EZONTEQ SD6075 Frameless Shower Doors Instruction Manual

EZONTEQ SD6075 Frameless Shower Doors

Specifications:

• Product Name: Shower Door (Model: SD6075)
• Dimensions: 60 inch (width) x 75.5 inch (height)

Product Usage Instructions

Tools Required:

• Soft Cloth or Blanket
• Caulk
• Tape Measure
• Pencil
• Phillips Screwdriver
• Safety Glass
• Level

Other Tools May Be Required:

• Caulk Gun
• Drill
• Hammer
• Mitter Saw or Hacksaw

Installation Steps:

Step 1: Assembly of Support Rods and Guide Rail Bracket

1. Determine a suitable location and place the stainless steel Stopper (C) and Guide Rail Bracket (A) on the support rods.
2. Use the Allen key (S) to loosen the screws on the Guide rail bracket (A).
3. Fix the components in the approximate positions as shown in the figure.

Step 2: Placement of Stationary Glass

1. Place the Stationary Glass (H) and align the holes with the Glass Bracket (B) fixed on the support rod.
2. Cover the Glass Bracket (B) to lock the glass, ensuring proper protection with spacers.

Step 3: Installation of Stationary Glass and Upper Guide Rail

1. Place Stationary Glass (H) with Upper Guide Rail (E) on the installation position.
2. Ensure everything is leveled and mark positions for drilling holes for Wall anchors (O).

Step 4: Final Fixation

1. Fix the Guide Rail Bracket (A) to the wall on both sides with appropriate screws.

FAQ:

• Q: What should I do if I encounter difficulties during assembly?
  A: If you face any challenges during assembly, please contact us for assistance.

• Q: Can the shower door be adjusted for different opening sizes?
  A: The shower door is designed to fit standard openings. For custom sizes, please consult with a professional installer.

If you have any questions about the shower door, please feel free to contact us.

OVERVIEW

IMPORTANT
PLEASE READ BEFORE YOU COMMENCE ASSEMBLY
Follow the guidelines in this user guide to ensure correct assembly and care for this product

SPECIFICATIONS

EXPLODED VIEWS

TOOLS REQUIRED

PART LIST

Installation steps

How To Assemble Shower Door

• Step 1: Determine a suitable location and place the stainless steel Stopper (C) and Guide Rail Bracket (A) on the support rods as shown. Use the Allen key (S) to loosen the screws on the Guide rail bracket (A). First put (C) on the stainless steel support rod and fix it in the approximate position as shown in the figure, Then place (A) on both ends of the stainless steel support rod. Then disassemble the Glass Bracket (B) as shown in figure e, and fix half of it at the small hole of the stainless steel support rod

• Step 2: Place the Stationary Glass (H), align the hole above the glass with the Glass Bracket (B) that has been fixed with the stainless steel support rod. Cover the other half of the Glass Bracket (B) to lock the glass (two spacers are placed separately to protect the glass).
  NOTE: Never set your glass down directly onto a tile or concrete floor. Always use a piece of wood or cardboard and leave the corner pads on the glass until it becomes necessary to remove them to protect the bottom edge and the corners of the glass from breakage

• Step 3: Put Stationary Glass (H) together with the Upper Guide Rail (E) on the installation position. Make sure all are leveled. Determine the distance between the bottom of the Guide Rail Brackets (A) and the ground at 184- 184.5cm, as shown in the figure. Mark the position of the bottom of the Guide Rail Brackets (A) on both sides. Drill holes in the determined position and apply silicone into the holes, insert the Wall anchors (O) for the Guide Rail Bracket.

• Step 4: Fix the Guide Rail Bracket(A) to the wall on both sides with 5*40 screws (M) as shown in the picture. The other side of the Guide Rail Bracket (A) is installed in the same way. Finally, remove the B part of the Guide Rail Brackets (A) and insert it into the Upper Guide Rail (E).

• Step 5: Place the Stationary glass (H) back into the designated position. Slide the Guide Rail Bracket (A) to the two end sides of the Upper Guide Rail(E). Tighten the set screws on the Guide rail bracket (A) with Allen Key (S) to secure the guide rail to the wall.

• Step 6: Install Glass Door Loosen the Rollers (D) screws and Install the rollers. The Upper roller part is used to connect to the Upper Guide Rail (E) and the lower two parts are used to connect to the Glass Door (R).

• Step 7: Hang the Glass Door (R) installed with rollers, to the Upper Guide Rail (E). Slide the Guide Block (L) to the bottom of the glass door. Mark down the predrilled position of the guide block. Set the glass door aside. Now drill the hole with drill bit to the threshold. Put the silicone to the hole and then put the wall anchor (P) into the hole. Now secure the guide block to the threshold with Screw M4X30 (K).

• Step 8: Hang the Glass Door (R) back to the Upper Guide Rail (E) , and slide the bottom of the glass door into the slot of the Guide Block (L) . Be careful that the glass door should not touch the metal part of the guide block.

• Step 9 : Slide the Side Anti-Water Strip (J) to the Glass Door (R), and slide the 2 pieces of Anti-Water Strips (I) with an extended side to the middle glass, cut the extended side that interferes with the Upper Guide Rail (E). Before installing the Anti-Water Strip (I) and Side Anti-Water Strip(J) , lubricate the surface with water to avoid damaging the explosion-proof film.

• Step 10: Install the Anti-Splash Threshold (Q) in front of the Glass Door (R). Put the Antisplash threshold in front of the Glass Door (R), and then put the Aluminum Cover with slot(N) into the Stationary Glass (H), on top of the threshold. Mark down the predrilled holes on the threshold, drill the holes with drill bit, and put the wall anchor (P). Put silicone sealant to the bottom of the Anti-splash threshold, secure it to the threshold with M4x30 Screw (K) and put the covers back on it
  Note: Please choose the right direction of the aluminum cover with slot(N) installation according to the direction of the installed shower door, only in the middle of the two pieces of glass can be installed

• Step 11: Put the anti-jump buttons removed from step a on step 7 back into the Rollers (D) section

• Step 12: Tighten the fasteners on both Rollers (D), Guide Rail Brackets (A) Cover, Glass Brackets (B) and Glassdoor Stoppers (C). The Glassdoor Stoppers (C) can adjust the tightness to move the position, used to block the Rollers (D), control the edge of the glass will not touch the wall, and determine the position before tightening.

• Step 13: Install the handle as shown in the figure.
  NOTE : The connector of the big head on the handle is above

• Step 14 : Apply silicone sealant on the seams between the stationary glass and the shower base/bathtub and between the wall and the stationary glass.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>