Condair CHR-NA Digital Room Humidistat with Display Instruction Manual

October 30, 2023
condair

Condair CHR-NA Digital Room Humidistat with Display

Digital Room Humidistat with Display

The Condair digital humidistat is a device that measures and controls the humidity level in a room. It comes with an on/off digital wall humidistat that can be installed easily with the help of the installation instructions provided below. The device also allows the user to change and control various parameters according to their preferences.

Installation Instructions

  1. Open the screw of the housing and remove the mounting plate with the connecting unit.
  2. Connect wires of the connection cable to the terminals according to the wiring diagram.
  3. At the place of location fix mounting plate (plastic screw facing downwards) with two screws to the flush-mounting or wall-mounting box (see dimension drawing).
  4. Carefully snap housing onto the mounting plate and fix it with the screw (do not tighten screw too much).

Usage Instructions

Calibration

To calibrate, press the UP key until you see the calibration value and tool symbol on the display. Use the UP/DOWN buttons to calibrate and then press the Save calibration button to save the calibration. The tool symbol will disappear after calibration is saved. Note that disable inputs will not be shown on the display.

Changing Parameters

  1. Press the button simultaneously for three seconds. The display will show firmware version and revision number.
  2. Press the button to start login. The small digits show CODE.
  3. Select correct code (password) using and buttons. Note: Code to access user parameters is 0009. The access codes are fixed and cannot be changed.
  4. Press the button after selecting the correct code.
  5. Once logged in with 0009, the user/display parameters are displayed immediately.
  6. Select the parameters with the or button. Change a parameter by pressing the button. The symbol is displayed to indicate that the parameter may be modified. Use < > or < > button to adjust the value.
  7. After you are done, press button to save the new value and return to the selection level (symbol disappears after selection is saved). Pressing button without pressing button will discard the value and return without saving.
  8. Press the button to leave the menu. The unit will return to normal operation if no button is pressed for more than 5 minutes.

User Parameters (Password 0009)

Parameter Description Range Default
UP 00 Enable change of operation modes ON, OFF ON (Enabled)
UP 01 Enable change of setpoints ON, OFF ON (Enabled)
UP 02 State after power failure: 0 = Switched OFF, 1 = Switched ON, 2
= state before power failure 0, 1, 2 2
UP 03 Celsius or Fahrenheit, Select ON for Fahrenheit, OFF for
Celsius ON, OFF OFF (Celsius)
UP 04 Select type of content for large digits (00= OFF): 01 =
Setpoint 02 = Humidity Sensor 03 = External Temperature Sensor 00…03 01

The control operation is defined by parameters set using the standard operation terminal. There are two levels:

  • User/display parameters (password 0009)
  • Control parameters (password 00241)

Control Parameters (Password 0241)

Note : Only experts should change these settings! See user parameter for login procedure!

Parameter Description
CP 00 Minimum setpoint limit in humidification mode
CP 01 Maximum setpoint limit in humidification mode
CP 02 Start delay for fans (Time the fan runs before control output

starts)
CP 03| Stop delay for fan (Time the fan keeps running after control
output stops)

This document covers the operation and installation instructions for the following Condair digital humidistat:

Kit No. Component No. Description
2597934 2548731 On/Off Digital Wall Humidistat

Mounting and Installation

Location:
Install the Condair CHR-NA in a protected and easy accessible place at least 1.5 m above the floor to the wall (mounting on flush-mounting or wall-mounting box). Observe the following placement notes:

  • Do not place Condair CHR-NA in niches, behind, curtains, etc.
  • Do not place the Condair CHR-NA near heat sources, within the area with direct air draft or direct sunlight.

Installation:
Refer to installation overview in section 2.

  1. Open the screw of the housing and remove the mounting plate with the connecting unit.
  2. Connect wires of the connection cable to the terminals according to the wiring diagram.
  3. At the place of location fix mounting plate (plastic screw facing downwards) with two screws to the flush-mounting or wall-mounting box (see dimension drawing).
  4. Carefully snap housing onto the mounting plate and fix it with the screw (do not tighten screw too much).
    Note : We recommend using 18-gauge wire, and maximum <100 ft distance from the unit.

Installation overview

Condair-CHR-NA-Digital-Room-Humidistat-with-Display-
FIG-1

Wall Humidistat LCD Display

Condair-CHR-NA-Digital-Room-Humidistat-with-Display-
FIG-2.

Error Messages

  • Err 1 : Sensor element in the device is not properly inserted or defective. Insert the sensor element correctly or replace it.
  • Err2, 3 & 4: Hardware or memory problem. Replace device

Sensor Calibration

Sensor inputs can be calibrated if needed

Condair-CHR-NA-Digital-Room-Humidistat-with-Display-
FIG-3

Wiring Diagrams

Wiring diagram CHR-NA for RS, EL, GS, US and SE

Wiring diagram CHR-NA for DL and ME

Wiring diagram CHR-NA with CHD-NA and APS for RS, EL, GS, US and SE

Condair-CHR-NA-Digital-Room-Humidistat-with-Display-
FIG-12

Documents / Resources

| Condair CHR-NA Digital Room Humidistat with Display [pdf] Instruction Manual
CHR-NA Digital Room Humidistat with Display, CHR-NA, Digital Room Humidistat with Display, Digital Room Humidistat, Room Humidistat, Humidistat
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

condair User Manuals

Related Manuals