ENCLO EC18006 Florence Freestanding WoodTek Vinyl Privacy Screen and Planter Box Kit Instruction Manual
- October 30, 2023
- ENCLO
Table of Contents
ENCLO EC18006 Florence Freestanding WoodTek Vinyl Privacy Screen and
Planter Box Kit
GENERAL INFORMATION
IMPORTANT
- Check the inside of the larger pieces in your box for other materials packed inside.
- When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
- We recommend an area approximately 5’x 8’ for unobstructed assembling.
- You should not need to use excessive force when assembling components.
MISSING OR DAMAGED PARTS?
VISIT OUR WEBSITE FIRST, SO WE CAN HELP YOU RIGHT AWAY!
Although great care has been taken to ensure proper packaging and handling of
this product, occasionally problems occur. If you discover any missing,
damaged, or defective parts, please visit our website to order replacement
parts. If you experience any further trouble with your product, please contact
our customer service department.
parts.nychbrands.com
support@encloscreens.com
704-892-5222 / 877-234-6196
Customer service agents are available to take calls weekdays from 9am-5pm EST.
If you call outside of business hours, please leave a voicemail.
To help you quickly and accurately, please have reference item number
EC18006/EC18007 and the specific part name which can be found on page 4. It is
helpful if you can provide the batch lot which is a stamped number on the end
of the box.
NEED ASSEMBLY HELP?
If you are having problems with the assembly or installation of this
product, we are happy to assist you with the process, so please give us a call
at 704-892-5222 / 877-234-6169
NEED TO RETURN?
If for some reason you need to return this product, please allow us to help
resolve your issues first. If you still decide to return the product, you will
need to initiate the return from the company you originally purchased from.
Detailed Product Dimensions & Specifications
Note: For best plant growth, it is recommended to drill (2) 3/4″ diameter
drainage holes in the floor board roughly 12″ apart.
LAY OUT MATERIALS
ASSEMBLY
ASSEMBLING BOARDS
- Lay down (1) Long Board (A) so that the cut grooves face up as shown.
- Place (1) Long Floor Support (D) at the bottom of the long board.
- Position the long floor support so it rests in the middle of the long board.
- Drive (4) 11/2″ Black Self-Drilling Stainless Steel Screws (L) into the predrilled holes in the long floor support.
- Repeat these steps for the second long board.
ASSEMBLING THE PLANTER BOX
-
Orient (2) Short Posts (K) as shown, with two post channels facing each other, and two channels facing front.
-
Slide (1) long board into the post channels, ensuring that the tabs on the posts align with the grooves in the board.
-
Drive (4) 5/8″ black self-drilling stainless steel screws (M) into the predrilled holes in the posts, securing the long board.
Note: Ensure the bottom of the board is flush to the bottom of the posts .
-
Slide (2) Short Boards (B) into the short post channels,ensuring that the board bottoms are flush.
-
Drive (4) 5/8″ black self-drilling stainless steel screws into the pre-drilled holes in the sides of the short posts.
INSTALLING REAR POSTS
- Slide (1) Right Post (G) and (1) Left Post (H) over the short boards so that the partially covered channel on each post faces the front.
- Drive (4) 5/8″ black self-drilling stainless steel screws into the pre-drilled holes in the sides of the posts.
COMPLETING PLANTER BOX
- Slide the second long board into the post channels. Ensure that this board rests flush with the other boards.
- Drive (4) 5/8″ black self-drilling stainless steel screws into the predrilled holes in the posts.
- Fit (3) Short Floor Supports (J) so that the notches fit over the inner walls of the long floor supports as shown.
- Place (1) Floor Board (C) into the planter box, so it rests on the floor supports.
Note: For best plant growth, it is recommended to drill (2) 3/4″ diameter drainage holes in the floor board roughly 12″ apart.
ASSEMBLE THE SCREEN
- Insert (1) Spacer (I) into both the left and right post channel in the orientation shown below. This will create even spacing between the horizontal slats.
- Slide (1) Thin Horizontal Slat (E) into the post channels.
- Slide (7) additional thin horizontal slats, (4) Wide Horizontal Slats (F) and (11) aluminum spacers into the post channels in the pattern shown below. Spacers should be inserted between each horizontal slat.
- Drive (2) 5/8″ black self-drilling stainless steel screws into the pre-drilled holes in the posts, securing the top horizontal slat.
INSTALL POST CAPS
- Insert the (2) Corner Post Caps (N) into the holes in the top of the posts to finish the assembly.
support@encloscreens.com
704-892-5222
877-234-6196
6935 Reames Rd. Ste. K.
Charlotte, NC 28216
www.encloscreens.com
Scan the QR code for an assembly video:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>