ARADA BK 772 Garden Heater Instruction Manual
- June 10, 2024
- ARADA
Table of Contents
Garden Heater
Side Extending Shelves
Optional accessory fitting instructions
BK 772 Garden Heater
PLEASE RETAIN THIS GUIDE FOR FUTURE REFERENCE
BK 772 Rev 01
ISSUE DATE: 14/07/2022
Garden Heater Side Extending Shelves
Contents Of Kit :
Arada Part Code : ARA058
Warnings :
IMPORTANT— Please ensure the appliance is cold and unlit before commencing
fitting this accessory kit.
Observe safe working practices whilst installing or adjusting these
components.
Please refer to the main instruction booklet, relevant to your stove, for
guidance and operation of the appliance.
With the appliance in operation, these components will become hot during use.
Caution should be exercised in the present of children and elderly, together
with flammable or combustible materials, should not be used on these side
extending shelves.
Arada Ltd will not be responsible for any consequential or incidental loss or
injury however caused.
Assemble Of The Shelf
Step 1 : Take 1x side bracket and 1x extending shelf, position the side
bracket over the extending shelf, align the slotted holes in the bracket with
the round holes in the extended shelf.
See Fig. 1.
Step 2 : Taking 1x M6x16 HT set screw place this through one of the round
holes, with the thread through the slotted hole in the bracket. See Fig. 2.
The thread should be exposed outwards, where you can fix 1x M6 dome nut. Only
hand tighten this nut with a 10mm spanner, or damage will occur to the
bracket. See Fig.3. There will be a gap of approximately 3mm per side.
Step 3 : Repeat the other side of the bracket, with a further 1x M6x16 HT set
screw and 1x M6 dome nut.
Step 4 : Repeat steps 1 to 3 for the remaining extending shelf assembly.
Fitting The Extended Shelf Assembly To The Heater
Step 1: Ensure that your garden heater is cold and unlit.
Step 2: Open the fire door and working on the left hand side, locate the
2x side mount nuts, these are located towards the top of the side. Untighten
the 2x M8 nuts using a 13mm spanner. There is no need to remove the nut. See
Fig. 4.
Step 3: On the outside of the heater, you will notice that the circular
coach bolts will be loose, you will need approximately a 5mm gap, from the
body of the heater to the underside of the bolt head, to allow the extended
shelf side bracket to slot into place. See Fig. 2.
Fitting The Extended Shelf Assembly To The Heater Cont.
Step 4 : Next taking the extending shelf assembly, lower the side bracket over
the 2x protruding coach bolt heads (see Fig. 6). Engage the bracket behind the
head of each coach bolt and ensure the bracket drops onto the curved recess,
see close up Fig. 7.
Step 5 : Working on the inside of the firebox, re-tighten the 2x M8 nuts using
a 13mm spanner.
See Fig. 8.
Step 6 : Repeat the steps 1 to 5 for the opposite extending shelf.
Storage / Folding Of Extended Shelves
To fold the shelf, simply, take hold of the end of the shelf and lift up this end (See Fig. 9). Whilst doing this, gently pull the shelf away from the heater body, together with lowering the end towards the heater body, see Fig. 10. The bottom image (Fig. 11) shows the folded shelf in position.
Arada Ltd
The Fireworks, Weycroft Avenue, Axminster, Devon,EX13 5HU United Kingdom
www.aradastoves.com
www.aradastovesandspares.com Tel: +44
(0)1297 632 050
www.aradastoves.com
BK 772 Rev 01
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>