UPLIFT DESK ACC087 MoPac Wall Cleat Instruction Manual

October 30, 2023
UPLIFT DESK

MoPac Wall Cleat
ACC087UPLIFT DESK ACC087 MoPac Wall Cleat

Thank you for choosing UPLIFT Desk.

Safety and Warnings

| WARNING! Read all instructions before assembly. Failure to assemble or operate properly may result in damage or personal injury. Retain this manual for future reference.
---|---
| WARNING! Ensure the Wall Cleat is securely mounted to at least 2 wall studs and the cabinet is secured to the wall cleat to prevent a falling cabinet that can cause damage, injury, or death.
| WARNING! Do not exceed a maximum of 50 lbs of contents on or in the cabinet.
| WARNING! Do not climb on or allow children to climb on wall mounted cabinet.
| WARNING! Manufacturer assumes no liability for improper installation or excessive loads placed in or on a wall mounted cabinet.
| WARNING! Ensure the cabinet is unloaded of contents before moving or installing.
| WARNING! Keep all hardware and parts out of reach of children.

PACKAGE CONTENTS

UPLIFT DESK ACC087 MoPac Wall Cleat - PACKAGE

REQUIRED TOOLS

UPLIFT DESK ACC087 MoPac Wall Cleat - TOOLS

•  Stud Finder •  Power Drill
•  Tape Measure •  7/64 Size Drill Bit
•  Level •  Screwdriver
•  Pencil •  4mm Allen Wrench
•  M10 Socket Wrench

NOTES ON WALL CONSTRUCTION

WOOD STUD INSTALLATION
The fasteners provided are intended to mount directly into and NO LESS than two wood wall studs.
Wood studs must be a minimum size of 2” x 4”. The MoPac Wall Cleat was developed to accommodate wall stud spacing of a minimum of 16” on center and a maximum of 24” on center. For additional wall construction types see the following notes.
STEEL STUD INSTALLATION
Fasteners for steel studs are not included. For steel stud installation we recommend use of Toggler brand (Model 50425) or equivalent for anchoring to AT LEAST two steel studs. Steel studs must be at least 25 gauge thickness. Follow installation instructions as outlined by the manufacturer for securing the anchors. These fasteners are not provided.
CINDER BLOCK WALL INSTALLATION
For Cinder Block installation we recommend use of Toggler brand (Model 50425) or equivalent for anchoring to AT LEAST two points. Ensure the anchor is mounted to the hollow section of the block and is not installed in the mortar. Follow installation instructions as outlined by the manufacturer for securing the anchors. These fasteners are not provided.

WALL CLEAT DIMENSIONS

UPLIFT DESK ACC087 MoPac Wall Cleat - DIMENSIONS

ASSEMBLY INSTRUCTIONS

Step 1
A. Upon final installation, the cabinet’s top surface will sit 4-1/4” (108mm) higher than the top edge of the
Wall Cleat. Take this into consideration when planning how high to mount the cleat. Determine the desired location and height from the floor for placing the Wall Cleat.
B. Using a stud finder, determine the location of two studs and mark their location. With a level, ensure the Wall Cleat is level. Using a pencil, mark all locations for mounting through the holes in the cleat.
C. Pre-drill pilot holes through the wall and into the studs with a 7/64” drill bit at the marked locations.
D. Using a M10 socket wrench, fasten the M6x80 Lag Bolts and Flat Washers to the Wall Cleat and into the pre-drilled holes.

UPLIFT DESK ACC087 MoPac Wall Cleat - ASSEMBLY

Step 2
A. Prepare the assembled MoPac Cabinet for wall mounting.
B. Mount the Cabinet Cleat to the back side of the cabinet using the 3 provided M6x30 Flat Head Machine
Screws and Allen Wrench. Be sure to orient the beveled edge of the Cabinet Cleat as shown.
C. Thread 2 of the leveling glides (H5) packaged with the MoPac into the threaded inserts along the back side of the cabinet. Save the remaining leveling glides in case you decide to place the cabinet on the floor in the future.UPLIFT DESK ACC087 MoPac Wall Cleat - cabinet

Step 3
A. With assistance, lift the cabinet onto the mounted Wall Cleat, making sure the Cabinet Cleat is seated securely into the Wall Cleat.UPLIFT DESK ACC087
MoPac Wall Cleat - Cleat

B. If the wall is uneven, rotate either of the leveling glides mounted to the back from Step 2 as needed until the top of the cabinet is level.UPLIFT DESK
ACC087 MoPac Wall Cleat - level

Step 3 Continued
C. To prevent dislodging the unit from the wall, install the two M4x30 Wood Screws through the cabinet and into the Wall Cleat at the locations shown below.UPLIFT DESK ACC087 MoPac Wall Cleat - locations

Step 4
A. If installing additional cabinets repeat Steps 1-3.
B. Use the Side-by-Side Connector hardware (H10 & H11) provided with the MoPac Cabinet for joining multiple cabinets.

UPLIFT DESK ACC087 MoPac Wall Cleat - hardware

© UPLIFT Desk
800-349-3839
512-614-3152
info@upliftdesk.com
upliftdesk.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals