GARMIN Dezl‎ 200 Premium 2 in 1 Trucking Headset Owner’s Manual

GARMIN Dezl‎ 200 Premium 2 in 1 Trucking Headset

Getting Started See the Important Safety and Product Information guide in the product box for product warnings and other important information.

Device Overview

 Microphone boom| Move the microphone boom to the vertical position to mute the microphone.  Move the microphone boom left or right to enable the microphone and change the headset orientation.
---|---
 Power button| Press to turn the device on or off.
 USB power port| Connect a USB power cable to charge the headset.
 3.5 mm audio jac| k       Connect a 3.5 mm audio cable.

Bluetooth®  button

| Hold to enter Bluetooth pairing mode. Press to connect to the next paired device.
 ANC button| Press to enable or disable active noise control.

Rocker

| Move up to increase the volume. Move down to decrease the volume.

Hold up to move to the next audio track.

Hold down to move to the previous audio track. Press to play, pause, or resume media.

Press to answer incoming calls or switch to a second call. Press and hold to hang up a call.

 Garmin®  button| Press to activate OK Garmin voice commands with a paired navigation device. Hold to activate the voice assistant on your smartphone.
 Earcup release bu| tton Press to remove the earcup (dēzl Headset 200 only).

Charging the Device

WARNING
This device contains a lithium-ion battery. See the Important Safety and Product Information guide in the product box for product warnings and other important information.

NOTE: The device does not charge when outside the approved temperature range (Specifications, page 14).

1. Plug the small end of the USB cable into the USB port on the headset.
2. Plug the large end of the USB cable into a power source, such as a USB wall charger or a computer USB port.
3. Charge the device completely.

The status LED flashes green while charging. The status LED is solid green when charging is complete.

Turning the Headset On or Off

• To turn on the headset, hold the power button for three seconds.
• To turn off the headset, hold the power button until a tone plays and the headset turns off.

Turning Active Noise Control On or Off
To turn on active noise control, press ANC

A tone plays and the ANC LED turns on. To turn off active noise control, press ANC again. A tone plays and the ANC LED turns off.

Media Controls

You can use the rocker to control the headset volume, music playback, and phone calls. You can move the rocker up and down, and you can press it like a button.

• Move the rocker up or down to increase or decrease the volume.
• Hold the rocker up to play the next audio track.
•  Hold the rocker down to play the previous audio track.
• Press the rocker to play, pause, or resume audio playback.
• Press the rocker to answer incoming phone calls from your paired smartphone.
• Press the rocker to switch to a second active call.
• Press and hold the rocker to hang up a call.

Microphone Controls

You can move the microphone boom to either side to turn it on. If you have a stereo headset model, the left and right orientation of the headset adjusts automatically to match the direction of the microphone. You can move the microphone boom to the “up” or vertical position to mute the microphone.

Removing the Earcup
You can remove an earcup from the stereo headset to keep one ear open while you drive. NOTE: The removable earcup is available only on the dēzl Headset 200.

1. Press and hold the earcup release button .
2. Pull the earcup off of the headset.

Pairing with Your Smartphone

You can pair your dēzl headset with your smartphone and the dēzl app. You can also pair the dēzl app with a compatible Garmin dēzl navigation device to enable advanced Garmin voice-activated navigation through your headset.

1. From the app store on your smartphone, install the dēzl app.
2. Turn on your dēzl headset, and place the headset and your smartphone within 3 m (10 ft.) of each other.
3. On your smartphone, open the dēzl app.
4. On the headset, hold until the blue LED flashes.
5. From the dēzl app, select Garmin dēzl Headset.
6. Follow the on-screen instructions on your smartphone to finish setting up your headset.

**** The main app dashboard appears. After the devices are paired, they connect automatically when they are turned on and within range.

Voice Assistant Features

NOTE: Voice assistant features are not available for all languages and regions. Voice assistant features allow you to use your smartphone or a compatible Garmin navigation device by saying words and commands.

Tips for Using Voice Commands

• Speak in a clear voice.
• Respond to voice prompts from the device as needed.
• If you do not receive a useful response, try rephrasing your request.

Launching Garmin Voice-Activated Navigation
If you pair your headset with the dēzl app and a compatible dēzl navigation device, you can use Garmin voice-activated navigation features. Garmin voice- activated navigation allows you to use plain language spoken requests to search for locations and addresses, start routes with turn-by-turn directions, and more.

• Press GARMIN , and make a spoken request.
• Take me home.
• Where’s the library?

Placing a Phone Call Using Your Headset
You can use your headset to call a contact from the phone book of your paired smartphone.

1. Move the microphone to the forward position.
2. Press GARMIN.
3. Say Call, and say the contact name.

Using the Voice Assistant on Your Smartphone
You can activate the voice assistant on your smartphone using your dēzl headset.  Hold GARMIN for three seconds.

A tone plays and your phone’s voice assistant activates.

Settings

The settings for your dēzl device are configured using the dēzl app. Before you can configure settings, you must pair your device with the dēzl app (Pairing with Your Smartphone, page 9).

Device Maintenance

Updating the Software Using the Garmin dēzl App
When an update is available, the dēzl app sends it to the headset automatically. The next time you start your headset, it notifies you that it is installing an update. Do not turn off your headset while the update is installing. After the update is complete, the headset restarts and operates normally.

Garmin Support Center
Go to support.garmin.com for help and information, such as product manuals, frequently asked questions, videos, and customer support.

Device Care

• Avoid extreme shock and harsh treatment, because it can degrade the life of the product.
• Do not use a sharp object to clean the device.
• Avoid chemical cleaners, solvents, and insect repellents that can damage plastic components and finishes.
• Do not store the device where prolonged exposure to extreme temperatures can occur, because it can cause permanent damage.

Cleaning the Outer Casing
Avoid chemical cleaners and solvents that can damage plastic components.

1. Clean the outer casing of the device using a cloth dampened with a mild detergent solution.
2. Wipe the device

Device Information

Status LEDs

1. The ANC LED ,
2. the Bluetooth LED , and the power LED
3. show the headset status.

or the tempera­ ture is too high for the headset to operate.
Flashing red| The headset battery is low.
Off| The headset is turned off or does not have power.

Specifications

Troubleshooting

My headset battery does not charge

• Verify the headset is receiving power from the connected USB cable. The power LED flashes green while the headset is charging.

• Inspect the power LED (Status LEDs, page 13).
  If the LED is red, the headset is receiving voltage that is too high from the connected power source, or theheadset temperature is too high to operate. OK Garmin voice commands do not work If you have paired your phone and headset, but some features do not work, you can take these actions to resolve the issue.

• In the app store on your smartphone, update the dēzl app to the most recent version.

• Verify the dēzl app on your smartphone is paired with both your headset and a compatible dēzl navigation device.

Left and right audio channels are reversed
The dēzl headset determines the orientation of the audio channels automatically based on the last position of the microphone boom. Turn on the headset, and move the microphone boom to the forward position. The audio channels reset automatically.

Resetting the Headset to Factory Default Settings
You can reset your headset to the factory default settings. Resetting clears all data from the headset.

1. Turn on the headset.
2. Hold GARMIN and for five seconds. The LEDs flash while the headset resets.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>