ENCLO EC18010 4ft H x 3ft W Waverly Outdoor Privacy Fence Panel Screen Instruction Manual
- October 30, 2023
- ENCLO
Table of Contents
- CUSTOMERS INFORMATION
- Detailed Product Dimensions & Specifications
- STEP 1: LAY OUT TOOLS
- STEP 2: LAY OUT MATERIALS
- STEP 3: ASSEMBLE THE PANEL
- STEP 4: INSTALL THE GROUND STAKES
- STEP 5: ASSEMBLE THE SECOND SCREEN PANEL
- STEP 6: INSTALL PANELS IN THE GROUND
- STEP 7: CONNECT THE SCREENS
- CUSTOMERS SUPPORT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ENCLO EC18010 4ft H x 3ft W Waverly Outdoor Privacy Fence Panel Screen
CUSTOMERS INFORMATION
GENERAL INFORMATION
IMPORTANT
- Check the inside of the larger pieces in your box for other materials packed inside.
- When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
- We recommend an area approximately 5’x 8’ for unobstructed assembling.
- You should not need to use excessive force when assembling components.
MISSING OR DAMAGED PARTS?
VISIT OUR WEBSITE FIRST, SO WE CAN HELP YOU RIGHT AWAY!
Although great care has been taken to ensure proper packaging and handling of this product, occasionally problems occur. If you discover any missing, damaged, or defective parts, please visit our website to order replacement parts. If you experience any further trouble with your product, please contact our customer service department.
parts.nychbrands.com
support@encloscreens.com
704-892-5222 / 877-234-6196
Customer service agents are available to take calls weekdays from 9am-5pm EST.
If you call outside of business hours, please leave a voicemail.
To help you quickly and accurately, please have reference item number EC18010 (WHITE COLOR) / EC18011 (CEDAR COLOR) and the specific part name which can be found on page 5. It is helpful if you can provide the batch lot which is a stamped number on the end of the box.
NEED ASSEMBLY HELP?
If you are having problems with the assembly or installation of this product, we are happy to assist you with the process, so please give us a call at 704-892-5222 / 877-234-6196
NEED TO RETURN?
If for some reason you need to return this product, please allow us to help resolve your issues first. If you still decide to return the product, you will need to initiate the return from the company you originally purchased from.
Detailed Product Dimensions & Specifications
STEP 1: LAY OUT TOOLS
Tools required for a smoother installation experience.
-
Drill
-
Mallet*
-
Woold Block*
*- May be needed depending on soil condition
OPTIONAL
-
13/4″ Tulip Auger*
-
Level
*- May be needed depending on soil condition
STEP 2: LAY OUT MATERIALS
-
Ground Stake (4) 3/4″ x 1 1/4″ x 14″
-
Slat (22) .4″ x 2.875″ x 357/8″
-
Rail (4) 7/8″ x 11/2″ x 357/8
-
Left Post (2) 1 1/2″ x 1 1/2″ x 44″
-
Right Post (2) 1 1/2″ x 1 1/2″ x 44″
-
Joiner Clip (2) 1/13″ x 3/4″ x 1 3/4″
-
3/4” Self-Drilling Stainless Steel Screw (28)
STEP 3: ASSEMBLE THE PANEL
STEP 3.1
-
Slide (2) Rails (C) into the routed holes in the Left Post (D).
-
Slide (11) Slats (B) into the angled slots in the left post.
Tip: Brace the left post against a wall or raised flat surface to allow for easier installation in future steps.
STEP 3.2
-
Slide (1) Right Post (E) over the opposite ends of the slats and rails. Ensure the rails and slats are tight to the back of both posts and that the unit is square before driving in screws.
-
Drive (8) total 3/4″ Self-Drilling Stainless Steel Screw (G) into the pre-drilled holes in the posts.
STEP 4: INSTALL THE GROUND STAKES
STEP 4.1
- Slide (2) Ground Stakes (A) up into the bottom of the posts until the pre-drilled holes in the stakes and posts align.
- Drive (4) total 3/4″ self-drilling stainless steel screw into the pre-drilled holes.
STEP 5: ASSEMBLE THE SECOND SCREEN PANEL
STEP 5.1
Repeat Steps 2-3 in order to assemble the second screen.
STEP 6: INSTALL PANELS IN THE GROUND
STEP 6.1
- Move the screen to its final location, and identify the location of the posts.
- Attempt to push the unit into the ground. All 10″ of the ground stakes should go in the ground.
- Ensure the unit is properly leveled.
Note: If you face resistance refer to the instructions in the next step. Excessive force can damage the top of the posts.
STEP 6.2
- If your ground is too hard, loosen the top 6″ or 7″ of the ground with a claw hammer as illustrated.
- Add water to the loosened soil.
- Use a block of wood to protect the top of the post and gently hammer the post into the ground.
STEP 6.3
Optional in hard ground: If your ground is too hard, or you have more than 3 or 4 panels to install, please consider these options:
-
Use a 1¾” diameter auger bit (commonly used for planting tulips) as illustrated ($15-$20 on Amazon.com).
-
Drill a hole about 12” to 16” deep at the desired location, and fill the holes with water as illustrated.
-
Push the panel posts into the holes.
STEP 7: CONNECT THE SCREENS
STEP 7.1
-
Straight Line Application: Connect the screens as shown below using Joiner Clips (F) and 3/4″ self-drilling stainless steel screws.
-
Corner Application: Connect the screens as shown below using Joiner Clips (F) and 3/4″ self-drilling stainless steel screws.
Note: There are no pre-drilled holes for the joiner clips to allow for greater customization during assembly
CUSTOMERS SUPPORT
45 min
Approximate assembly time for 2 screens
Scan the QR
code
for an assembly video
704-892-5222
877-234-6196
6935 Reames Rd. Ste. K.
Charlotte, NC 28216
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>