TESLA Smart Heating Pillow User Manual
- June 4, 2024
- Tesla
Table of Contents
Smart Heating Pillow
User Manual
OPERATING INSTRUCTIONS
1.1 Turn on and Turn off
Turn the on-Connect device to the power turn on.
Turn off: Click the button until the LED light goes out to turn off (Mainly
used to turn off the heating function).
1.2 Temperature Control
This product is designed with four gears, which are displayed below:
1st gear-green light (37~41°C);
2nd gear- orange light (42°C~46°C);
3rd gear-purple light (47°C~51°C);
4th gear-red light (52°C~57°C);
1.2.1 Shift by Button
Users can directly switch gears by the button, and set the corresponding
target temperature cycle control in the order of “starting->green 37°C->orange
42°C ->purple47°C->red 52°C-> shutdowns” The specific operation flow is shown
in the following figure:
Every time the gear is adjusted, the device will be heated to full power. When
the target temperature is reached, the breathing light will be turned on and
kept at a constant temperature.
Note: It can be turned on by plugging in the power supply. By default, it will
be heated at the 1st gear. When the temperature reaches 37°C, the green
breathing light will be turned on.
1.2.2 Temperature Memory
During the normal operation of the device, in case of unexpected power off
(e.g., the mobile power bank is out of power or the AC-DC adaptor is pulled
out, etc.), the controller will store the gear information before power
failure, and then switch directly to the gear to continue heating after power-
up again.
1.2.3 Smart Heating Mode
In any gear, press the button for more than 4 seconds until the LED light
turns red, and then enter the Smart Heating Mode. During this mode, the four
light colors are turned off and on cyclically, with a time interval of 1
second.
In the smart heating mode, first heat for 5 minutes in the 4th gear, then
heats for 10 minutes in the 3rd gear, 15 minutes in the 2nd gear, and 20
minutes in the 1st gear. Enter the standby mode after the above cycle ends.
During this progress, any key operation will immediately exit the Smart
heating mode.
1.3 Lighting Control
1.3.1 Night Mode
This device has a night mode, and if there is no operation within 30 seconds
from 17:00 on the same day to 08:00 on the next day, the lights will be
automatically turned off in order to reduce the impact on the user’s sleep.
After entering the night mode, any key operation or APP operation will cause
the machine to exit the night mode immediately.
1.4 Bluetooth Music Playing
See 1.6.6 Bluetooth music playing for more details.
1.5 Sleep Monitoring
Sleep monitoring is conducted from 18:00 on the same day to 12:00 on the next
day. During this period, sleep data (Mainly related parameters of shallow
sleep, deep sleep, and rapid eye rotation) are recorded every half hour.
In order to ensure the accuracy of sleep monitoring data, please try to:
- Connect the Tesla Smart App with the device before going to sleep at night and enter the “sleep” page
- After getting up the next day, please connect to the APP again and enter the “Sleep” page to synchronize the sleep data.
Note: Sleep data can only be kept on the device side for 3 days, so if
the device is not used to connect to the APP for 3 consecutive days, the data
of the earliest day may become inaccurate or lost. The acquired sleep data
will be displayed on the “Sleeping” page of the APP.
1.6 APP operation
Please search for “Tesla Smart App” in the Android application market (If it
is an Apple phone, please go to Apple Store), download and then install it.
1.6.1 Arrangements
- Log in to the Tesla Smart APP.
- Press and hold the device for 2s, wait for the blue light to flash, and then enter Bluetooth pairing mode.
1.6.2 Search and Connection
- Manual adding method: click“+” in the upper right corner –select “add manually ”–find the device to be added (the device name is “Smart Sleep-assistance Pillow” ), “add it” –Click “+” –wait for connection — after completion, the system will automatically enter the device page.
- Automatic adding method: click “+ ”in the upper right corner — select “ automatic adding” — search for the device (the device name is “ Tesla Smart Heating Pillow”-“Next” –wait for connection — the system will automatically enter the device page after completion.
1.6.3 Temperature Adjustment
Temperature adjustment: The annular area is the temperature adjustment
operation area, and the user needs to slide the pointer to adjust the
temperature. Turn off the heating when the pointer sides off.
Stall: Different temperatures correspond to different gears and colors: green
light(37°C~41°C), orange light(42°C~46°C), purple light (47°C~51°C), and
red(≥52°C).
1.6.4 Timing Heating
Click the “timed heating” button, select the time in the pop-up window, and
then click “OK” to start automatic heating. At the same time, display the
countdown in the middle of the temperature control interface on this page.
After the countdown, the machine automatically stops heating. Click the “close
timing” button to close the countdown and keep the device at the current
temperature.
1.6.5 Sleep Monitoring
Data viewing: On the “Sleep” page, users can view the total sleep duration,
sleep duration, proportion in each stage, sleep quality, and other
information.
Data update: The local data will be automatically synchronized when entering
the device page or the data can be manually switched for synchronization.
Local data can be kept for up to 3days, and data can be kept for up to 7 days
after being uploaded to the cloud.
1.6.6 Bluetooth Music Playing
In “Setting –Bluetooth” of the mobile phone, turn on the Bluetooth function,
search and pair the device named “Smart Music Pillow BLE”.
Sleep Music on Demand
On the “Music” page of the Tuya smart APP, users can order various sleeping
music according to their personal hobbies.
Click the drop-down button, and the user can perform the timed operation and
start the countdown. When the time is set to „∞“, it can be closed at a fixed
time.
1.6.7 Device Information
Device information: Click in the upper right corner to enter the device
information interface, where you can view the device status and more setting
options.
Firmware update: Click “Check Firmware Upgrade”, and the users can view the
device version information. If there is a new version, the users will be
prompted to upgrade.
Technical Specification
| Material | Memory Foam, Cotton, Polyester |
|---|---|
| Temperature Range | 37 ºC – 52 ºC |
| Power | 500mA, USB |
| Functions | Sleep monitoring |
IR Heating
Build in Speakers
Timmer
Washable cover
Package content| High-Quality Memory Foam Pillow
Built-In USB Cable
User Manual
Connection| Bluetooth
Dimensions| 57 x 38 x 8-11cm
App| Tesla Smart for iOS and Android
INFORMATION ABOUT DISPOSAL AND RECYCLING
This product is marked with the symbol for a separate collection. The product
must be disposed of in accordance with the regulations for disposal of
electrical and electronic equipment (Directive 2012/19/EU on waste electrical
and electronic equipment). Disposal together with regular municipal waste is
prohibited. Dispose of all electrical and electronic products in accordance
with all local and European regulations at the designated collection points
which hold the appropriate authorization and certification in line with the
local and legislative regulations. Correct disposal and recycling help to
minimize impacts on the environment and human health.
Further information regarding disposal can be obtained from the vendor,
authorized service center, or local authorities.
EU DECLARATION OF CONFORMITY
Hereby, Witty Trade s.r.o. declares that the radio equipment type TSL-HC-HL60
is in compliance with EU directives. The full text of the EU declaration of
conformity is available at the following internet address:
teslasmart.com/declaration
Connectivity: Bluetooth
Frequency band: 2.402 – 2.480 GHz
Max. radio-frequency power (EIRP): < 20 dBm
Manufacturer
Tesla Global Ltd.
Gee Chang Industrial Building,
121 Des Voeux Road Central
Hong Kong
www.teslasmart.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>