HOME DECORATORS COLLECTION HDP00766 Lampson 2 Light Medium Wall Lantern User Guide

**HOME DECORATORS COLLECTION HDP00766 Lampson 2 Light Medium Wall Lantern User Guide

**

IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not continue the assembly process. Please call our Customer Service Team at 1-800-986-3460.

Safety Information

• Consult a qualified electrician with any electrical questions you may have.

Warranty

5-YEAR LIMITED WARRANTY

WHAT IS COVERED

The manufacturer warrants this lighting xture to be free from defects in the materials and workmanship for a period of ve (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modications, alterations, neglect or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, assembled, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship.

WHAT IS NOT COVERED

This warranty shall not apply to the nish on any portion of the product due to weathering, as this is considered normal wear. The manufacturer does not warrant and specically disclaims any warranty, whether expressed or implied, other than the warranty contained herein. The manufacturer specically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to, any labor or expense costs involved in the replacement or repair of the product.

Contact the Customer Service Team at 1-800-986-3460 or visit www.HOMEDEPOT.com/HOMEDECORATORS.

Pre-Installation

PLANNING INSTALLATION

Read all instructions before assembly.

To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard. Inspect each part for defects that may have occurred during shipping. Keep your receipt and these instructions for proof of purchase.

NOTE: This light fixture requires the use of two 120V, 60Hz, 60-Watt max., candelabra-base type B bulbs (not included). Do not exceed the recommended wattage.

TOOLS REQUIRED

• Safety goggles

• Phillips screwdriver

• Flathead screwdriver

• Pliers

• Wire strippers

• Wire cutters

• Ladder

• Electrical tape

• Silicone

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

Installation

Disassembling the light fixture

• Carefully unpack the fixture and lay out all parts on a clean surface.
• Remove the mounting plate (BB) and two rubber washers (FF) from the lantern body (A) by unscrewing two mounting screws (DD).

Installing the mounting plate

DANGER: Ensure the power is off at the main fuse box prior to beginning installation.

• Turn off the switch at the wall.
• Turn the power off at the main fuse box.
• Attach the mounting plate (BB) to the outlet box using the outlet box screws (CC).

Connecting the wires

• Install the fixture bare copper ground wire (1) under the ground screw (EE) on the mounting plate (BB).
• Connect the fixture bare copper ground wire (1) to the green (or bare, or green and yellow) supply ground wire (2) in the outlet box using a wire nut (AA).
• Connect the white fixture wire (3) to the white (or ribbed) supply wire (4) in the outlet box using a wire nut (AA).
• Connect the black fixture wire (5) to the black (or red, or blue) supply wire (6) in the outlet box using a wire nut (AA).

Mounting the fixture body

• Push all excess wires into the outlet box.
• Align the holes in backplate with the holes in mounting plate (BB), and then secure the xture body (A) to the wall with two rubber washers (FF) and two mounting screws (DD).

Installing the bulbs

• Prior to installing the bulbs, inspect sockets for silica packets. If packets are present, then remove and throw away. Do not expose to children or pets.
• Install two 120V, 60Hz, 60-Watt max., candelabra-base type B bulbs (not included) into the sockets (B) of the light fixture.

Sealing the mounting surface

• Apply silicone or RTV compound (not included) between the edges of the fixture body (A) and wall.

Care and Cleaning

• Clean the light fixture with a soft, dry cloth. Do not use any cleaners with chemicals, solvents, or harsh abrasives.

Troubleshooting

• The bulb is burned out

|

• Replace the light bulb.

• The power is off

|

• Ensure that the power supply is turned on

• There is a faulty wire connection

|

• Ensure that the circuit breaker is set in the on position.

• The circuit breaker is off.

|

• Discontinue use of the light ­xture.
• Contact a quali­ed electrician or call the Customer Service Team at 1-800-986-3460.
• Unplug other items on the circuit.

The fuse blows or a circuit breaker trips when the light is turned on.|

• There is an exposed wire.
• There are too many items on one circuit.

|

• Discontinue use of the light ­xture.
• Contact a quali­ed electrician or call the Customer Service Team at 1-800-986-3460. □ Unplug other items on the circuit.

Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service 8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m.- 6 p.m., EST, Saturday 1-800-986-3460

HOMEDEPOT.COM/HOMEDECORATORS

Retain this manual for future use.

References

• Home Decorators Collection - Home Decor - The Home Depot
• Home Decorators Collection - Home Decor - The Home Depot

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>