TRUEFREE HQY003 O1 Wireless Headphones User Guide

TRUEFREE HQY003 O1 Wireless Headphones

Product Information

The product is made by Shenzhen Yuankeji Youxiangongsi and is located at Longhuajiedaosalienshequ Chuangyelu 19haogongcunxinchengshangyezhongxin (Huihaiguangchin) B zuo 13ceng 130, Shenzhen, Guangdong, China 518109. The product is sold underthe brand name “Soundpeats”. The product complies with FCC ID: 2A5BOHQY003 FCC ID:2A5BOHQY003A and IC : 28277-HQY004 IC 28277-HQY004A standards. The product is made in China.

Product Usage Instructions

To use the product, follow the below instructions:

1. Make sure the product is fully charged before use.
2. Turn on the product by pressing the power button.
3. Pair the product to your device via Bluetooth. To pair, enable Bluetooth on your device, search for available devices, and select the product from the list of available devices.
4. Once paired, you can use the product to listen to music or take calls.
5. To adjust the volume, use the volume controls on the product or on your device.
6. To turn off the product, press and hold the power button until the LED light turns off.
7. Store the product in a cool and dry place when not in use.

Pairing

1. Open the charging case cover, take out the earbuds and remove the insulating film on them, then put the two earbuds back into the charging case. Press and hold the button inside the charging box for 3 seconds until the indicator light flashes white. At this time, the indicator light on one earbud flashes red and white alternately, the indicator light on another earbud stays white, and then two earbuds enter the pairing state.
2. Turn on your device’s Bluetooth and select TRUEFREE O1 from the Bluetooth list to complete the pairing.
   After the first time use, open the lid of charging case, earbuds will turn on and connect the phones automatically.

Pairing Two Devices

TRUEFREE O1 can be paired and used with two devices at the same time. The method is: after the earbuds are paired with Device A, turn off Device A’s Bluetooth.
Next, repeat the pairing operation to connect the earbuds to Device B. After connecting Device B successfully, turn on Device A’s Bluetooth,then you can use the earbuds with two devices at the same time.

Reset

Open the charging case cover,

1. Place the earphones back into the charging case, and make sure they are correctly placed.
2. Keep the charging case lid open, and press and hold the button on the charging case for 10 seconds until the lights in the charging case flash white twice, and the reset is complete.
3. Close the charging case lid and re-open it, the earphones are activated.

Wearing

1. Identify the left earphone and the right earphone.
2. Adjust the earphones to fit your ears.

Product Diagram

Control

Q&A

Q1: What does the indicator light of the charging case display?

1. The battery power of the charging case:
2. When charging the charging box, the indicator light shows:

Q2: How to charge the charging case?

1. Connect the charging case to a Type-C charger. (The current does not exceed 1A).
2. If the earphones stay idle for an extended period, charge them at least every three months to prevent the battery from being damaged.

Q3: Why are the earphones still connected to the phone when they are put back to the charging case and the case lid is closed?

1. Check whether the charging case has battery power. If it has run out of battery, closing it will not disconnect the earphones from the device.
2. Make sure the earphones are properly placed in the charging case and the charging contacts on the earphones and charging case are all clean. Please use a soft cloth and a bit of alcohol to clean the contact points on the earphones and the charging case.

Q4: How to disconnect the earbuds from the phone?

• Method 1: Put the earbuds back into the charging case and close the lid of the charging case, the earbuds will automatically turn off and disconnect.
• Method 2: Turn off the Bluetooth on phone to disconnect.
• Method 3: Put the earbuds back into the charging case, press and hold the button inside the charging case for 3 seconds, and the earbuds will disconnect from the current phone and enter the pairing state.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

IC ID
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.”

RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

MANUFACTURER
Shenzhen Guangdong 518109 China
support@soundpeats.com
www.soundpeats.com
FCC ID : 2A5BOHQY003
FCC ID :2A5BOHQY003A
IC : 28277-HQY004
IC： 28277-HQY004A
MADE IN CHINA

References

• SOUNDPEATS Wireless Earbuds, Bluetooth Headphones, Speakers for Sound.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>