D-Link DNC-100 WLAN with Nuclias Connect User Guide

Instructions for setting up a guest WLAN with Nuclias Connect
DNC-100 or DNH-100
With Managed Switch DGS-1210 and a Fritzbox

DNC100 WLAN with Nuclias

To set up a guest Wi-Fi in addition to the main Wi-Fi, you need to enable an additional SSID in the DNC/DNH-100.
To prevent communication between the main and the guest WLAN, VLANs are used. This requires a managed switch, in this manual a DGS-1210 Rev.D.
A Fritzbox is used as an Internet gateway (router).
In this case, we make use of the guest access on LAN port 4 of the Fritzbox.

Here in the example:
– Connect the Fritzbox with its LAN port 1 , 2 or 3 to LAN port 1 of the DGS-1210.
– Connect the DNC-100-PC/DNH-100 to LAN port 8 of the DGS-1210.
– Connect the DAP access point to LAN port 15.

Setting up the Fritzbox

1. Call up the configuration of your Fritzbox and log in.
   

2. Select the Heimnetz menu on the left, then Netzwerk and then Netzwerkeinstellungen.
   At Gastzugang activate the Gastzugang für LAN 4.
   Click Apply at the bottom right.
   

3. Slide the window that appears all the way to the bottom. At the bottom left, under WAN-Einstellungen, click weitere Einstellungen.
   Slide the window that appears all the way to the bottom.
   On the right, click IPv4-Einstellungen.
   

The DHCP server must be enabled.
Below you can see the IP network, which the Fritzbox will assign to the Gastnetz. If you have made a change, click OK.

The configuration of the Fritzbox is now complete.
Now turn to the DGS-1210.
Very important:
Do not connect the LAN port 4 of the Fritzbox to the LAN port 4 of the DGS-1210 yet. This will only happen at the very end.

Setting up the DGS-1210

1. Go to the configuration of the DGS-1210. Please follow the instructions in the manual of the DGS-1210.
   In this example, the DGS-1210 already has an IP address that matches the network.
   Log in.
   The default password is admin. Please leave the language in English.
   Click OK.

2. If necessary, click Exit.
   

3. Note: Under System Settings, adjust the IP address setting of the DGS-1210 to the IP network of your network if necessary.
   The required VLAN configuration in the DGS-1210

4. Select the VLAN –> 802.1Q VLAN menu on the left.
   Asymmetric VLAN must be disabled.
   Click on the default VLAN 1.
   

5. Since the guest network LAN port 4 of the Fritzbox will be connected to LAN port 4 of the DGS-1210, set port 4 to Not Member and click Apply.
   

6. Click Add to create an additional VLAN.
   

7. At VLAN ID (VID) enter 10.
   VLAN Name is e.g. GuestWLAN
   Set port 4 to Untagged and port 15 to Tagged
   Later at Port 4 the Guestnetwork port 4 of the Fritzbox will be conencted.
   At Port 15 the DAP is connected.
   Important: If you use several DAPs, which is to be assumed, you must set this VLAN to Tagged for all LAN ports of the switch to which the DAPs will be or are already connected!
   Click Apply.
   

8. The result:
   

9. Click on Save in the upper left corner and then on Save Configuration to save the settings permanently in the DGS-1210.

10. Click Save Config…
    … and then click OK.
    The configuration of the DGS-1210 is now complete. Now turn to the Nuclias Connect DNC-100/DNH-100.

The required settings in the DNC-100/DNH-100

These instructions assume that you are already using the DNC-100/DNH-100, or at least that you have already played through the setup wizard.

1. Go to the configuration of the DNC-100/DNH-100 and log in. Please leave the language or change it to English.
   

2. If the DAP access point is not yet mounted, do so now. Otherwise, continue to point 8 on page 10.
   On the left go to Configuration and then Create Profile. Then click on the magnifying glass to search for DAPs.![D-Link DNC-100 WLAN with Nuclias Connect

• DGS12](https://manuals.plus/wp-content/uploads/2023/05/D-Link-DNC-100-WLAN- with-Nuclias-Connect-DGS12.png)

  3. Click Next.
     

  4. Click Start Discovery.
     

  5. The DAP will be found. In this example a DAP-2660. Check the box in front of the DAP you found and click Apply.

  6. Task successfully sent appears. Please wait 15-20 seconds and then click Exit.

  7. On the left at Monitor -> Access Point , the integrated DAP is marked in green after a few minutes.
     

  8. Now create a second SSID for the guest Wi-Fi in addition to your main Wi-Fi.
     On the left select Configuration and then select Profile Settings.
     Go to SSID in your profile.
     Please DO NOT click on one of the primary WLANs.
     

  9. In the Security section at SSID, enter the SSID for the guest WLAN. In this example the guest Wi-Fi will be unencrypted and has no other authentication. Therefore let the Security as Open System.
     Click Add at the bottom right.
     

  10. The question appears if the setting should be applied to the other radio band. Click Yes.
      Note: If you click No, you must repeat step 9 for the other radio band (with a different SSID). ****

  11. In addition to the primary WLAN, the result is a SSID 1 for the guest WLAN:
      

  12. Now click on the VLAN menu on the left. At VLAN Status select Enabled and click Save. At VLAN 1 click the Edit icon under Action.
      

  13. Set SSID 1 to Not Member on all three radio bands. Click Save at the bottom-right.
      

  14. Select the Add/Edit VLAN tab on the top.
      At VLAN ID (VID) enter the same ID 10 this was previously used/added in the DGS-1210 and enter a VLAN name, e.g. Guest WLAN.

  15.  The management mgmt set you to Not Member. – LAN 1 and 2 remain/set on Tag.
      – Set SSID 1 of all three radio bands to Untag.
      – All others set to Not Member.
      Then click Add at the bottom-right.
      

  16. The result:
      

  17. Hint
      In a guest WLAN the clients should normally not be able to communicate with each other, they should be isolated from each other.
      To realize this, select the WLAN Partition menu on the left.
      Set Multi-SSID 1 to Guest Mode for 2,4 GHz and then click Save at the bottom- right. Do the same with the other Wi-Fi bands.
      

  18. Finally transfer the settings you have made into the DAP. On the left your profile is marked with yellow sign even when settings are made/changes in the DNH-100/DNC-100 profile but not yet transferred into the DAP.
      – Click on your profile.
      – Time Start is immediate.
      – Click Apply.
      After a few minutes the settings are active in the DAP.
      The setup of the Guest-WLAN in the DNH-100/DNC-100 is also complete.

Please note:
Is the DAP’s 5 GHz Wi-Fi running on a DFS channel (52-64 or 100-140)
it takes up to 5 minutes for the 5 GHz Wi-Fi to be available.

Very important:
Now connect the LAN port 4 of the Fritzbox to the LAN port 4 of the DGS-1210
Then you can then connect Wi-Fi clients to the guest Wi-Fi network of the DAP access points.
These obtain an IP address from the guest network of the Fritzbox and have Internet access via it. ****

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>