GRAEF CM1012 Coffee Grinder Instruction Manual

CM1012 Coffee Grinder
Instruction Manual

CM1012

PRODUCT DESCRIPTION

 1 Bean container cap
2 Bean container
3 Slide lock
4 Rotary adjuster for setting the grinding grade
5 ON / OFF switch
6 Activation button – Manual / Timer| 7 Time setting for the timer
8 Mounting screw for the container
9 Outlet
10 Contact switch
11 Group handle holder
12 Protective pad*
---|---

*For a better hold and to protect the group handle, you can stick the enclosed protective pad onto the group handle holder.

PREFACE
Dear Customer,
You have made a good choice by buying this coffee grinder. You have purchased a recognized quality product.
Thank you very much for buying our product. We wish you a lot of pleasure with your new Grief coffee grinder.

INFORMATION ON THESE OPERATING INSTRUCTIONS

These operating instructions are part of the coffee grinder (hereinafter referred to as unit) and provide important information on start-up, safety, intended use and the service of the unit. The operating instructions have to be available at  the unit at all times. The instructions have to be read and applied by every person who in view of:

• Initial operation,
• Start-up
• Operation
• Fault remedy and/or

Cleaning

Keep these operating instructions and pass them on to the next owner along with the unit.
These operating instructions cannot take into consideration every conceivable use. For further information or in the event of problems that are not covered or not covered in sufficient detail in these instructions, please contact Grief customer service or your specialist dealer.

WARNING MESSAGES

In these operating instructions, the following warning messages and signal words are used:

WARNING
This refers to a potentially dangerous situation. Failure to observe this warning may result in serious injury or even death.

CAUTION
This refers to a potentially dangerous situation. In case of non-observation of this warning message, material damage may occur.
IMPORTANT!
This refers to application hints and other especially important information!

GENERAL SAFETY INSTRUCTIONS

This unit is in conformity with the safety instructions mentioned hereinbefore. However, incorrect handling may lead to personal injury and material damage. For safe handling of this unit, please observe the following safety instructions:

• Before using the unit check for any external visible damage of the housing, the connecting cable and plug. Do not operate a damaged unit.
• Repairs may be carried out only by an expert or by Grief after-sales service. Incorrect repairs may cause considerable hazards for the user. In addition, any claim under guarantee is forfeited.
• Defective parts must be replaced by original spare parts only. Only these parts are guaranteed to meet the safety requirements.
• This unit can also be used by children from 8 years age as well as by persons with limited physical, sensory or mental ability or with a lack of experience and/or knowledge if they are supervised or have been trained in using the unit  and have understood the dangers which may result from it. Cleaning and user maintenance must not be carried out by children, unless they are 8 years or older and are supervised.
• The unit and its connecting cable have to be clear of children who are younger than 8 years.
• Children should be supervised in order to make sure that they do not play with this unit.
• The unit is not intended to be used with an external timer or a separate remote control.
• Always disconnect the connecting cable by using plug; do not pull the connecting cable.
• Do not use the unit if the connecting cable or plug is damaged.
• Do not open the housing under any circumstances. When touching live connections and if the electric and mechanical structure is changed, there is danger of electric shock.
• Never touch live parts. They may cause an electric shock or even may lead to death.
• Before connecting the unit, compare the connecting data (voltage and frequency) on the type plate with those of your energy network. These details must correspond so that no damage occurs to the unit.
• Check to be sure that the connecting cable has been safely laid. Due to getting caught on the cable, the unit might fall down from the work surface.
• Packaging materials must not be used for playing. There is danger of suffocation.
• Never use the unit in the vicinity of a heat source.
• Never use the unit outdoors, and always keep it in a dry place.
• To ensure normal operation, the unit must be installed in locations where the temperature ranges from +5°C to +32°C and the humidity does not exceed 70%.
• Do not attempt to grind ground coffee again.
• To avoid overheating the unit, we recommend not keeping on grinding for more than 1 minute.
• Do not block any ventilation or heat sink openings or slots and do not introduce water or liquids of any kind into the unit.
• Never insert spoons, forks or other utensils into the outlet or coffee bean container while the unit is in operation.
• To remove coffee to be ground from the outlet, always switch off the machine first.
• If a foreign object blocks the motor, switch off the unit immediately and contact Grief customer service.

DANGER CAUSED BY ELECTRIC CURRENT

WARNING
Mortal danger is caused by contact with live cables or components!
Please observe the following safety instructions in order to prevent exposure to electric cur- rent:

• Do not use the unit if the connecting cable or plug is damaged.
• In this case, you should let the Grief Customer Service or an authorized specialist install a new connecting cable before re-using the unit.
• Do not open the housing under any circumstances. When touching live connections and if the electric and mechanical structure is changed, there is danger of electric shock.
• Never touch live parts. They may cause an electric shock or even may lead to death.

INTENDED USE
This unit is not intended for commercial use. Use the unit for grinding coffee beans only. Another or any exceeding use shall not be considered intended. This unit is intended for use in a household.

• Staff kitchens in shops and office
• In agricultural estates
• By guests in hotels, motels and other living quarters
• In bed and breakfast boarding houses

IMPORTANT!
Use only in household-like areas!
Another or any exceeding use shall not be considered intended.

CAUTION
The unit can cause dangers, if is not used as intended.

• Use the unit exclusively as intended.
• Observe the procedures described in these operating instructions.

Claims of any kind caused by damage by unintended use shall be excluded.
The risk shall be borne sole by the user.

LIMITATION OF LIABILITY
All technical information, data and notes on the installation, the operation and the care contained in these operating instructions correspond to the last status before printing, and are rendered under consideration of our previous experience and to the best of knowledge. No claims may be derived from the specifications, illustrations and descriptions in these instructions.
The manufacturer does not assume any liability for damage caused by:

• Non-observation of the instructions
• Unintended use
• Improper repairs
• Technical modifications
• Use of unapproved spare parts

Translations are carried out to the best of knowledge. We do not assume any liability for translation mistakes.
The original German text shall be binding only.

AFTER-SALES SERVICE
If your Grief unit is damaged, please contact your dealer or the Grief Customer Service at +49 (2932) 9703677 or write an e-mail to service@graef.de.

IMPORTANT!
If possible, keep the original packaging during the guarantee period of the unit in order to be able to pack the unit properly in case of guarantee.

UNPACKING
When unpacking the unit, proceed as follows:

• Remove the unit from the box.
• Remove the packaging parts.
• Remove any stickers on the unit. Do not remove the type plate!

DISPOSAL OF THE PACKAGING

The packaging protects the unit against transport damage. The packaging materials are selected according to the environmental compatibility and disposal-related aspects and can therefore be recycled. The return of packaging into the  material cycle saves raw material and reduces the waste volume. Dispose of the packaging material no longer needed at collection points for the “Green Dot” recycling system (in Germany).

DISPOSAL OF THE UNIT
At the end of its service life, this product cannot be disposed of in normal domestic waste. The symbol on the product and in the operating instructions point out to this fact. Reuse the materials according to their marking. With the reuse,  recycling or other forms of recycling of old equipment, you  make an important contribution to the protection of our environment. Please ask your municipal administration for the disposal point.

REQUIREMENTS ON THE INSTALLATION LOCATION
For safe and faultless operation of the unit, the following requirements of the installation location have to be met:

• The unit has to be placed on a solid, flat, horizontal, and non-slipping surface with a sufficient weight-carrying capacity.
• Make sure that the unit cannot topple over.
• Choose the location in such a way that children cannot reach the connecting cable of the unit.
• Do not place the unit on hot surfaces, such as hotplates, or near them.
• Never use the unit outdoor and store in a dry location.
• The unit is not designed for installation in a wall or a built-in cupboard.
• Do not set up the unit in a hot, wet or moist environment.
• The socket has to be easily accessible so that the connecting cable can be removed easily in case of emergency.

ELECTRICAL CONNECTION
For safe and fault-free operation of the unit, the following requirements have to be met during the electrical connection:

• Before connecting the unit, compare the connecting data (voltage and frequency) on the type plate with those of your energy network. These details must correspond so that no damage occurs to  the unit. In case of uncertainty,  contact a qualified electrician.
• The socket has to be protected at least by a 10 amps circuit breaker.
• Make sure that the connecting cable is not damaged and not laid across hot surfaces or sharp edges.
•  The connecting cable must not be stretched tightly.
• The electric safety of the unit is ensured only when it is connected to a socket with protective conductor installed correctly. Operation on a socket without protective conductor is forbidden. If in doubt, let the house installation be checked by a skilled electrician. The manufacturer does not assume responsibility for damage which has been caused by missing or interrupted protective conductor.

PRIOR TO FIRST USE
Clean all parts as described under “Cleaning”.
ATTACHING THE BEAN CONTAINER

• Fit the coffee bean container on the unit.
• If necessary, use a flat-blade screwdriver to tighten the lock screw of the container.
• Open the outlet of the coffee bean container by pulling out the sliding lock.
• Remove the cap of the bean container and fill it with coffee beans.
• Fit the cap.

GROUP HANDLE HOLDER
Place the group handle holder. The group handle holder is height adjustable. To find the right position for the group handle, loosen the screw and adjust the height. Do not loosen completely the screws. The group handle holder can be  moved up or down depending on the size of the group handle. When you have found the right size, tighten the screw. The group handle holder fixes the group handle directly under the outlet and allows you to automatically grind into the
group handle without holding it.

SETTING THE GRINDING GRADE

IMPORTANT!
The grain size of the coffee grounds can be varied by means of the different settings of the grinding grade.
Precise data on the grinding grade cannot be given as many different factors play a role, such as type of coffee / bean, room temperature, personal taste, etcetera.
In general, a finer grinding grade is set for Espresso; for filter coffee a medium grinding grade and for French Press a coarser grinding grade.
The unit is equipped with a variable grinding grade adjustment to be set with the rotary knob. Turn it clockwise for a finer grind and turn it anticlockwise for a coarser grind.
Note:

•  The finer the grinding grade, the longer the grinding process.
• If you use a very fine grinding grade, it may happen that the coffee agglutinates.
• Adjust the grinding grade by one or two stages at a time while the coffee grinder is running, otherwise the unit may jam.

DOSE SETTING
The timer can be set using the rotary adjuster on the side of the unit.
Turn the adjuster counterclockwise to shorten the time and grind a smaller amount of coffee grounds.
Turn the adjuster clockwise to extend the time and grind a higher amount of coffee grounds.

START-UP

• Plug the connecting cable into the socket.
• Switch on the unit.

MANUAL:

• Check the Manual/Timer activation button. As for manual grinding make sure that this button is not retained.
• Fit the group handle on the group handle holder. Grinding starts when operating the contact switch.
• Keep that switch pressed for grinding.
•  As soon as the desired quantity has been reached, remove the group handle.

AUTOMATIC:

• Check the Manual/Timer activation button. As for automatic grinding make sure that button is retained.
• Place the group handle on the group handle holder and press it once against the contact switch.
• Grinding starts automatically when operating the contact switch.
• Once the grinding process has started, the time for the current process cannot be adjusted.
• When the set grinding quantity is reached, the grinder stops automatically.

IMPORTANT!
To ensure correct operation of the unit, do not grind more than 160 g coffee beans per grind.
CLEANING OUTSIDE
Disconnect the mains plug from the socket and let the unit cool. Use a soft and moist cloth to clean the outer surfaces of the unit. Use a mild detergent in case of heavy contamination.
Never clean the unit under running water or immerse it into water.

CLEANING
IMPORTANT!
Old coffee remaining in the unit may lead to oxidation. This condition affects the result of the preparation; unpleasant and inedible taste may develop. Keep the unit always in a well-serviced condition in order to ensure perfect Espresso at all times.
Depending on use, clean the unit at least once a week.

• Remove the plug from the socket.
• Close the bean container by pushing the slider in.
• Grind the beans left in the grinder.
• Loosen the lock screw of the bean container.
• Remove the bean container by lifting it upwards.
• Place the unused beans in an airtight container so keep the flavor.
• Clean the coffee bean container and the coffee grounds container in warm water using a little washing-up liquid.
• Dry the container well then.

CLEANING AND MAINTENANCE OF THE GRINDING GEAR
CAUTION

•  Maintenance and cleaning work on the grinding gear may only be carried out by trained persons who are familiar with the maintenance and cleaning of the grinding gear.
• Do not perform any unauthorized maintenance work and always use original spare parts.

1. Remove the cap on the back of the housing.
2. Use a screwdriver to remove the screw.
3. Remove upper housing cover.
4.  After removing the upper housing cover, loosen the three screws fixing the upper grinding gear with a screwdriver and then remove the upper grinding gear.
5. Clean this grinding gear and the other internal parts with a brush or dry cloth. If necessary, use a hoover to remove any remaining coffee powder.
6. After cleaning, replace the upper grinding gear, retighten the three screws from the upper grinding gear with a screwdriver and then close the housing with the upper housing cover.
7. Tighten the screw on the housing with a screwdriver and put on the cap.
   Note:
   You can grind suitable cleaning tablets to clean the lower grinder.

IMPORTANT!
If you notice a change in the grinding results during the life of the appliance, this may be an indication of wear on the grinding discs.
Check the grinding discs for wear every 250 kg of coffee and, if necessary, have them replaced with original spare parts by a specialist or by Grief customer service.

TWO-YEAR WARRANTY
As from the date of purchase we assume manufacturer warranty of twenty four months for defects which can be traced back to manufacturing and material defect. Your legal warranty claim in conformity with Section 437 et seq. of the  German Civil Code (BGB) shall remain unaffected by this regulation. The warranty does not cover any damage which is caused by incorrect handling or use as well as defects which only slightly influence the function or the value of the  unit. Moreover, transport damage insofar we are not responsible shall be excluded from the claims under guarantee. Warranty shall be ruled out for damage, the repair of which has not been carried out by us or one of our representations.  In case of justified complaints, we shall repair the defective product or replace it by a product without defects at our discretion.

   Gebr. Grief GmbH & Co. KG |
Donnerfeld 6 | 59757 Arnsberg | www.graef.de
Stand: April 2023.

References

• GRAEF Onlineshop | GRAEF Onlineshop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>