Vossloh Schwabe 187055 Blu2Light LAN Gateway Owner’s Manual
- June 10, 2024
- Vossloh Schwabe
Table of Contents
Vossloh Schwabe 187055 Blu2Light LAN Gateway
Safety notes
- The Blu2Light products may only be installed and commissioned by authorised specialists.
- Read these instructions carefully before installing and commissioning the system.
- This is the only way to ensure safe and correct handling.
- Keep this manual in a safe place so that it may be available at a later date.
- Before any work is carried out on the equipment, it must be disconnected from the supply voltage.
- The applicable safety and accident prevention regulations must be observed.
- Improper opening of the products is not permitted, there is a danger to life due to electrical voltage.
- Repairs may only be carried out by the manufacturer.
- If the device is connected permanently to the power network an all pole mains disconnect switch has to be used to disconnect the device from the power network. Protective earth (PE) must be connected.
Bluetooth® wireless technology
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Vossloh-Schwabe is under license. Other trademarks and trade names are those of their respective owners.
We, Vossloh-Schwabe Deutschland GmbH, herewith confirm that these devices comply with the basic requirements of the directive 2014/53/EU and other relevant directives. The entire text of the declaration of conformity can be obtained from the following address: www.vossloh-schwabe.com
Power supply
This product requires a power supply of 230 V AC. In addition, the product is wide voltage capable (100–240 V AC). A PoE (Power over Ethernet) supply is possible with this product.
Assembly
- Mounting only permissible in dry interior rooms
- Conductor cross-section on primary side 0.5–1.5 mm² for rigid or flexible cables
- Ambient temperature from 0–45 °C
- If the device is mounted on the wall or ceiling a smooth surface for mounting shall be considered. The used screws shall have a minimum of 8 mm in length.
Setup and operation
- The Blu2Light devices have to be configured with the LiNA Connect app.
- For the exact procedure for the configuration of the devices please refer to the instructions in the LiNA Connect app or in the corresponding documentation.
- An Apple iPad is required for setup, it is not included in the scope of delivery.
- For information on the iOS and Android operating systems that can currently be used, refer to the LiNA Connect/ LiNA Touch manual:
Important note:
Before installation, please also refer to the applicable device data sheet and
the Blu2Light system data sheet. Make sure that the Bluetooth radio signal can
propagate freely according to the specifications.
Technical Notes
Blu2Light LAN Gateway Ref. No.: 187055
- Communication: Blu2Light mesh network / Ethernet protocol (LAN)
- Frequency range: 2402–2480 MHz
- Power supply: 230 V AC
- Power consumption stand-by / operation: < 4 W Ambient temperature ta: 0–45 °C
- Degree of protection: IP20
- Protection class: II
- Dimensions (LxWxH): 195 x 102 x 38 mm
- Casing: Plastics, white
- Weight: 375 g
- Push-in terminals for lead cross section: 0.5–1.5 mm² (a different minimum conductor cross-section of 0,75 mm² in some countries has to be taken into account)
- PD: Powered devices
- PSE: Power sourcing equipment
Schaltplan / Wiring diagram
Standard
Daisy-Chain
PoE
SERVICE
Vossloh-Schwabe Deutschland GmbH
Stuttgarter Straße 61/1
D-73614 Schorndorf, Germany
Phone: +49 (0)7181 8002-0
info.vsv@vossloh-schwabe.com
For further information please visit our website: www.vossloh- schwabe.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>