MFL 307004 Thames Up Down GU10 Wall Sconce Instruction Manual

: June 4, 2024
: MFL

Table of Contents

Warranty
Installation Requirements
Installation Directions
Safety Tips
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MFL 307004 Thames Up Down GU10 Wall Sconce

Thank you for purchasing this quality MFL product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this luminaire. Please keep instructions for future reference.

Warranty

This luminaire is covered by a 12 month warranty. The warranty is from date of purchase, not the date of installation.
If the luminaire is not assembled and installed by a licensed electrician, the warranty will be void.
Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty.

Installation Requirements

Must be assembled and installed by a licensed electrician.
All wiring and installation of the luminaire must adhere to the latest local and national wiring rules.
eg. AS/NZS 3000 Electrical installations.
This luminaire is a Class I product and must be earthed during wiring and installation.
Do not exceed the maximum wattage rating.
Select a suitable location for installation:
– This luminaire is suitable for indoor use only.
– The mounting point must support 2 times the weight of the luminaire.
– Ensure the luminaire is not installed in direct line of an air vent/system.
– If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
Take care not to pull any electrical wires during unpacking as this may damage the connection.
Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.

Installation Directions

Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.

Remove the mounting bracket (B) from the luminaire body (H) by loosening the two screws (E).
Use the mounting bracket (B) as a template to mark the screw positions on the wall.
Install the mounting bracket (B) onto the wall by using appropriately sized mounting screws and anchors. Ensure the screws (C) and anchors (A) used are suitable for the mounting surface and the surrounding environment.
Remove the cover of the terminal box by a screw driver.
NOTE: Keep the cover of the terminal box. DO NOT discard the cover.
Connect the mains supply wire to the terminal block. Ensure the wires are secure and no bare wires are exposed.
Mains Supply Wire
Earth – Yellow/Green
Neutral – Blue
Live – Brown Brown or L
Luminaire Wire / Terminal Block
Yellow/Green or
Blue or N
Brown or L
Reinstall the cover of the terminal box back onto the terminal block.
NOTE: Check and ensure the cover is secured.
Install the luminaire body back onto the bracket by tightening the screws (E).
Install the globes (not included) into the lamp holders then install the holding rim (G) to secure the globes in place.
After the installation, switch on the luminaire to test and enjoy your new lighting product.

Safety Tips

Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the luminaire.
To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
Select a suitable location away from liquids and hazards.
Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
To clean, wipe with a damp clean cloth. Do NOT soak or immerse the luminaire in water or other liquids.