TOOLOTS 8101 Tire Lift Roller Instruction Manual

TOOLOTS 8101 Tire Lift Roller Instruction Manual

introduction

Thank you for purchasing our tire lift roller. This machine has the best quality. Inordertooperate correctly and prolong the use time of the machine, please be sure to read the instructionsofeach operation part of this manual carefully。

Parameter description

The “Tire lift Roller Model Number” and “Product Number” are complete to makeit easiertoprovide our technical service and supply the required parts. For greater clarity and easeof use, wehave provided the data for the tire lift roller frame in the box below. If there is anyinconsistencybetween the data in this manual and the data on the sign, the data on the sign shall prevail.

This manual is an integral part of using the machine. Using a tire lift roller Before, read each part of the manual carefully, especially the two parts of operation safety and machine maintenance 。

Save this manual for future use!

description

pig 1

A） long roller
B） short roller
C） tire lift
D)   control panel
E） support point
F） air intake

Dangerous

Note: The red frame area is the edge of the lifting area of the tire retreading frame. Pleasemakesurethat there are no obstacles in the area. When working, please keep no part of your bodyfromentering this area to avoid injury. (Figure 2)
Pic 2

overview

instruction

• The design of the tire turning frame is to assist in lifting or unloading tires with a maximumweight of less than 75kg during the operation of the tire changer.

Do not operate in accordance with the requirements of the manual.

• The manufacturer is not responsible for any damage caused by unreasonable operationnot in accordance with the instructions.

safety operation

Tire lifter are for trained professionals only.

• Changes to the machine not approved by the manufacturer, the manufacturerisnotresponsible for any damage caused.
• If the user violates the safety rules and disassembles the safety deviceofthemachine to cause damage, the manufacturer will immediately stop the safetycommitment to the machine.

Shipping

• Tire lifter must be shipped in original factory packaging, and place it in the location indicated on the box
• The packaged machine must be moved by a forklift with the correspondingliftingcapacity, the insertion direction of the trolley is shown in Figure3.
  Fig3
  
  

Test

Before turning on the machine, determine if the user’s air supply matches the machine’s requirements.

• Connect the compressed air system to the machine through the fittingontheoilwater separator (F) on the side of the case. See Figure (4)
  Pic 4 Adjust
  
  

• Step on the pedals, step down, and turn the retreaded up. When returningtotheoriginal position, the retread frame is turned back down。

Service and Maintenance

Repairs and maintenance operations by professionals.

• In order to prolong the service life of the tire rollover rack, it is necessaryto carry out daily maintenance and maintenance according to the requirementsofthemanual.
• If repairs and maintenance are not carried out regularly, the operationandreliability of the machine will not be guaranteed, and it may even causedangerto the operator or people near the machine.

Specially Note: The manufacturer is not responsible for the damage caused bytheuser’s use of other  manufacturers’ parts or due to the disassemblyor damage of the safety device

• Perform the following maintenance operations every 30 days：

Control the level of oil in the lubricator. If the level is low, you need to unscrewthe oil cupF before adding it. Only use oils of the type specified as ISO HG and with a viscosity of ISOVG32，Suchas：ESSO Febis K32,MOBIL Vacouline 1405,KLUBER32. When turning the hand valve up and down 3-4 times, check whether oil droplets enter theoil cup F. If not, adjust the oil cup screw。
note： Retighten the screws on the carriage (D) after 20 days of first us

pneumatic diagram

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>