Merra CFN-1112 Industrial Fandelier Caged Ceiling Fan User Manual
- October 30, 2023
- MERRA
Table of Contents
**Merra CFN-1112 Industrial Fandelier Caged Ceiling Fan User Manual
**
Introduction
Before beginning installation of this product, read the package list on page 2 and ensure all parts are present and display no defects. If any part is missing or damaged, contact customer service and do not attempt to install the product. Read all of the safety information on page 3 before installation or use.
Estimated assembly time: 120 minutes
Additional tools required for assembly:
Electrical tape, flathead & Phillips screwdriver, pliers, safety glasses, ladder, and wire strippers
Additional helpful tools:
AC tester light, tape measure, wiring handbook, and wire cutters
Package List
| Item | Name | Qty |
|---|---|---|
| A | Mounting Bracket | 1 |
| B | Downrod | 1 |
| C | Canopy | 1 |
| D | Coupling Cover | 1 |
| E | Main Body with Motor, Blades, and Lamp Holders | 1 |
| F | Remote Control | |
| G | Wood Screws | 4 |
| Anchor Bolts | 2 | |
| Wire Nuts | 3 | |
| Metal Washers | 4 | |
| Plastic Anchors | 4 |
Safety Information
Warning!
-
To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning.
-
All wiring must be in accordance with national and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
-
This fan is suitable for use with solid-state speed controls.
-
To reduce the risk of personal injury, use only the fasteners provided with the junction boxfor mounting to the junction box. Most junction boxes commonly used for the support of lighting fixtures are not
acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, & PERSONAL INJURY, MOUNT FAN TO A JUNCTION BOX MARKED “ACCEPTABLE FOR FAN SUPPORT”. -
The junction box and support structure MUST be securely mounted and capable of reliably supporting a minimum of 50 pounds. Use only UL listed junction boxes marked “FOR FAN SUPPORT”.
-
After marking electrical connections, spliced conductors should be turned upward and pushed carefully up into the junction box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the junction box.
-
The fan must be mounted with a minimum of 7 feet clearance from the trailing edge of the blades to the floor.
-
Do not use the reverse switch while the fan blades are in motion. To prevent damage and ensure long use, the fan must be turned off and the blades stopped before reversing direction.
-
Do not place objects in the path of the blades.
-
Exercise caution when working around or cleaning the fan.
-
Use a soft dry cloth to clean the fan body and blades. Do not use water or detergent.
-
The electrical diagrams provided herein are for reference only. Light kits that are not packaged with the fan must be UL listed and suitable for use with this fan. Switches must be UL general use switches. Refer to their separate instructions for proper assembly.
NEVER BEND THE BLADES FOR ANY REASON.
Preparation
-
Turn Off Your Power
Begin installation by removing fuses or turning off circuit breakers to the wiring you will be using. Use your compatible UL listed junction box if you already have one installed.
**** Failure to disconnect the power supply prior to installation may result in serious injury or death. -
Choose Your Mounting Position
If you need to install a new UL listed junction box, secure it directly to your building’s structure usingappropriate fasteners and materials. Do not use plastic boxes. The junction box and its supports must be able to support the MOVING weight of the fan (at least 50 lb.) and be rated for fan support. -
Choose a Suitable Location
Ensure the blades will be at least 30 inches from any obstruction and at least 7 feet above the floor. In locations without a ceiling joist, a hanger support bar may be required. Do not install in damp locations.
Initial Installation
Step 1. Pass the supply wires from the junction box (not included)
through the central hole of the mounting bracket.
Step 2. Secure the bracket to the junction box with the provided
fasteners. Use the mounting screws and metal washers on wood ceilings or the
plastic anchor and anchor bolts on reinforced concrete or similar ceilings.
Downrod Mounting
Step 1. Remove the locking pin and retaining clip from the downrod.
Step 2. Loosen the two locking bolts on the top of the motor assembly.
Step 3. Carefully slide the canopy and coupling cover onto the downrod.
Step 4. Feed the wires of the fan motor assembly through the downrod.
Step 5. Install the downrod onto the top of the motor assembly, aligning
their holes and replacing the pin and the clip.
Step 6. Retighten the previously loosened bolts.
Step 7. Place the downrod’s top mount onto the mounting bracket. Rotate
the entire assembly until the tab has dropped into its slot and sits firmly.
The entire motor assembly should no longer rotate if seated properly.
Failure to reattach the locking pin and/or properly seat the downrod can cause the fan to fall from the ceiling during operation.
DO NOT use the fan before ensuring it is properly secured and the motor cannot rotate.
Circuit Connections
**** Again, ensure that the power has been cut before working with the wiring. Use the wire nuts provided with your fan.
Ensure there are no loose wires or connections, and secure connectors with electrical tape.
Step 1. Connect the 2 colored wires of the receiver to the 2 identically
colored wires of the junction box. Secure each set with the provided wire
nuts.
Step 2. Connect the green or bare copper ground wire of the junction box
to the ground wire of the ceiling fan motor. Separate the white and green
connections from the black wire connections, which should be kept on opposite
sides of the junction box.
Step 3. Tuck all the connections neatly into the junction box.
Canopy Adjustment
Step 1. Remove the locking bolts on the rim of the mounting bracket.
Step 2. Slide the canopy up to the mounting bracket, turning until their slots align with each other.
Step 3. Replace the tighten the bolts.
Light Installation
Install your bulbs into the sockets on the lamp holders. This fixture has been rated for four E12 bulbs (not included) up to 40W each.
Remote Control Operation
Install the remote control holder onto any wall or suitable flat surface using two mounting screws/ bolts.
| Key | Function |
|---|---|
| LOW | Starts the fan at low speed |
| MED | Starts the fan at medium speed |
| HI | Starts the fan at high speed |
| STOP | Stops the f |
| LIGHT | Turns the light on or of |
| 1H | Runs the fan for 1 hour and then turns it of |
| 2H | Runs the fan for 2 hours and then turns it of |
| 4H | Runs the fan for 4 hours and then turns it of |
| 8H | Runs the fan for 8 hours and then turns it off |
Troubleshooting
| Potential Problems | Common Solutions |
|---|---|
| Fan blades don’t rotate | Check fuses and/or circuit breakers and reset if |
needed.
Cut off power to the fan and check its internal electrical connections.
Replace the remote control’s batteries.
Check that the fan cover is correctly placed and no screws interfere with the
movement of the blades.
Contact customer service to replace a faulty remote control
Fan is too noisy| Check that all fasteners are well tightened.
Ensure the canopy housing has a short distance between itself and the ceiling.
Upon initial installation, allow 24 hours of use for the machine to break
itself in.
Cut off power to the fan and check that the wire nut connections are not
rubbing against one another or the inner housing.
If you have installed a solid-state variable-speed control, cut off power to
the fan and disconnect this control from the device. See if using the remote
resolves the problem, which can be caused by erratic signals from such
controls.
Fan wobbles during use| Check that all fasteners are well tightened.
Use the provided balance kit to adjust the blades if their tips are found to
be an unequal distance from the ceiling while well fastened.
Exchange the position of the various blades
Again, do not bend the blades during any of these procedures.
Contact Us
Thank you for choosing our products! If you have any questions or comments, contact us at [email protected] and we’ll resolve your issue ASAP!
For a .pdf copy of the latest version of these instructions, use the appropriate app on your smartphone to scan the QR code to the right.