MFL 177098 Click Wifi Camera Instruction Manual
- June 6, 2024
- MFL
Table of Contents
Installation Instructions
CLICK WIFI CAMERA
SKU# 177098
Rated Voltage 5V
Thank you for purchasing this quality MFL product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation, and use of this product. Please keep the instructions for future reference.
Warranty
-
This product is covered by a 2-year warranty. The warranty is from the date of purchase, not the date of installation.
Please retain the proof of purchase. -
Warranty will be void if there is any damage due to improper usage or modification of the product.
-
Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.
Installation Directions
-
Before installation, check the installation location in which the ceiling has access to a socket outlet. If it does not, please contact a licensed electrician to arrange the installation of the socket outlet.
-
Select a suitable location for installation:
− This product is suitable for indoor use only.
− Ensure this product is not installed in the direct line of an air vent/system.
− If installing the product in an area prone to moisture, ensure that the area is well ventilated and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty. -
Take care not to pull any electrical wires during unpacking as this may damage the connection.
-
Lay out all the components on a smooth surface and make sure there are no components missing before assembling.
-
If parts are missing, return the complete product to the place of purchase for inspection or replacement.
-
Check whether the product has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair, or replacement.
-
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.
NOTE: Before installation, plug the product into a socket outlet to ensure the camera is working correctly.
TRIM INSTALLATION
- Cut an installation hole of Ø 92mm into the ceiling. Fig.1
- Ensure the socket outlet can be readily accessible for easier installation. Fig.2
- Press the springs (A) up and in towards the frame (B) and install the frame (B) into the cut-out hole. Fig.3
- Connect the camera to the power adaptor via a USB connector. Fig.4
- Insert the power adaptor plug into the socket outlet and ensure it is fully plugged in. Fig.4
- Insert the camera assembly (G) into the frame (B) and secure it by rotating the tabs (E) into the grooves (F) until it locks into position. Fig.5
- After the installation, switch on the camera and refer to the Lucci Connect user guide for how to use this product.
SKU# 177092 – Trimless Frame Kit is required for installation, this is sold separately and contains Parts C & D.
- Remove the trim (B) from the frame body (A). Install the trimless frame (D – not included, sold separately) and the ring (C – not included, sold separately) onto the frame body (A). Fig.1
- Cut an installation hole of Ø 92mm into the ceiling. Fig.2
- Ensure the socket outlet can be readily accessible for easier installation. Insert the trimless frame (D) into the ceiling and align with the installation hole. Fig.3
- Secure the trimless frame (D) by installing two screws through the ceiling and allowing the head to countersink into the plasterboard. Fig. 4 The screw heads should be countersunk into the plasterboard by 1-2mm. Fig.5
- Adjust the ring (C) so it is 1-2mm above the plasterboard level.
- Plaster the ceiling to cover the screw heads and the ring (C). Wait for it to dry Fig. 6. Sand back the plaster until the surface is smooth Fig. 7. Repaint the ceiling Fig. 8
- Connect the camera to the power adaptor via a USB connector. Fig.9
- Insert the power adaptor plug into the socket outlet and ensure it is fully plugged in. Fig.9
- Insert the camera assembly (G) into the frame (B) and secure it by rotating the tabs (E) into the grooves (F) until it locks into position. Fig.11
- After the installation, switch on the camera and refer to the Lucci Connect user guide for how to use this product.
Safety Tips
- Always ensure the power is OFF before performing any maintenance, cleaning, or making any adjustment to the camera.
- To avoid injury or damage to the camera, ensure that power leads and screws are secure before connecting the power.
- Select a suitable location away from liquids and hazards.
- To clean, wipe with a soft damp clean cloth. Do NOT soak or immerse the product in water or other liquids.
- Ensure that the product does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
Specifications
SKU #
Rated Voltage
Rated Wattage
| 177098
---|---
INPUT: 5V, 1A
Max. 4.5W
Weight
Cut-out Size
Dimensions| 0.55kg
0 92mm
H:100mm Dia:100mm
Power adaptor
Pixel IR Distance| INPUT: 100-240V—,
OUTPUT: 5V , 1A
Pixel
IR Distance
| 1 Megapixel
10m
WDR
Bit RateMax Picture
SizeAudio
Storage| Digital Wide dynamic range
32Kbps-2Mbps
1280×720
Pixel
IR Distance Two-way audio
Support Micro SD, Max. 128GB (not included)
Frequency
Wifi SecurityAdjust Angle| 2.4GHz-2.4835GHz
WPA-PSK / WPA2- PS encryption
TiltNertical: -10° to 75°
Pan/Horizontal: 0° to 355°
Camera Size| 63mm x 58mm x 96mm