TOOLOTS A05 Pneumatic Filling Machine User Guide
- October 30, 2023
- TOOLOTS
Table of Contents
Model A05 Pneumatic Filling Machine
User’s Guide
Brief Introduction
The A03 manual filling machine is specially designed for filling liquid and cream from 20 to350m1. The shell of the machine is durable powder-coated and all the parts insjde are made from 304 # stainless steel and TEFLON,it 15 beneficial for individual factories and those factories of small scale.,laboratory,hospital or beauty parlor in daily use chemical section.
Technical Parsmeters
Filling Range:20-350m1 Capacity of the Hopper :30L Gross Weight:30kg Overall Dimension: 40’40’97cm
**Operational Approach for model A03 manual filier
**
To setting up the filling volume : pull the handle(Fig1.23)up at first. then
loosen the locking nut(Figl. 25). circumgyrate the measure nut(Figl. 26)
CCWtoincrease the filling volume or CW to reduces. Tighten up the locking nut
while you get a right volume. Choose a right nozzle for your bottles,try to
use a thick and short nozzle if possible.
Operational Approach for model A02 pneumatic filler
Connect the machine to an air pump by using a co 8mm pipe depresses the pedal
switch to work in jog mode, and step on the pedal switch to work
automatically. Use speed controller for inlet and outlet(fig22,2.6) to adjust
the filling speed. Then adjust the filling volume as same as model A03 manual
filler.
Attention : This machine is not fit for filling the materiels
concretionray(such as face cream or beef fat etc)or any materiels with grain.
| 1. hopper | 10. sealreceptacle | 19. oullet screw cap |
|---|---|---|
| 2. screw cap | 11. gear rack | 20. ring 23.handel |
| 3. cone screw cap | 12. iatvflir plata | 21. nozzle |
| 4. piston ring | 13. sectorpor | 22. upper locking nut |
| 5. piston rod | 14. cross shaft | 23. upper measure nut |
| 6. measure cylinder | 15. machkne base | 24. diown measure nut |
| 7. fastener | 16. .sealing ring | 25. down locking nut |
| 8. cylinder base | 17. walve plug | |
| 9. sealing ring | 18. ELspring |
| Symptom | Causation | Fault Remedy |
|---|---|---|
| Measure inaccuracies | There’s sundries between the cone screw cover (fig 1 .3) | |
| and piston ring(fig1.4). | Unpick and wash | |
| The piston ring(fig1.4) excessive frayed | Replaceing the piston ring | |
| The filling speed is unstable, the materiel flow asymmetric | Work in a |
constant speed
The materiel is ropy| Draw up the handle (41.23) slowly
The locking nut(fig 1 25, 28)$s loose| Tighten them
(For A02) Unstable air pressure| Adjust the air pressure
Materiel drops from the nozzle| The U ring is proken or melt| Replacing the 0
ring 16. 17. 18)
There’s sundries on the o ring(fig1 18)| unpick and wash
Materiel contains bubbles after filling| Operate speed is too high| Low down
the work speed
The air proof ring(fig1.9) is broken| Replacing 4(41.9)
Maintenance
a.Keep the machine body clean in case of erosion to extended service life
b.Please lubricate the abscissa axis (fig1.14), segment gear (fig1.13)and the
rack (fig1.11)termly.
c. Please unpick and clean the machine before leave it unused for a long time.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>