SCANSTRUT SC-MAG-01 Magnetised Wireless Charger User Manual
- June 10, 2024
- SCANSTRUT
Table of Contents
SCANSTRUT SC-MAG-01 Magnetised Wireless Charger User Manual
IMPORTENT
READ THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.
Techancial information
| Input voltage range | 10-30V (12/24v system) |
|---|---|
| Input current max | 2V |
| Output power draw | 10W(9V,1.1A) |
| Standby power draw | <0.2W |
| Waterproof rating | IPX6 front and back |
| Certification | CE, UKCA,FCC,IC,ROHS,RCM,PSE |
Tools required
-
jigaaw
-
Silicone Sealant
-
Power Drill
-
Drill bit (for piolt holes)
-
ROKK Wireless magnetised Wireless Charger
-
No 6×3/4(19mm) Self tappimg CSK Philips Screw
| Material | No.6 Screw |
|---|---|
| Soft Material E.g plywood | 2.5mm(3/32) |
Hard Material
E.g Fiberglass acrylic, hardwood| 3mm (1/8)
Installation instruction
-
Chosse mounting location ensuring there is enough space behind mounting surface.
-
Use the template to mark cut lines and drill pilot holes.
-
cut holes using template and jigsaw.
-
peel backing off 3M gasket.
-
Secure with x4 No6. (3.5mn)x 3/4 (19mm) self tapping CSK Philips screws provided. add silicone sealonetto screw holes.
-
Connect to 12/24V supply .Fuse and select cable diameter according to input voltage and current.
Scanstrut.LTD 5 Dart Bussiness Park Clyst St. George, Exeter Ex3 0QH
IN EXTREME USAGE ENVIROMENTS PERFORMANCE MAY VERY
This product is designed to securely mount phones under normel usage conditions . The end user is entirelu responsible for conditions in which their device is used . See WARRANTY Section for further details.
Scan strut recommends installation is carried out by a qualified electrician , NO liability is accepeted for damage and/ or injury caused by incorrect insallation
WARNING:
This product is to be connected o a 12V DC or 24V dc battery power source only
the power supply mus be switched off before installation .
An appropriate fuse or circut breaker must be used between the battery / power source and this product . Check for correct polarity of all wiring before swiching the power on.,
This producty may contain high voltages do not temper with the produc.
This product is NOT approved for use in hazardous / flammabel atmosphere e.g engin room .
Before drilling any holes , ensure the area behind ther mounting location is clear of wires , fuel , and all other hazardous objects.
Ensure any holes cut will not significantly weaken the structure of the mouting surface.
if the product needs to be mounted outside . it must be mounted in a location safely above the waterline, where it is not of being submerged.
The product is designed specifiically for the charging of Magsafe compatible device.
The cable must be retained and no interfere with mechanical system.
This product contain no user serviceable components. Do NOT attempt to repair or alert the product in any way.
This product will charge only with Magsafe compatible cases. Phones cases may or alter over all charge performance.
When used in a very high/low ambient temperture/direct or prolonged sunlight the product may temporanily shutdown,this is a safetly feature of the electronics.
The IP rating is only valid if correctly installed as per these instructons and on a perfectly fla, non-porous, smooth surface.
When selecting a mounting loction, avoid places exposed to heat -raditaing appliances and poorly ventoleted areas.
EMC INSTALLTION GUIDELINE
Scanstrut products conform to Electromagnetic Compatibility (EMC) regulations,
to ensure that electromagnetic interference between equipment is miniised.
Correct installtion is required to ensure that electromagnetic interferencesis kept to a minmum.
WIRING
When extending the cable from battery/power source to the product, ensure
there is consistently a minmum of 10v being provided to the product. A wire
gaguge of 18 AW(0.82mm2) is recommended for any length of extension.
The electric schematic is to illustrate how the product should be connected to a 12v DC battery/power supply.
ENVIRONMENTAL PROTECTION
Waste eletrical product should not be dispose of with household waste. please
recycle where facilities exsist. Check with your local Authourity or retailer
for recycling advice.
IMPORTENT
Scanstruct LTD. accepts no responsibility for any injuries or other damages
arising fromthe use of their product in any circumtances.
WARRENTY
A 2 years , non-transferable warrenty covers this Scanstruct product only and
not any decives that are mounted in it or on it. No warrenty is given for
users’devices and users exposes their devices to hazards, known or unknown, at
their own risk.
FCC WARNING
This device complies with part 15 of the FCC Rules. operation is subject to the following two condidtion:
- This device may not cause harmful interference, and (2) this device must accept any interfernece recevid, including interference that may cause undesired operation.
Any Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. these limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. How ever, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to a radio or television reception, which can be determined by turning the equipment off and on, the users is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Rf exposure statement :
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance between 20 cm the radiator your body.
This device contain license -exempt transmitter(s) that comply with innovation, Science and Economic Development Canad;s license -example RSS(s). Operation is subject to the following two condition.
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
IC: 28360-SCMAG01
This equipment complies with IC Radiation exposures limit set forth for uncontrolledly environment This equipment should be installed and operated with minimum distance 10cm between the radiator and your body.
Scanstrud LTD, Declares the product ‘Magnetized Wireless Charger’
SKU:SC-MAG -01 is in compliance with EMC CE -RED Directive(2014/53/EU)and
standard EN62368
The CE certificate of conformity can be found at:
For latest tech info visit : www.scanstrut,com/rokk- wireless
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>