NOVY 7830 Vision 90cm Wall Mounted Hood Instruction Manual

: June 10, 2024
: NOVY

Table of Contents

NOVY 7830 Vision 90cm Wall Mounted Hood
Product Information
Product Usage Instructions
SAFETY AND ASSEMBLY REGULATIONS
- Air supply
ACCESSORIES
Electrical connection
INSTALLATION
Dimensions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NOVY 7830 Vision 90cm Wall Mounted Hood

Product Information

The Novy Vision is a kitchen appliance designed for household use, specifically for the preparation of food. It is a range hood available in different models: 7830, 7831, 7833, 7840, 7841, 7850, 7851, and 7853. It is equipped with metal parts that may have sharp edges, so it is recommended to wear gloves during installation. The installation instructions come with the product and must be followed to ensure safe and proper installation. The product must only be installed using the original Novy parts. The range hood should be mounted at a recommended height to ensure optimal performance. The appliance can only be installed by a certified professional to guarantee safety and proper functioning.

Product Usage Instructions

Before installing the Novy Vision range hood, check the condition of the product and the mounting materials upon receiving them. Do not use sharp tools to open the packaging. Install the range hood only if it is in good condition. If you notice any damage, contact Novy immediately.

When installing the range hood, make sure that the construction where it will be mounted has sufficient load-bearing capacity.
Respect the recommended mounting height for optimal performance.
Ensure that the range hood or the construction where it will be built covers the cooking surface. The range hood should be centered over the cooktop if you are making a custom construction. The cooktop should not be larger than the range hood or the construction where it will be built.

Novy is not responsible for any damage caused by incorrect installation, connection, or usage of the product. The installation and electrical connection must be done by a certified technician to guarantee safety and proper functioning. It is recommended to have at least two persons perform the installation for easier handling of the product.

Do not use the Novy Vision range hood for any other purpose than the intended household use. It is not suitable for commercial or industrial use. The product should not be used outdoors.

If you encounter any problems with the product, contact Novy immediately. The product complies with safety regulations, butincorrect installation can cause personal injury and damage to the product.

SAFETY AND ASSEMBLY REGULATIONS

Further information on Novy products, accessories and services may be found on the internet: www.novy.co.uk
These are the installation instructions for the appliance as shown on the front. The directions for use are in a separate booklet supplied with the appliance.
These installation instructions make use of a number of symbols. The meanings of the symbols are shown below.

Symbol	Meaning	Action
Indication	Explanation of an indication on the hood.
Warning	This symbol indicates an important tip or a dangerous situation

Observe this instruction in order to prevent injury and damage to property.

Warnings before installation

This appliance complies with the applicable safety instructions. However, inexpert installation may cause personal injury or damage to the appliance.
The appliance is intended exclusively for household use (preparation of food) and excludes all other domestic, commercial or industrial use. Do not use the appliance outside.
Check the condition of the appliance and the installation fittings as soon as you remove them from the packaging. Remove the appliance from the packaging with care. Do not use sharp knives to open the packaging.
Do not install the appliance if it is damaged, and in that case inform Novy.
Check on the basis of the drawing A that all the materials for installation have been supplied. The grease filters are in the appliance.
Novy is not liable for damage resulting from incorrect assembly, incorrect connection, incorrect use or incorrect operation.
The installation and electrical connection of the appliance should be left to a recognised expert.
Safety is guaranteed only with expert installation in accordance with the installation manual. The installing technician is responsible for proper operation at the installation location.
For easier installation of the appliance, it is advisable to carry it out with at least 2 people.
Read the directions for use and the installation instructions before installing and using this appliance. You will find important information here for the assembly and use of the appliance.
Metal parts may have sharp edges, and you may injure yourself on them. For that reason, wear protective gloves during installation.

Installation instructions for the appliance

Ensure that the structure on or in which the appliance is to be installed can bear its weight.
Faulty or damaged parts may only be replaced by original Novy parts.
The larger the distance between the appliance and the hob, the less easily the cooking vapours can be taken up by the appliance. For this reason, pay heed to the stated (recommended) installation height.
If a different distance is specified in the installation instructions for the gas hob, the largest distance indicated applies.
In order to ensure that the cooking vapours are taken up in an optimal way, the appliance, or the structure into which the appliance is being installed, should extend over the hob. When using your own structure, ensure that the appliance is installed centred above the hob.
For optimal operation, the hob should not be larger than the appliance or the structure into which the appliance is installed.

Exhaust or recirculation

The cooker hood can only be used as an extractor with an exhaust duct to the outside and is not suitable to be used as a recirculation cooker hood.

Install the exhaust duct
For optimum performance of the cooker hood it is important to pay attention to the following points:

The motor outlet has a diameter of 150 mm. It is recommended to connect an exhaust duct with a diameter of 150 mm to this.
You will achieve the best operation and lowest possible noise level for the appliance by connecting the extraction duct by as short a route as possible, with as few bends as possible and using the prescribed diameter.
Use smooth, non-flammable pipes with an internal diameter that is equal to the external diameter of the connection nozzle of the hood.
Use flat duct with rounded corners and with air de-flectors. Available at Novy.
Do not reduce the exhaust diameter. This will lower the capacity and raise the noise level.
Avoid right-angle bends. Use rounded bends for effective airflow.
Use of a flexible extraction hose should be kept to a minimum, and it should only be used for making small bridging sections, for example as the link between the outlet nozzle and the extraction duct. Maximally extend flexible ducts and cut them to size.
Ensure that the extraction duct is not crushed and that there are no kinks in the duct.
Use a hose clamp or aluminum tape for airtight connections.
With a horizontal extraction duct, install it at a slight incline to ensure that condensation does not run back to the appliance.
Condensation may arise as a result of temperature differences if the extraction duct passes through cool rooms. Ensure that the extraction duct is insulated.
In case of an exhaust pipe through the outside wall passing a cavity wall, make sure that the exhaust duct fully bridges the cavity and slightly declines to the outside.
In case of an exhaust pipe through the wall, use a wall vent.
In case of an exhaust pipe through the roof, use a double-walled roof passage with adequate outlet capacity.
When connecting to a short extraction duct, it may be desirable to install a non-return valve in the duct in order to prevent backdraught from wind.
Make sure that sufficient air is supplied. Fresh air can be supplied by slightly opening a window or an outside door or by installing an inlet grate.
The appliance may not be connected to a flue or chimney that is currently in use, or that serves as ventilation for rooms with hearths.

Air supply

However large the kitchen or the room with open kitchen is, only so much air can be extracted from the room as is supplied. Too little air supply could result in a yield loss of 50% and more.
If the extraction is used at the same time as a combustion system (for example heaters fired by gas, oil, wood or coal, hot water boilers using gas, gas hobs and gas ovens), combustion gases may be sucked back in and lead to poisoning.
A combustion system uses air from the room as combustion air. Combustion gases arise as a result, which are removed to the outside by an extraction system.
The appliance sucks in air from the kitchen and adjacent rooms. Negative pressure occurs if the air supply is inadequate. The toxic gases are then sucked back from the chimney or extraction duct into the room.
With simultaneous use of the appliance and combustion appliances in the same room, the negative pressure may not exceed 4 Pa (=0.04 mBar). Negative pressure can be prevented by allowing sufficient air into the room through openings that cannot be closed (for example through windows or doors, in combination with a ventilation cabinet in the wall).
Have an expert assess the overall ventilation system in your home for a proposal on suitable measures in the area of air supply.

When using the appliance with an internal or external motor (unit) with air extraction to the outside, there must be adequate air supply in the room where the appliance has been installed/is positioned, so that fresh air can flow in. Fresh air can be provided by tilting a window, opening a door or installing an inlet grille.

Installation instructions for the outlet

The appliance may only be connected with the power plug to a socket with an earth (230 V – 50 Hz).
Safety is only assured when the appliance is connected to an earth cable in accordance with the instructions laid down.
The appliance must be able to be disconnected from the power at any desired point.
Position the socket in such a way that the power plug of the appliance can be inserted easily.
Do not use an extension cable for the connection to the electrical mains.
Electric shock: never switch on a faulty appliance, this could cause an electric shock. Take the power plug out of the socket, or switch off at the distribution cabinet. Contact the Novy service department.
Repairs and replacing faulty or damaged wiring must only be carried out by technicians who have undergone instruction by Novy.
Moisture that has got into the appliance may cause an electric shock. Do not use a high-pressure or steam cleaner.

ACCESSORIES

InTouch
InTouch offers you the possibility to control the Novy cooker hood from the Novy InTouch induction cooking hob. The cooker hood can be combined with Novy In-Touch induction hobs using the optional InTouch kit. Kit for InTouch includes an interface and a remote control. The new interface must be fitted before installing the cooker hood as a replacement for the original interface. The kit must be installed by an authorised person.

Visit the website for the different models of induction cooking plates with InTouch.

Kit for InTouch 990.021

Chimney extension
If the standard chimney is too short, you can always opt for a extension chimney. When ordering an extension the lower chimney is included to avoid colour differences.

Chimney extension stainless steel
(extension by max. 280 mm) 7830.100
Chimney extension black
(extension by max. 280 mm) 7833.100

Accessories circular exhaust tube

Circular exhaust tube length 1000 mm Ø150 mm 906.415
Connection piece Ø150 mm 906.417
Curve 90° Ø150 mm 906.416
Aluminium external grill for Ø150 mm 906.178
Wall conduct kit for ducting Ø150 mm including built-in heat retention non-return valve 906.420
Non-return valve Ø150 mm 906.432

Accessories flat exhaust duct

Flexible exhaust tube length 750 mm 906.408
Flat exhaust channel duct1000 mm (dimensions: 89x222x1000 mm) 906.401
Connection piece (dimensions: 94x227x80 mm) 906.402
Horizontal curve (dimensions: 94x227x290 mm) 906.403
Vertical curve (dimensions: 94x175x227 mm) 906.404
Curve 15° (dimensions: 94x227x138 mm) 906.418
Corner adapter (dimensions: 94x227x205 mm) 906.405
Transition piece to Ø150 mm (dimensions: 94x227x190 mm) 906.406
Wall conduct kit for for flat exhaust duct 89x222mm including built-in heat retention non-return valve 906.425
Stainless Steel blind grill with non-return valve (dimensions: 290 x 160 mm) 906.407

General accessories

Hose clamp adjustment Ø60-215 mm 906.291
Aluminium tape roll 50 m 906.292
Stainless steel cleaner: maintenance product for cleaning the stainless steel 906.060

Further information on Novy products, accessories and services may be found on the internet: www.novy.co.uk

Because of the substantial own weight of the hood, the contruction must have sufficient load bearing capacity.

Electrical connection

The cooker hood is equipped with a power cord and plug with grounding. Connect the plug to a mains socket with grounding. Connection via a mains socket is recommended.
Mount the mains socket easily accessible.
It must be possible to disconnect the cooker hood from the power supply at any time (e.g. in case of service).
Below you will find two options for how to connect the cooker hood electrically.

Option 1

The cooker hood is mounted with a chimney and the air outlet is upwards.
The mains socket is placed behind the chimney.
Connect the plug of the cooker hood to the mains socket with grounding

Option 2

The cooker hood is mounted without a chimney and the air outlet is to the rear.
The mains socket is placed directly above the cooker hood (minimum distance 30mm).
Connect the plug of the cooker hood to the mains socket with grounding
The plug and socket are visible!

INSTALLATION

A. Check on the basis of the drawing A that all the materials for installation have been supplied. The grease filters are in the appliance.
Determine the mounting height ‘h’ above the hob:

NOVY-7830-Vision-90cm-Wall-Mounted-Hood-4

Determine the mounting height ‘h’ above the hob:
- Recommended mounting height with induction, electric or ceramic hob (Hmin-Hmax) (mm): 500 – 750
- Mounting height with a gas hob (Hmin-Hmax) (mm): 650-750
The height at which the 2 mounting hooks are mounted is determined by: chosen height “h” + 480 mm. Draw a level horizontal line at this height.
- Drill the holes in the wall using an 12 mm drill.
  The distance between the 2 holes is 510 mm (ensure that hood is positioned centrally above the cooker plate).
Mount the 2 suspension hooks in the wall. The suspension can be levelled by adjusting the adjustment screws (at the bottom). This can be done in advance, or after the cooker hood has been removed from the wall.
As standard, the exhaust of the motor faces upwards.
In order to do this, follow the instructions: 4 → 9 .
Installation with exhaust of the motor facing upwards (standard):
Mount the upper spacer bracket at 20mm between the ceiling and the centre point of the holes in the bracket. Make sure that the spacer bracket is mounted perpendicular to and in the centre of the vertical axis. Use the plugs and the screws.
Hang the extraction hood over the mounting brackets.
Grasp the underneath of the glass plate (A) at the left and right and pull it firmly forwards. Open the glass plate so that the grease filter is visible. You can remove the metal grease filter (B) from the hood.
There are 2 holes on the inside of the hood. Mark these holes on the wall. Depending on the wall, you can position the screws directly in the wall or remove the hood from the wall first, drill the holes, and use the plugs and screws. After this, replace the hood in the brackets and fasten the hood to wall with the 2 screws.
Place the exhaust pipe on a connection nozzle of the motor using aluminium tape or a hose clamp.
- Put the plug into the wall socket.
- Replace the grease filters in the extractor hood.
Take the two chimney parts and place them onto the wall-mounted chimney hood. Make sure that this is done carefully in order to prevent the chimney hood or the chimneys from being damaged. Screw the upper chimney tight to the spacer bracket with 2 screws.
Installation with exhaust of the motor facing to the rear (turn motor):
First open the bottom plate and remove the filters from the hood. A cable is connected to the motor with a connector. First disconnect the connector from the motor. Afterwards, unscrew the six screws from the upper side and the six screws on the rear side.
The entire motor plate including motor can now be turned so the motor exhaust is directed towards the rear.
Tighten all 12 screws. In order to be able to reconnect the cable back to the motor using the connector, you must first loosen the pull-relief from the cable. The pull-relief can be found next to the access hatch in the hood. Ensure there is enough cable length to allow the connector to be reconnected to the motor. Make sure that the pull-relief is locked.
Use the dimensional drawing to ascertain the correct position of the exhaust duct. Place the exhaust pipe on a connection nozzle of the motor using aluminium tape or a hose clamp.
Hang the extraction hood over the mounting brackets.
Grasp the underneath of the glass plate (A) at the left and right and pull it firmly forwards. Open the glass plate so that the grease filter is visible. You can remove the metal grease filter (B) from the hood.
There are 2 holes on the inside of the hood. Mark these holes on the wall. Depending on the wall, you can position the screws directly in the wall or remove the hood from the wall first, drill the holes, and use the plugs and screws. After this, replace the hood in the brackets and fasten the hood to wall with the 2 screws.
Put the plug into the wall socket.
- Replace the grease filters in the extractor hood.