GENIE GIRD1D 41486R Single Door External Receiver Instruction Manual

: June 4, 2024
: GENIE

Table of Contents

Specifications
Dimension
PRE-INSTALLATION
INSTALLATION
FCC Statements
Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GENIE GIRD1D 41486R Single Door External Receiver Instruction Manual

WARNING

MOVING DOOR CAN CAUSE SERIOUS INJURY OR DEATH.

Wall Console must be mounted in sight of door, at least 5 feet above floor and clear of moving parts.
Keep people clear of opening while door is moving.
DO NOT allow children to play with the remote or door operator.
If SAFETY REVERSE does not work properly:
Close door then disconnect operator using the manual release handle.
DO NOT use remote controls to operate door.
Refer to Door and Door Operators Owners Manuals before attempting any repairs

Specifications

Remote Capacity: 64
Voltage/Current/Hz:
Power Pack: 100-240VAC, 0.5A, 50-60Hz
Power Pack Output: 12VDC, 1A
Receiver Input Voltage: 9-42VDC, 200mA, 50-60 Hz
or: 9-30VAC, 200mA, 50-60 Hz
Temperature Range: -30 F to 1 58 F

Dimension

IMPORTANT NOTICE: This kit may only be used on an operator manufactured 1993 and later with working safety sensors.

PRE-INSTALLATION

For use on momentary contact capable units only

If existing receiver will no longer be used, erase remoter. Refer to operator owners manual, if needed.
Determine power source and wire to receiver using figures 1, 2 or 3. Refer to operator owners manual, if needed.

INSTALLATION

Unplug or turn off breaker that supplies power to operator.
Find a suitable mounting point for receiver within a few feet of the operator.
Mount receiver to wall or ceiling. Due to variations in mounting methods, hardware is not included.
Strip ends of included bell wire and install between receiver and residential (Fig.1-A) or commercial operator connections. If using the recommended power supply, plug connector from power pack into receiver (FIG. 1). To wire for an alternate power supply in a commercial application, see FIG. 2-3.
Install coax antenna on to receiver coax connector.
If using 115VAC power pack, plug power pack into standard 1 15VAC outlet.
Use included staples to tidy any hanging wires.
Restore power to operator.

WARNING
During programming, the door operator could begin to run. Stay away from moving door and its parts. To prevent door from moving, close door using the wall button and disconnect it from operator by pulling Emergency Release Cord (See owners manual).

NOTE: Programming must be completed with 30 seconds upon pressing programming (LEARN) button or receiver will turn off remote pairing mode. Press LEARN button again to enable pairing mode and resume programming remote.
NOTE: If receiver does not perform properly, check connections between power source and receiver and connections between receiver and operator.

PROGRAMMING INTELLI CODE” REMOTE:

Remove tab to activate remote control

Press the LEARN button on the receiver. (LED begins flashing).
Press the remote button once. (LED will change to solid).
Press the remote button a second time (LED will turn off).
The next remote button press will activate the receiver.

NOTE: If receiver LED flashes rapidly for 5 seconds then receiver memory iS full. Erase remotes to enable programming.

Clearing All Remotes:

Press and hold the LEARN button. (LED changes to solid).
After approximately 20 seconds the red LED will flash three times. Release the
LEARN button. All remotes have been cleared from the receiver.

REPLACE REMOTE BATTERY WITH CR2032 COIN CELL BATTERY.

Open the remote case using a washer or coin that fits into the slot at the top of the remote.
Replace battery. Match battery polarity symbols inside battery housing.
Align components and snap case closed.

FCC Statements

FCC Part 15.21 Statement:
Changes or modifications not express y approved by the party responsible for compliance could void the user’s authority to create the equipment.

This device complies with FCC part and Industry Canada Licence-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation of the device.