INOVU LT1 White Desk Mount Installation Guide
- June 1, 2024
- INOVU
Table of Contents
INOVU LT1 White Desk Mount
Product Overview
The INOVOU PREMIUM MOUNT LT1 is a desk mount for monitors ranging from 17 to 36 inches and supports a weight of 3 to 12 kilograms.
Specifications
| Feature | Specification |
|---|---|
| Monitor Size | 17″-36″ |
| Weight Capacity | 3-12kg |
| Mount Type | Desk Clamp |
| Desk Thickness | 20-100mm |
| Tilt Range | -90° to +15° |
| Swivel Range | 360° |
| Pivot | 180° |
| Material | Information not provided |
| Net / Gross Weight | Information not provided |
Product Usage Instructions
Mounting the Monitor to the Plate
- Attach the monitor to the VESA plate (12).
- Secure the monitor in place.
Installing the Monitor on the Arm
- Clip the monitor onto the arm.
- Ensure it is securely in place.
Adjustments
Make necessary adjustments to achieve the desired screen position and angle
for optimal viewing experience.
Installation Steps
Preparation Before Installing a Monitor
Ensure that your monitor has VESA 100x100mm or 75x75mm holes on the back.
Without these, the mount cannot be installed. Remove the original stand from
the monitor, being careful not to damage the screen.
Mounting the Base
-
Clamping the Base (CLAMP)
Select the appropriate position based on the desk thickness (20-100mm) and tighten the clamp using the 4x4mm Allen key (E). -
Mounting the Base – Drilling or Cable Management Hole (GROMMET)
Keep the flared side down. The minimum to maximum diameter for the hole is 8.5-70mm. Tighten as instructed using the 4x4mm Allen key (E).
Attaching the Monitor to the Plate
Attach and tighten the monitor to the VESA plate using the screws provided.
Use the 5x5mm Allen key (F) for tightening.
Installing the Monitor on the Arm
Slide the monitor with the attached plate onto the arm and clip it into
place.
Adjustments
To adjust rotation and inclination, use the 5x5mm Allen key (F) at
positions 1 and 2 respectively. Adjust the monitor height after installation
by balancing the arm’s force with the weight of the screen using the Allen key
(F).
Cable Management
Remove the cable cover, place your cables, then replace the cover to
conceal the cables once handling is complete. Fix the clip (6) to finish.
Package Contents
- 4x M4x12MM Screws (A)
- 4x M5x12MM Screws (B)
- 3x M6x12MM Screws (C)
- 8x ø6.5Xø13X1.8 Washers (D)
- 1x 4x4mm Allen Key (E)
- 1x 5x5mm Allen Key (F)
- Various other components including mounting plates, clips, and protective pads
Contact Information
For any incidents encountered with the equipment, please contact INOVOU support at support@inov-u.com.
FAQ
What is the weight capacity of the Inovu Premium Mount LT1?
The weight capacity is 3-12kg.
What is the maximum desk thickness this mount can accommodate?
The mount can accommodate desk thickness ranging from 20mm to 100mm.
Does the mount allow for monitor inclination and rotation pivot?
Yes, the mount allows for both inclination and rotation pivot for added comfort and flexibility.
What monitor sizes is the INOVOU PREMIUM MOUNT LT1 compatible with?
It is compatible with monitors ranging from 17 to 36 inches.
How often should I check the mount's fixations?
Check the fixations every two months to ensure they are not loose.
Where can I get support if I encounter issues with the INOVOU PREMIUM MOUNT
LT1?
You can contact INOVOU support at
support@inov-u.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>