Taking
pictures button”, the software will prompt “The device is not connected.
Please check the connection status” as shown in figure. 
Measure
The software interface measurement button and the body measurement button can
trigger the measurement. The comparison before and after measurement is as
follows:
View zoom
View supports two-touch mode, the image zoom display. Enlarge and Shrink down
as shown below:
Screenshot sound
Slide the left side of the screen, enter the side of the slide, click “General
Settings”, open the “Sound of capture”, there is a voice prompt when take
pictures screenshots.
Delete data, report file
Long press the data, report file to the left to delete.
Share data, report file
Share the data in the top right of the report file for sharing.
Contact us
For machine troubleshooting, maintenance, equipment consulting, and troubleshooting, please contact Dimension Technology Co., Ltd.
- Tel: +86-755-26480850 / 26471436 / 26471446
- Fax: +86-755-26480895-0
- E-mail: sales@weidujs.com
- URL: www.weidujs.com
- Address: 3F, Minlida industrial park Honghualing industrial zone, Liuxian Blvd, Xili Town, Nanshan District, Shenzhen, China.
East China Office
- Telephone: +86 21-36532952
- Fax: +86 21-36532952
- E-mail: mengq.fan@weidujs.com
- Address: Room 1809. Tapu Road No. 306, Putuo District, Shanghai City.
South West China Office
- Tel: +86 28-83198070
- Fax: +86-755-26480895-0
- E-mail: sales.xn@weidujs.com
- Add: 4F, Derun Science and Technology Park, No.2 Xingsheng West Road, Jinniu District. Chengdu, china.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>