HAULMASTER 66907 1.5 Ton Scissor Jack Owner’s Manual
- October 30, 2023
- HaulMaster
Table of Contents
Owner’s Manual & Safety Instructions
1.5 Ton Scissor Jack
66907 1.5 Ton Scissor Jack
Save This Manual Keep this manual for the safety warnings and precautions,
assembly, operating, inspection, maintenance and cleaning procedures. Write
the product’s serial number in the back of the manual near the assembly
diagram (or month and year of purchase if product has no number). Keep this
manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact and undamaged. If any
parts are missing or broken, please call 1-888-866-5797 as soon as possible.
Copyright © 2022 by Harbor Freight Tools ® . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described
herein.Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
WARNING SYMBOLS AND DEFINITIONS
****| This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this symbol to
avoid possible injury or death.
---|---
| Indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
| Indicates a hazardous situation which, if not avoided, could result in death
or serious injury.
| Indicates a hazardous situation which, if not avoided, could result in minor
or moderate injury.
| Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
-
Study, understand, and follow all instructions before operating this device.
-
Do not exceed rated capacity.
-
Use only on a hard, level surface capable of supporting the load
-
Support the load with appropriate means immediately after lifting.
-
Failure to heed these markings may result in personal injury and/or property damage.
-
Lift only on areas of the vehicle as specified by the vehicle manufacturer.
-
No alterations shall be made to this product.
-
Only attachments and/or adapters supplied by the manufacturer shall be used.
-
Do not exceed rated capacities AT SPECIFIED HEIGHTS. Do not use if Jack cannot extend at least 6″ before lifting load.
-
Do not use blocks underneath or above jack.
-
Use only for emergency tire changing or mounting tire chains.
-
Do not get beneath the vehicle when it is supported by the jack.
-
If vehicle is pushed off jack, discard jack. Do not reuse.
-
Do not use for aircraft purposes.
-
Wear ANSI-approved safety goggles and heavy duty work gloves during use.
-
Keep clear of load while lifting and lowering.
-
Apply parking break and chock tires before using.
-
Lift vehicle only at manu facturer recommended locations.
-
Inspect before every use; do not use if parts are bent, loose, or damaged.
-
Follow tire changing procedure or tire chain mounting procedure specified in the vehicle manufacturer’s owner’s manual.
-
Do not stand on the Jack. Do not have people or pets in the vehicle you are attempting to raise.
-
Do not lift the vehicle more than necessary.
Lifting more than necessary may cause unexpected movement or tipping. Only lift the vehicle until one wheel is off the ground. -
Keep hands and fingers away from joints or jack interior.
-
Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure.
-
Maintain labels and nameplates on tool.
These carry important safety information.
If unreadable or missing, contact Harbor Freight Tools for replacement. -
This product is not a toy.
Keep it out of reach of children. -
The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur.
The operator must understand that common sense and caution are factors which cannot be built into this product but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
For technical questions, please call 1-888-866-5797.
Specifications
Jack Capacity| 3000 lb. extended 14″ or more
1800 lb. extended 10″ or more
1200 lb. extended 8″ or more
900 lb. extended 6″ or more
---|---
Height Range| 3-3/4″ to 15-1/8″
Operating Instructions
Park vehicle on a flat, level, solid, surface safely away from oncoming traffic. Turn off the vehicle’s engine. Place the vehicle’s transmission in “PARK” (if automatic) or in its lowest gear (if manual). Set the vehicle’s emergency brake. Then, chock the wheels that are not being lifted.
-
Assemble the Handle (15) and Rocker Bar (14).
-
Slide the hooked end of the Rocker Bar into the holes in the Rocker Head (13).
-
Attach Handle to the flat end of the Rocker Bar.
-
If the Jack is not fully collapsed, lower the Jack so that it will easily slide under the vehicle.
-
Chock the wheels opposite the wheel to be removed.
-
To make it easier to remove the wheel’s lug nuts.
Slightly loosen the lug nuts prior to raising the wheel. -
Slide the Jack under the vehicle near the wheel being removed.
IMPORTANT: The Scissor Jack is designed for use on vehicle’s with frame seams capable of sustaining rated capacity loads. Carefully position the Scissor Jack under the vehicle manufacturer’s recommended lift point. -
Rotate the Handle clockwise, raising the Jack. Continue rotating the Handle until the vehicle is raised enough so the wheel is approximately 1″ off the ground.
-
Remove the lug nuts from the vehicle’s wheel. Remove the wheel, and replace it with the spare wheel (not included). Replace and tighten all the lug nuts onto the wheel.
-
Remove the old wheel, tools and any other objects from under the vehicle.
-
Rotate the Handle counterclockwise to lower the Jack.
-
Continue rotating the Handle until the Jack is completely collapsed to the ground.
-
Double check and re-tighten the wheel lugs.
-
Remove the Jack.
Maintenance
Procedures not specifically explained in this manual must be performed only by
a qualified technician.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise occurs, have the problem
corrected before further use.
TO PREVENT SERIOUS INJURY:
Remove load from the jack before any procedure on this page.
-
BEFORE EACH USE, inspect the general condition of the equipment. Check for:
• loose hardware
• misalignment or binding of moving parts
• cracked or broken parts
• any other condition that may affect its safe operation.
• lubricate moving parts of the Jack with lubricating oil. -
Before each use and after the inspection, thoroughly test the Scissor Jack for proper operation prior to its actual use.
-
AFTER USE, clean the tool with clean cloth.
-
Store the jack in a safe, dry location out of reach of children and other non-authorized people.
Parts List and Diagram
Parts List
| Part | Description | Qty |
|---|---|---|
| 1 | Jacking Head Rivet | 1 |
| 2 | Jacking Head | 1 |
| 3 | Jacking Head Seat | 1 |
| 4 | Upper Fork | 2 |
| 5 | Nut | 1 |
| 6 | Lower Fork | 2 |
| 7 | Base | 1 |
| 8 | Rivet | 4 |
| 9 | Supporting Axle | 1 |
| 10 | Bearing | 1 |
| 11 | Washer | 3 |
| 12 | Spindle Rod | 1 |
| 13 | Rocker Head | 1 |
| 14 | Rocker Bar | 1 |
| 15 | Handle | 1 |
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase
instead.
Note: Some parts are listed and shown for illustration purposes only, and
are not available individually as replacement parts. Parts may not be
interchangeable. Specify UPC 193175492531 when ordering.
Assembly Diagram
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser
that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to
damage due directly or indirectly, to misuse, abuse, negligence or accidents,
repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no
event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our
product. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation of exclusion may not apply to
you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection verifies
the defect, we will either repair or replace the product at our election or we
may elect to refund the purchase price if we cannot readily and quickly
provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost
of returning the product. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state.
26677 Agoura Road • Calabasas, CA 91302 •
1-888-866-5797
Documents / Resources
|
HAULMASTER 66907 1.5 Ton Scissor
Jack
[pdf] Owner's Manual
66907 1.5 Ton Scissor Jack, 66907, 1.5 Ton Scissor Jack, Scissor Jack, Jack
---|---
|
HAULMASTER 66907 1.5 Ton Scissor
Jack
[pdf] Owner's Manual
66907, 66907 1.5 Ton Scissor Jack, 1.5 Ton Scissor Jack, Scissor Jack, Jack
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>