ENGO CONTROLS EASYBATB Wired Thermostat User Guide
- August 9, 2024
- ENGO CONTROLS
Table of Contents
- EASYBATB Wired Thermostat
- Product Compliance
- Technical Informations
- Connection description for EASY230W / EASY230B
- Connection description for EASYBATW / EASYBATB
- Description of the LCD display + description of the buttons
- Proper thermostat location
- Lock / Unlock the thermostat’s keys
- Installer parameters
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Wired Thermostat, 230V
Quick Guide
EASYBATB Wired Thermostat
Ver. 3
Release date: I 2024
Soft: v0.6
Producer:
Engo Controls S.C.
43-262 Kobielice
4 Rolna St.
Poland
Distributor:
QL CONTROLS Sp z o.o. Sp. k.
43-262 Kobielice
4 Rolna St.
Poland
Wired, non-programmable thermostat, battery powered (2xAAA) or 230V AC powered. It is used for wired control of heating or cooling devices and systems. It works by maintaining comfortable conditions in the room, in line with the setpoint temperature set by the user. It is connected directly to a heat source or wiring centre. For a better fit, the model is available in two colors. Safe, reliable, easy to use.
Product Compliance
This product complies with the following EU Directives: 2014/53/EU, 2011/65/EU
Technical Informations
| Power supply | 230V or 2xAAA batteries |
|---|---|
| Max current | 3 (1) A |
| Temperature range | 5 – 35°C |
| Display temperature accuracy | 0,1°C |
| Control algorithm | TPI or Hysteresis (±0.2°C to ±2°C) |
| Communication | Wired |
| Output control | COM / NO (voltage-free) |
| IP protection class | IP30 |
| Dimension [mm] | 80 x 80 x 22 mm |
Connection description for EASY230W / EASY230B
a) Connection diagram for gas boiler
b) Connection diagram to pump / actuator
c) Connection diagram to the control box
Connection description for EASYBATW / EASYBATB
a) Connection diagram for gas boiler
b) Connection diagram to pump / actuator
c) Connection diagram to the control box
Legend:
**Boiler – Boiler connection* – Boiler’s contacts for ON/OFF thermostat
(according to the boiler’s instructions)
Pump
Valve
L, N – power supply
COM, NO – voltage-free output
SL1** – 230V control input in the control box
– fuse
Description of the LCD display + description of the buttons
- Current / set room temperature
- Temperature unit
- Heating mode icon
- Cooling mode icon
Proper thermostat location
For the thermostat to work properly, it must be installed in a suitable place.
Preferably approx. 150 cm above floor level, away from sources of heat or
cold. In addition, the thermostat should not be installed behind curtains or
other obstacles or in places with high humidity, as this will prevent an
accurate measurement of the temperature in the room. It is not recommended to
install the thermostat on an outside wall, in a draft or in a place where it
will be exposed to direct sunlight.
Lock / Unlock the thermostat’s keys
To lock the keys on the thermostat, press and hold simultaneously and buttons
for 7 seconds. After the screen appears, release the keys. Thermostat is
locked.
To unlock the keys on the thermostat, press and hold simultaneously and
buttons for 7 seconds. After the screen appears, release the keys. Thermostat
is unlocked.
Installer parameters
WARNING!
After entering the service menu, use or buttons to choose parameter.
For the parameter selection to be confirmed, wait 3 seconds.
The screen will appear with the settings that you can change with or buttons.
Wait 3 seconds for the selection to be confirmed.
The thermostat will go to the home screen.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>