Wingbo WBCF-BS16-BK 60 Inch DC Ceiling Fan with Lights and Remote Control Instruction Manual

October 30, 2023
WINGBO

Wingbo WBCF-BS16-BK 60 Inch DC Ceiling Fan with Lights and Remote Control

WBCF-BS16-BK 60 Inch DC Ceiling Fan with Lights and Remote
Control

Dear Customer,

Thanks for your purchase!
Should you have any questions or concerns, please do not hesitate to contact us by mail address support@wingbolighting.com

Precautions

Before using this ceiling fan, please read this manual carefully and operate strictly in accordance with the procedures.

  1. The input voltage of this product: 120V/60Hz
  2. If you have insufficient knowledge of electrical appliances, be sure to hire an experienced expert to install them. 3 Before installing and disassembling the ceiling fan light, please turn off the power first. The installation must be installed in the order of ground wire, live wire, and neutral wire. Before disassembly, it must be disassembled in the order of neutral wire, live wire and ground wire to avoid electric shock.
  3. The ceiling fan must be installed on a solid ceiling, and the location of the ceiling fan must be able to withstand a gravity greater than 60 KG.
  4. When installing the ceiling fan, all screws must be securely locked.
  5. When the ceiling fan is rotating, no objects should touch the blades to avoid danger.
  6. The angle and elevation of the leaf frame are determined after many repeated measurements, so it cannot be changed at will. When installing the leaf frame and blades, special care should be taken not to force collisions. If the angle and elevation angle of the leaf frame are deformed that will cause the ceiling fan to shake.

Prepare tools before installation

  • Electrical Adhesive tape

  • 14open spanner

  • Slotted Screwdriver

  • Phillips screwdriver

  • Telescoping ladder

  • Pliers

Basic parameters

  1. Voltage: 120V/60Hz
  2. Power: Motor power: 35W LED power: 18W
  3. Speed + Color change: 6speed+3 color temperatures(Cool white light 6500K+ warm light 3000K+ neutral light 4500K)
  4. Number of rotating leaves: 3 blades
  5. Fan blade material: Solid Wood
  6. Motor material: Pure copper wire winding and high-quality silicon steel stator, high efficiency, super quiet, energy saving.
  7. Control method: Remote control
  8. Diameter: 60inch
  9. Reversible: YES

Installation steps and instructions

  1. Ceiling Fan Kit
    Before the ceiling fan is installed, there are the following accessories in the carton, please check them one by one, if there is no shortage, you can install it.
  • 1*Canopy

  • 1*Decorative cover

  • 2*Downrod

  • 1 *Coupling cover

  • 1 *Mounting Bracket

  • 1*Motor

  • 3*Blades
    Installation steps and instructions

  • 1*Lamp Plate + LED

  • 1 *Lampshade

  • 1 *Screw package

  • 1 Remote control
    1
    Receiver

  • 1*Instruction

Mounting Bracket Fasten Method

  1. Wood ceiling: Drill the mounting bracket directly into the wood ceiling with wood screws (4 pieces) or Use tools to fix the mounting bracket tightly.(The ceiling must bear more than 60KG)
    Mounting Bracket Fasten Method

  2. Concrete ceiling: First use an 08mm hammer drill bit to drill the hole according to the length of the expansion screw, then use the equipped expansion screws (2 Pieces) to fix the bracket on the ceiling, and then tighten the nut of the expansion screw.
    use 8mm drill hole before installing with M6 expansion screws

  3. Install the hanger bracket to the outlet box
    a. Take off the screws on the outlet box.
    b. Install the hanger bracket to the outlet box by screws
    Mounting Bracket Fasten Method

Note:

a. According to the ceiling of different materials, use different screws to fix the mounting bracket (as shown above).
b. After the bracket is fixed, it must be determined to be able to bear the weight of more than 60 kg(test pull by hand) for safety.
c. Ceiling fans cannot be installed on gypsum ceilings.
d. To reduce the risk of fire, electric shock, or personal injury mount to an outlet box marked” Acceptable for Fan Support”. Use the mounting screws provided with the outlet box. Most outlet boxes commonly used for supporting lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

Suspension Installation
  1. Select the downrod
    ①. There are two downrods of 4.5inch and 12inch in the package, customers can choose according to the height of the house.
    ②. The normal default is to install on the 4.5inch downrod.
    ③. How to replace the 12 inch Downrod:
    Notice: Make sure the fan blades at least 7 feet above the floor
    Loosen the two fixing screws (as shown in Figure 2).

    B. Push the downrod upwards (as shown in Figure 3) out of the horizontal tip (as shown in **Figure 4).


C. Then pull out the 4.5 inch downrod to replace another 12 inch downrod (as shown in
Figure 5).

D. After replacement, follow the above installation steps 4-3-2 to install until it is restored to the state shown in
Figure 1.**

E. Finally, you must pay attention that the two fixing screws must be firmly locked.

  1. How to install Suspension Installation
    ①.Remove the positioning screws from the fan body as follows and place them side by side to proceed to the next step (Fig 6)
    Suspension Installation

    ②.Get off the pin off the downrod by remove the R clip, and get the lead wire through the downrod and canopy, then seat the downrod into the fan body & rotate the downrod until the holes on the downrod will match with the holes on the fan body, finally, you should get the pin through the holes and fix the pin by the R clip in another side (Fig 7)
    Suspension Installation
    Suspension Installation

    ③.Tighten the two set screws removed previously.

  2. Hang the fan on the hanger, and then slowly rotate the fan downrod to make the lugs on the hanger fit with the groove of the hanging ball on the down rod. (Figure 9)
    Suspension Installation

Attaching Fan Blades

  1. Take out the blade screws and washers in the hardware bag (as shown in Figure 10 )

  2. Align the blade screw hole with the motor blade plate hole, and tighten the screws in turn (Figure 11)

Note: The solid wood fan blades have a certain squeezing space. The blades must be installed with washers, and pay attention to locking with conventional force. Do not continue to apply force after the blades are locked to continue screwing in the screws, otherwise It will cause irreversible failures to the motor coil!

Install lamp

  1. Remove the three fixing screws from the lamp holder, and lock the lamp plate to the lamp holder with screws. (Figure 12 )

  2. Please check whether the driver output line and the LED source board are tightly inserted, and plug the 2 light wires to the LED board properly.(Figure 13)

  3. Install the lamp shade in place and rotate the lamp shade **clockwise.(Figure 14)

If you fan without light kit, please install the decorative cap to the fan motor. ( Figure 15** )
Attaching Fan Blades

Wiring

*The all-pole disconnect circle breaker with a contact distance of 3mm must be connected to the fixed wiring.

Controller wiring Diagram
Controller wiring Diagram
Wiring

  1. Connected the live wire from ceiling to receiver black wire (AC IN L).
  2. Connected the neutral wire from ceiling to receiver white wire (AC IN N)
  3. Connected the Grey wire (Motor U) from motor to Grey wire(Motor U) from receiver.
  4. Connected the red wire (Motor V)from motor to red wire (Motor V) from receiver.
  5. Connected the yellow (Motor W) from motor to yellow wire (Motor W) from receiver.
  6. Connected the blue wire (FOR LIGHT) from motor to blue wire (FOR LIGHT) from receiver.
  7. Connected the white wire (FOR LIGHT) from motor to white wire (FOR LIGHT) from receiver.

Canopy Installation

After wiring, please loosen the two screws pre-installed on the mounting bracket to match the two holes on the canopy ( Figure 16 )
Canopy Installation

Balance adjustment method of ceiling fan.

If there is any wobble after ceiling fan installation, please confirm whether the screws that fix the hanger ball, mounting bracket, hanger, blade bolder, and blade are locked. If one of the above parts is not locked, please re-lock it.
If it is locked, please adjust it as follows.

  1. Change the position of the fan blades:
    a. There is no improvement after the swap blades position. Please remove the fan blades 2 and 3 and re-lock each other to observe the effect.

  2. Adjust with balance kit.
    A. Take out the balance bag from the package box, use a balance clamp to select one of the fan blades and clamp the balance clamp on the edge of the tail end of the fan blade (Figure 18)

B. Turn on the fan switch to see whether the wobble of the ceiling fan has been reduced. If it does not improve, try another fan blade. Experiment with all the fan blades in turn to find the blade with the weakest clamping balance.
C. Clamp the balance clamp on the fan blade with the weakest wobble, move it in or out on the edge of the fan blade, turn on the ceiling fan to find the best position of the balance clamp to control the wobble balance (Figure 18)
D. Take the balance sticker, tear off the double-sided tape of the balance sticker, and stick the balance sticker on the center of the blade at the position of the balance clip (Figure 18)

Precautions

Warning

In order to prevent fire and electric shock, it is forbidden to install and use the electric switch which is not equipped with this ceiling fan.

Maintenance and repair of ceiling fans

  1. It is recommended to check the connecting parts of the fan are least once a year, such as the hanger, the hanging pipe fastening screw and the fan blade, to ensure that their connection is still safe and reliable.

Ceiling fan troubleshooting Solutions & Common Problems

Can’t st art| 1. Check whether the fuse of the external power line of the ceiling fan is blown, whether the automatic protection switch is tripped and the circuit is broken.
---|---
2. Check whether the voltage is seriously lower than the rated voltage of the ceiling fan.
3. Check whether the internal wiring of the ceiling fan is loose or has poor contact.
Noi se| 1. Ensure the ceiling fan is not severely impacted before installation
2. Make sure that the hanging pipe connecting bolt is installed correctly and the hanging pipe solenoid is locked.
3. The new ceiling fan allows a 24-hour “trial period”, after the trial period, most of the ceiling fan noise will disappear.
4. It is not recommended to install on wooden ceilings, steel structures or prefabricated panels, as this will amplify the sound.
T he lamp i s defective| 1. Check whether the connection wire of the lamp is loose.
2. Check whether the light switch is damaged, the wire end is loose is defective or the contact is poor.
3. Check whether the light source is burned out
Fa n w obble| 1. Check whether the mounting bracket is locked
2. Check if the screw of the lock blade is locked
3. Check whether the screw of the blade retracted to the motor is locked
4. Can it be installed on the inclined ceiling? Yes, pay attention to the inclination angle not exceeding 30 degrees (pay attention to whether the drop ball will press the fan control)

WBCF-BS16~BS21 Series
PLEASE READ AND SAVE THESE INSTRUCTIONS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

WINGBO User Manuals

Related Manuals