BOOMIN BELTS Wireless Belt Buckle Speaker User Manual

BOOMIN BELTS Wireless Belt Buckle Speaker User Manual

What’s in the Box?

Sizing Instructions

1. Sizing Instructions Open thealhgatorteethtoremove ~ the end of the belt
2. Mea,u,e,nd mo,kleogth of the bolt ..
3. OJt the belt to the correct size (j
4. (Optional) HHt seal t he f!nd oft~ belt to reduoe bell fray
5.  Insert end of the belt into the alligator teeth and clamp down.

Cut-to-Flt Adjustable Belt.

Introduction

Introducing Boomin Belts, where style and music meet!
The world’s first Bluetooth belt buckle speaker is a state-of-the-art device that is magnetic, lightweight, and water-resistant, allowing you to listen to your favorite music anywhere. With the added benefit of interchangeable buckle faceplates, you can easily customize your belt’s appearance to match your mood and fashion sense.
The adjustable belt and our proprietary magnetic buckle, with an easy on/off locking system, make it comfortable and convenient to wear and remove. Boomin Belts is the perfect accessory for anyone who wants to enjoy music while keeping their style game on point!

Connect to Bluetooth Device

Please Noted :

1. When the Power is on, Bluetooth mode enables automat ically.
2. Bluetooth will be disconnected if the speaker is switch to SD card mode.

Bluetooth Speaker User Instructions

Charging

During use when the battery is getting low, you will hear a voice prompt saying “Battery Low”. When the battery power is below 3.1V, Bluetooth will
automatically shut down.

Music Transmission

Music Transmission

Use type C data transfer cable to connect Bluetooth speaker and laptop/PC , copy/ download music into the SD card .

Factory Data Reset/ Clearing the Pairing List

Long press+ and – button at the same time for 3S , Clearing the paring list, comes with voice Power off

Voice Prompt

Specifications

Size: 95×25.5×52.7mm Weight: 89g Charging port: TYPE-C Keys: Three (volume up, next/minus, previous and MFB keys).
Battery type: rechargeable lithium polymer battery 3.7V/600mAh Charging specification: DC 5V/500mA Charging overcurrent/overvoltage/overtemperature/voltage over 6.2V and current over 600mA disconnect charging
Temperature: 0-45 degrees Charge. Standby time: 90 Days Voice Talk Time: 8 hours Music Playtime: 6 hours (varies by volume level and audio content)
Battery charge time: 2 hours Output power: 3 watts Signal-to-noise ratio: 85dB Distortion: 1%. Bluetooth version: AC6965E-V5.3 Support Profile: MP2, MP3, WMA, APE, FLAC, MC, MP4, M4A, WAV, AIR AIFC Transmission Range (Hz): 2.402GHz-2.48GHz 4G memory card: Download to speaker via type-C. Pass: 0000 RF transmission: Class!! (-6dBm-+4d8m) Receiving sensitivity: -85dBm Transmission Range (Hz): 2.402GHz-2.48GHz Launch distance: Approx.10m Speaker specification/method: 022mm/anti-magnetic Magnetic iron type: NdFe-B Nb-Fe-Be Distortion: 1% or less Impedance: 40/3W Frequency (Hz): 201-1z-20KHz

MIC specificat ion: ¢4.0’1 .Smm

MIC sensitivity: -38±3dB
MIC impedance: :s2.2kn
MIC working voltage: 3.0V
MIC frequency response: 1 OOHz-1 O,OOOHz

WARNING;

To protect battery lifespan, fully charge at least once every 3 months. Battery life will vary due to usage patterns and environmental conditions. Do not expose the Boom in Belt to liquids wit hout removing cable connection. Do not expose the Boom in Belt to water while charging,
It may result in permanent damage to the speaker or power source. Chemicals, salt or “foreign particles• in your pool or the ocean can damage the seals or harm the connector surface over t ime if not rinsed off after use.
After a liquid spill or rinse, do not charge your speaker until it ‘s completely dry and dean. Charging when wet might damage your speaker: When using an external adapter, the output voltage/current of the external adapter should not exceed 2.4V/0.0025A.

FCC Caution䱁

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will notoccur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• onnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>