TOOLOTS SRL-39E Semi-Pneumatic Laminator Instruction Manual

TOOLOTS SRL-39E Semi-Pneumatic Laminator Instruction Manual

Please read the manual carefully before use and keep it for future reference.
This instruction manual describes the operation steps and precautions of this unit in detail.
The laminator has the functions of hot lamination and cold lamination.
Thank you for purchasing and using our laminator

Safety Attention

Machine Parts Instruction Diagram

Control Panel Instruction

Temperature Control Panel

Install Lamination Rilm Diagrammatic Drawing

Method of Operation

1. Check the appearance of the machine, confirm the working voltage and turn on the power.

2. Connect the air compressor tube (diameter of the tube is 10mm, set the air pressure to the maximum. (Generally the maximum pressure of air compressor is 0.7Mpa)

3. Set the temperature, the common film temperature is set between 100-110 degrees, press the heating button on the panel, the heating indicator is bright,
indicating that the machine is in the heating state After the actual temperature ofthe roller reaches the set temperature, the heating indicator is flashing and the preheating is completed

Attention: Since there is a certain difference in the temperature of each machine, the temperature is appropriately adjusted according to the actual laminating effect.

4. Install Lamination Film

1. The film can be install after the preheating is completed. Please turn off the overlap function before install the film, run the machine, and guide the film into the roller while feeding the paper, until come out from all rollers
   Film Install method reference Page 3 ( Install films diagrammatic drawing)

2. Adjust the left and right position of the paper feed bar or film, align the edge of the film and the paper, and after alignment, tighten the positioning bar adjustment rod or the fixing screw of the film sleeve. Prevent displacement during lamination
   Attention : The width between the left and right paper feed positioning bars must be larger than the paper width. If the width between the two is too small, it will cause paper jams or poor paper feeding. So as not to cause normal lamination.

5. Operation method of Overlap function

1. The machine must be stopped.

2. Enter the exact paper length: click on the paper length number to select the area, Enter the set interface, enter the exact paper length and size, and click enter to complete.

3. Set the size that needs to be overlap: Click the paper size number selection area to enter the setting interface, enter the size that needs to be overlap, and click Enter to complete.
   Reminder
   The input value is positive, the head and tail of the two sheets of paper will overlap, it is the overlap size, otherwise the value is negative, there will be a gap between the head and tail of the two sheets of paper, and the gap size is the entered value.

4. When using the overlap function for the first time , need to turn off the overlap function, so that the overlap cylinder is lifted, the paper is placed on the feeder conveyor belt, paper head is pressed against the paper feed roller

5. Turn the “FWD/STP/REV” switch to the FWD, and the speed control knob is at the low speed state

6. Press the button of “Overlap” ON,

Press the “Run” button, the motor runs, and the lamination begins

Attention :
At this time, the “Overlap ON/OFF indicator light” Green “ON”on the display it means the overlap function are in normal working state.
On the contrary, the “Overlap ON/OFF indicator” is in pink “OFF”, indicating that the overlap function is not working properly.

Reminder
In normal continuous lamination, the paper inserted in the next sheet only needs to be stacked on top of the previous sheet. It should be noted that it cannot be completely overlap, and the distance between the heads of the two sheets needs to be misaligned 10cm.

Attention :
The paper feeding platform of this machine has a paper measuring sensor, so it can not be interrupted when loading paper, and it will automatically stop when the sensor cannot detect the paper

6. Operation method of automatic breaking function

1. When using the automatic breaking function, the dotted knife must be placed correctly , otherwise it will not be automatically breaking. Place the dotted knife at a position 5 mm away from the edge of the films, and tighten the dotted knife positioning knob
2. Turn on “Breaking” function
3. Open the automatic breaking switch on the back of the machine
4. Click the “Break” button on the display. Green “On” means in normal working state
5. Adjust the left and right positions of the “Breaking Guide Wheel”, with the dotted knife as the reference. The breaking guide wheel needs to be biased to the side of the dotted knife and to paper edge 10cm . (As shown below)
6. Adjust the tilting direction of “Breaking Guide Wheel”, with the dotted knife as the reference, the breaking guide wheel needs to be slightly inclined to the side of dotted knife. (As shown below)

Attention :
There is a breaking paper sensor between the traction rubber roller and the breaking rubber roller. When the breaking function is activated, the first paper cannot cover the paper measuring sensor, otherwise it will cause inaccurate counting and cause a breaking error. If the sensor has been covered, then the current two the seams of the paper are broken with the “manual force breaking button” when the traction rubber roller is passed, and can work normally after breaking.

7. Anti-curl adjustment method: the thinner the paper, the lower the adjustment needs to be pressed, and the thicker the paper The pole is adjusted appropriately, and the effect can be adjusted again.

Specifications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>