ideal lux 307244 FLY SLIM LED Ceiling Light Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
FLY SLIM
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
CEILING INSTALLATION
Open the article by unlocking the base in the rotationdirections indicated. Pay attention to positioning the base centered to your light-point.
The article is equipped with a double driver for uplight and downlight.
OPZIONALE/OPTIONAL
Warning! If you want to modify the lighting system, remove the dowlignt
driver.
Follow steps 3 and 4. otherwise jump to step 5.
Connect the chosen driver and follow the diagrams above carefully. Warning! Rely on qualified electrician to make the connection.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
Fix the article to the ceiling. In the case of a concrete base, proceed by drilling the ceiling and fixing the base using suitable hardware. In the case of a wooden base, proceed directly fixing the base to the ceiling. Pass your light-point-cable inside the base. Warning! Refer to qualified electrician to made the operation.
PUSH diagram (only for 1-10V/Push or DALI/Push drivers with dedicated Push input)
PUSH diagram (only for DALI/Push drivers without dedicated Push input
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
Connect the wires to the five-pole terminal box if installing the UpLight module.
Place the magnetic ring on the light source.
Hook the light source to the metal bracket with the carabiner.
Connect the plug coming out of the ring to the base mounted on the ceiling. Connect the Ground to the bracket on the light source.
Connect the plug of the light source to the base downlight driver.
Hook the light source to the mounted base by rotating it. Warning!
Make sure the side brackets match and hear a loud Click! (x3 times).
The light source will be effectively blocked.
*OPTIONAL
270258 FLY UPLIGHT D35 D45 3000K – 12W LED
270395 FLY UPLIGHT D35 D45 4000K – 12W LED
270401 FLY UPLIGHT D60 3000K – 18W LED
270265 FLY UPLIGHT D60 4000K – 18W LED
271002 FLY UPLIGHT D90 3000K – 25W LED
270715 FLY UPLIGHT D90 4000K – 25W LED
This product is provided with a light source with efficiency energy class of:
EAN| Light Source Model| Energy Efficiency Class| Light
Source (mA)| Light Source (V)
---|---|---|---|---
8.0217E+12| FLY D35 3000K| F| 500 mA| 34 V DC
8.0217E+12| FLY D35 4000K| F| 500 mA| 34 V DC
8.0217E+12| FLY D45 3000K| F| 700 mA| 34 V DC
8.0217E+12| FLY D45 4000K| F| 700 mA| 34 V DC
8.0217E+12| FLY D60 3000K| F| 1400 mA| 34 V DC
8.0217E+12| FLY D60 4000K| F| 1400 mA| 34 V DC
8.0217E+12| FLY D90 3000K| F| 1400 mA| 46 V DC
8.0217E+12| FLY D90 4000K| F| 1400 mA| 46 V DC
LEGENDA ICONE
| Replaceable light source by an end-user.
---|---
| Replaceable LED light source by an end-user.
| Replaceable light source by authorized personnel only.
| Non-replaceable light source.
Upon end of life of the light source, the whole product will be replaced.
| Replaceable control gear by an end-user.
| Replaceable light source by authorized personnel only.
| Upon end of life of the control gear, the whole product will be replaced.
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal
- Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the Earthing is obligatory.
- Class II Electrical safety guaranteed by the main insulation and a double or reinforced Earthing not necessary.
- Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing
- Not protected
- Protected against solid objects greater than 50
- Protected against solid objects greater than 12
- Protected against solid objects greater than 2,5
- Protected against solid objects greater than
- Dust protected.
- Totally protected against dust
- Not Protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against
- Protected against splashing
- Protected against water
- Protected against strong water
- Protected against temporary
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating
- Caution, risk of electric shock.
- Do not stare at the operating light.
IDEAL LUX s.r.l.
IDEAL LUX Warehouse
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
8.00 – 12.00 / 13.30 – 17.00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>