WITHINGS WPM05 BPM Connect Wireless Blood Pressure Monitor User Guide

October 30, 2023
Withings

WITHINGS WPM05 BPM Connect Wireless Blood Pressure Monitor

Product Information

The Withings BPM Connect is a digital monitor used to measure blood pressure and heart rate. It is intended to be used by adults with an arm circumference of 9 inches to 17 inches (22 cm to 42 cm). The device comes with a USB cable and a regulatory information leaflet.

The LED colors on the device may vary depending on the classification guidelines of your country. Please refer to support.withings.com for more information on blood pressure measurement classification.

Product Usage Instructions

  1. Sit down in a comfortable position, legs uncrossed, feet flat on the floor, arm and back supported. Uncover your left arm. Rest for 5 minutes before the first measurement.
  2. Unroll the cuff and place your left arm inside it. The button should be closer to your elbow, and the Withings logo should be closer to your shoulder.
  3. Tighten the cuff around your arm. The tube should be placed slightly toward the inside of your arm, facing the rib cage, about one inch (2.5 cm) above the bend of your elbow. Make sure the cuff is at heart level.
  4. Close the cuff at an angle if needed to ensure there are no gaps on the top and bottom. The entire cuff must be in contact with your skin. Make sure the cuff is not touching the left side of your chest. Your arm should be resting comfortably on the table.
  5. Place your left arm on a table with the cuff at heart level and your palm facing up.
  6. Press the button to turn on the blood pressure monitor. You can select a single or triple measurement with a long press on the button. Press the button again to start the measurement.
  7. Do not speak or move during the measurement.
  8. If an error message appears on the screen, please refer to the troubleshooting explanations described on page 7, or see the Help Center section available in the Health Mate app.

Note: Do not take measurement after bathing, drinking alcohol, smoking, exercising or eating. Use on adults only. Do not use on children or pets.

Box Content

  • Withings BPM Connect

  • USB Cable

  • Regulatory information leaflet

How to take a measurement

  1. Sit down in a comfortable position, legs uncrossed, feet flat on the floor, arm and back supported. Uncover your left arm. Rest for 5 minutes before the first measurement.

  2. Unroll the cuff. Place your left arm inside it. The button should be closer to your elbow, and the Withings logo should be closer to your shoulder.

  3. Tighten the cuff around your arm. The tube should be placed slightly toward the inside of your arm, facing the rib cage, about one inch (2.5 cm) above the bend of your elbow. Make sure the cuff is at heart level.

  4. Close the cuff at an angle if needed to ensure there are no gaps on the top and bottom. The entire cuff must be in contact with your skin.

  5. Place your left arm on a table with the cuff at heart level and your palm facing up. Make sure the cuff is not touching the left side of your chest. Your arm should be resting comfortably on the table.
    Do not speak or move during the measurement.
    WITHINGS-WPM05-BPM-Connect-Wireless-Blood-Pressure-
Monitor-8

  6. Press the button to turn on the blood pressure monitor. You can select a single or triple measurement with a long press on the button. Press the button again to start the measurement.

  7. If an error message appears on screen, please refer to the troubleshooting explanations described on page 7, or see the Help Center section available in the Health Mate app.

LED colors

US/CANADA
Note : Blood pressure classifications can very by geo. If you are in the EU or outside of US/CANADA see the section “LED colors: EU and Other countries”
The LED on BPM Connect may appear:

  • Blue: If BPM Connect hasn’t yet been paired with a mobile device. The LED may also appear blue during firmware updates.
  • Green : If you have normal or elevated blood pressure measurements. The LED may also appear green if BPM Connect has been paired with a mobile device.
  • Orange: If you have measurements indicating high blood pressure stage 1. The LED may also appear orange if the battery is low. You can still take a measurement.
  • Red: If you have measurements indicating high blood pressure stage 2 or hypertensive crisis. The LED may also appear red if BPM Connect battery is drained, or if there is an error during the blood pressure measurement.
  • Pink: If you press and hold the monitor button for 6 seconds until “Info” displays on the screen, and the Settings menu opens.

EU and Other Countries
The LED on BPM Connect may appear:
Blue: If BPM Connect hasn’t yet been paired with a mobile device. The LED may also appear blue during firmware updates.

  • Green: If you have normal and optimal blood pressure measurements. The LED may also appear green if BPM Connect has been paired with a mobile device.
  • Orange: If you have high normal blood pressure measurements. The LED may also appear orange if the battery is low. You can still take a measurement.
  • Red: If hypertension (grade 1, 2, 3) or isolated systolic hypertension are detected. The LED may also appear red if BPM Connect’s battery is drained, or if there is an error during the blood pressure measurement.
  • Pink: if you press and hold the monitor button for 6 seconds until “info” displays on the screen, and the Settings menu opens.
  • Note: The LED color displayed on the device may vary depending on the classi-fication guidelines of your country. Please go to support.withings.com for more information on blood pressure measurement classification.

Important information

Requirements
In order to use your BPM Connect, you need an iOS (14.0 or higher) or Android (8.0 and higher) device to install it. Thereafter, the product can be used without your mobile device on you, thanks to the Wi-Fi connection. For Bluetooth® connection, you will need your phone to synchronize your results to see them in the application.

Important safety information
Consult your doctor if you suffer from arrhythmia or arteriosclerosis. Please read this section carefully before using the BPM Connect Wi-Fi Smart Blood Pressure Monitor.

Intended use
The BPM Connect is a digital monitor intended for use in measuring blood pressure and heart rate. The device is intended to be used in a human adult population with an arm circumference of 9 inches to 17 inches (22 cm to 42 cm).
BPM Connect is a medical device.
Contact your physician if hypertensive values are indicated.
The user is an intended operator.

General safety and precautions
Do not forcibly bend the arm cuff. | Do not inflate the arm cuff when it is not wrapped around your arm. | Do not apply strong shocks and vibrations to the blood pressure monitor or drop it. | Do not take measurement after bathing, drinking alcohol, smoking, exercising or eating. | Do not immerse the arm cuff in water. | Use on adults only. | Do not use on children or pets.

General usage
Always consult your doctor. Self-diagnosis of measurement results and self- treatment are dangerous. People with severe blood flow problems or blood disorders should consult a doctor before using the blood pressure monitor. Cuff inflation can cause internal bleeding. Operational factors such as common arrhythmias, ventricular premature beats, arterial sclerosis, poor perfusion, diabetes, age or renal disease can affect the performance of the automated sphygmomanometer and/or its blood pressure reading. This is a precision measuring device that may be understood by lay users, but should still be handled with care. Exposing the device to prolonged lint, dust or sunlight might reduce its life or damage it. A damaged cuff or sensor may lead to incorrect meas-urements. The USB port should only be used for recharging the device. Parts in contact with the skin: cuff. Measurements can be affected by extreme temperatures, humidity & altitude.

Caution

  • Do not leave the blood pressure monitor unattended with infants or people who cannot express their consent.

  • Do not use the blood pressure monitor for any purpose other   than measuring blood pressure.

  • Do not disassemble the blood pressure monitor.

  • Do not operate the blood pressure monitor in a moving vehicle  (car, airplane).

  • Do not use the device with the USB cable plugged in. Improper continuous pressure of cuff or too-frequent measurements may interfere with blood flow and result in injury to  the user. Check to ensure that the use of the device does not result in prolonged impairment of your blood circulation. Do not apply the cuff over the user’s arm if it has a wound
    or medical treatment, as this can cause further injury.

  • Consult your physician before using this monitor if you have had a mastectomy.

  • Use of the device can temporarily cause the loss of function of equipment that is used simultaneously on the same limb.

After use

Cleaning

  • Do not use an alcohol-based or solvent agent to clean the device.
  • Clean the device with a soft and dry cloth.
  • The dirt on the cuff can be cleaned with a damp cloth and soap.
  • Do not rinse the device or cuff with water.
  • Do not dismantle the device, disconnect the cuff, or try to repair it by yourself. If a problem occurs, please check with the distributor.
  • Do not operate the device in a severe environment of extreme  temperature, humidity, or direct sunshine.
  • Do not shake the unit violently.
  • Do not submerge the device or any of the components in water. Do not use the device after a strong shock, such as dropping the unit on the floor.

Maintenance
If you cannot fix the problem using the troubleshooting instructions, request service from your dealer. The manufacturer will make available on request circuit diagrams, component part lists, descriptions, calibration instructions, or other information that will assist the manufacturer’s staff or authorized representative with repair. Do not use the device while doing maintenance steps.

Storage

  • Store the device and the components in a clean and safe location.
  • If storage conditions are different from the usage conditions indicated in this document, please wait 30 minutes before taking a measurement.

Error message and Troubleshooting

Error : Causes and solutions

  • Err. 201 The cuff was not properly tightened. Please try to take a new measurement and make sure you follow the guidelines.
  • Err. 202 Talk or movement has been detected during the measurement. Please try to take a new measurement and make sure you follow the guidelines.
  • Err. 203 No heart rate has been detected. Please try to take a new measurement and make sure you follow the guidelines.
  • Err. 204 Error calculating blood pressure. Please try to take a new measurement and make sure you follow the guidelines.
  • Err. 301 BPM Connect is not inflating correctly. Please try to take a new measurement and make sure you follow the guidelines. Err. 302 Contact the customer support.
  • Err. 303 BPM Connect failed to start a measurement. Please try to take a new measurement and make sure you follow the guidelines.
  • Err. 205 Heart rate measurements are outside of the 40-180 bpm range the BPM Connect is certified to measure. As such, a low heart rate can result in this error message.
  • Err. 206 The measurement has been stopped manually.
  • Err. 220 Battery level is too low. Please charge BPM Connect using the  provided charging cable before taking a new measurement.

Disposal

Actuation of European directive 2012/19/EU, for reduction in use of dangerous substances in the electric and electronic device and for garbage disposal.
The symbol applied on the device or its packaging means that at the end of its useful life, the product not be disposed of with dome tic waste.
At the end of the device’s useful life, the user must deliver it to a collection center for electric and electronic garbage, or return it to the retailer when purchasing a new device. Disposing of the product separately prevents possible negative environmental and health consequences deriving from inadequate disposal.
It also allows the recovery of materials it is composed of to save energy and resources and avoid negative effects to the environment and health.
In case of abusive disposal of devices by the user, will be applied administrative endorsements in compliance with current standards. The device and its parts must be disposed of as appropriate, in accordance with national or regional regulations.

FCC Statement

Federal Communications Commission (FCC) Statement 15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference and
  2. This device must accept any interference received, including interference that may cause undesired operation of the device.

FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

  1. This device may not cause interference, and
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

FCC ID: XNAWPM05

RF Statement

Medical Electrical Equipment needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the following. | Interference may occur in the vicinity of equipment marked with the following symbol:  | Portable and mobile RF communication equipment (e.g. cell phones) can affect Medical Electrical Equipment. | The use of accessories and cables other than those specified may result in increased emissions or decreased immunity | The device uses RF energy only for its internal function. Therefore, itsRF emissions are very low and are not likely to cause any interference in nearby electronic equipment | The device is suitable for use in all establishments, including domestic establishments and those directly connected to the public low voltage power supply network that supplies buildings used for domestic purposes |Portable and mobile RF communications equipment should be used no closer to any part of the device, including cables, than the recommended separation dis-tance calculated from the equation applicable to the frequency of the transmitter | The device is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. Any other accessories, transducers and cables may result in increased emissions or decreased immunity and EMC performance. |
The device should not be used adjacent to or stacked with other equipment and that if adjacent or stacked use is necessary, which should be observed to verify normal operation in the configuration in which it will be used. Medical Electrical Equipment needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the following. Portable and mobile RF communication equipment (e.g. cell phones) can affect Medical Electrical Equipment. The use of accessories and cables other than those specified may result in increased emissions or decreased immunity of the unit.

Guidance and manufacturer’s declaration-electromagnetic emissions
This Wi-Fi Smart Blood Pressure Monitor is intended for use in the electromagnetic environment specified below. The customer or the user of the Wi-Fi Smart Blood Pressure Monitor should ensure that it is used in such an environment.

WITHINGS-WPM05-BPM-Connect-Wireless-Blood-Pressure-
Monitor-11

Declaration – electromagnetic emissions and immunity

for equipment and systems that are not life-supporting and are specified for use only in a shielded location

The Wi-Fi Smart Blood Pressure Monitor declaration electromagnetic immunity
This Wi-Fi Smart Blood Pressure Monitor is intended for use in the electromagnetic environment specified below. The customer or the user of the Wi-Fi Smart Blood Pressure Monitor should ensure that it is used in such an environment.

WITHINGS-WPM05-BPM-Connect-Wireless-Blood-Pressure-
Monitor-12

Declaration – electromagnetic immunity
This Wi-Fi Smart Blood Pressure Monitor is intended for use in the electromagnetic environment specified below. The customer or the user of the Wi-Fi Smart Blood Pressure Monitor should ensure that it is used in such an environment.

WITHINGS-WPM05-BPM-Connect-Wireless-Blood-Pressure-
Monitor-13

Electromagnetic environment – guidance

  • Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%.
  • The main power quality should be similar to that of a typical commercial or hospital environment.
  • The main power quality should be similar to that of a typical commercial or hospital environment
  • The main power quality should be that of a typical commercial or hospital environment. If the user of the equipment or system requires continued operation during power main interruptions, it is recommended that the equipment or system be powered from an uninterruptible power supply or a battery.
  • Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.

Specifications & technical data

  • Product description: Digital automatic blood pressure monitor

  • Model: WPM05

  • Blood pressure measurement method: Cuff oscillometric method

  • Cuff inflation: Automatic inflation with air pump at 6 mmHg/s

  • Pressure sensor: Gauge sensor

  • Measurement range (pressure): 0 to 285 mmHg, DIA 40 to 130 mmHg, SYS 60 to 230 mmHg

  • Measurement range (pulse): 40 to 180 beats/min

  • Pressure sensor accuracy: Within +- 3 mmHg or 2% of reading
    Clinical accuracy (blood pressure): BPM Connect performance in measure blood pressure measurement was validated in a clinical trial. The results are within the margin of acceptance defined by the internationally recognized evaluation standard of blood pressure monitors ANSI/AAMI/ISO 81060-2:2013, EN ISO 81060-2:2014, developed by the European Society of Hypertension, British Hypertension Society and Association for the Advancement of Medical Instrumentation/American Heart Association. For more information, go to: withings.com/support

  • Accuracy (pulse): Within +-5% of reading

  • Sensor: Semiconductor pressure sensor

  • Operating conditions: 5 to 40°C, up to 90% RH, atmospheric 86Kpa~106kpa, altitude: 2000m

  • Storage and transport conditions: -20 to 70°C, up to 95% RH, atmospheric

  • 86Kpa~106kpa, altitude: 2000m

  • Arm type: Use on left arm

  • Power source: 5V 1A

  • Weight: Approx. 245g

  • Accessories: Charging cable, Quick Start Guide, Product Guide

  • Product life: 3 years

  • Wireless transmission Wi-Fi and BLE

Note: Specifications are subject to change without prior notice or any obligation on the parts of the manufacturer

Information for users in Canada

This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications made to this equipment not expressly approved by Withings may void the FCC authorization to operate this equipment.

Radiofrequency radiation exposure information:
The radiated output power of the device is far below the FCC radio frequency exposure limits. Nevertheless, the device shall be used in such a manner that the potential for human contact during normal operation is minimized.

Warranty

Withings Two (2) Years Limited Warranty – Withings BPM Connect | Wi-Fi Smart Blood Pressure Monitor Withings, 2 rue Maurice Hartmann, 92130 Issy-les- Moulineaux, (“Withings”) warrants the Withings-branded hardware product (“Withings Product”) against defects in materials and workmanship when used normally in accordance with Withings’ published guidelines for a period of TWO (2) YEARS from the date of original retail purchase by the end-user purchaser (“Warranty Period”). Withings’ published guidelines include but are not limited to information contained in technical specifications, safety instructions or Quick Start Guide. Withings does not warrant that the operation of the Withings Product will be uninterrupted or error-free. Withings is not responsible for damage arising from failure to follow instructions relating to the Withings Product’s use.

Need help?
withings.com/support

Manufacturer
WITHINGS,
2 rue Maurice Hartmann,
92130 Issy-les-Moulineaux,
FRANCE
+33141460460
Distributed by Withings Inc.,
179 South Street, Floor 5
Boston, MA 02111 USA
Ingress of water or
particulate matter
Dry storage environment
Storage temperature I 60°C
(140°F)/-20°C (-4°F)
Complies with waste
electrical and electronic
equipment directive
Type BF Applied Part (cuff)
Read this manual before use

  • Frequency band : 2402 –
  • output power : 4.45 dBm

Withings hereby declares that the device Withings BPM Connect is in conformity with the essential requirements and other relevant requirements of Directive 2014/53/EU. The declaration of conformity can be found at: withings.com/compliance
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the faailure does not amount to a major failure.
Australian sponsor: Emergo Australia Level 20, Tower II, Darling Park, 201 Sussex Street, Sydney, NSW 2000, Australia
Emergo Consulting (UK) Ltd c/o Cr360 – UL International
Compass House, Vision Park Histon Cambridge CB24 9BZ United Kingdom

Withings BPM Connect | Wi-Fi Smart Blood Pressure Monitor | V3.0 – Jan. 2022
© 2022 Withings. All rights reserved.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals