ARADA BK766 M Series 5 Widescreen Traditional Stoves User Guide

ARADA BK766 M Series 5 Widescreen Traditional Stoves User Guide

STEP 1 : Identify the issue with your stove

• Issue A: Small Gap Between Seal & Stove
  

• Issue B : Door Will NOT Latch Closed
  

• Issue C : Loose Door Pin
  

• Issue D: Jammed Open Roller Guides On Catch
  

STEP 2 : Adjustment steps and guide: Issue A

WARNING : ENSURE THAT THE APPLIANCE IS UNLIT & COLD
BEFORE ATTEMPTING ANY OF THE ENCLOSED INSTRUCTIONS

A visible gap between the door seal and the stove body.

This will require the door pin to be adjusted clockwise towards the body, resulting in moving the pin closer to the body face and therefore pulling to door towards the body of the stove, compressing the rope seal.

PLEASE NOTE: This rectified procedure differs from the original factory setup you may have present on your stove.

To correctly adjust the door please follow the following steps:

• Open the door

• In the inside of the firebox on the right hand side (BEHIND PIN) remove the lock nut, using a 10mm spanner , see Fig.1.
  

• Using a pair of pliers, unscrew the pin, using the flats built into the end of the pin. Withdraw the pin from the stove body , see Fig.2.
  

• You will notice on the pin there will be a brass nut, approximately half way down the threaded section of the pin. Take a ruler and measure the distance from the nut to the end of the threaded section of the pin, make a note of this dimension , see Fig.3.
  

• Screw the adjustment nut, towards the catch (pointed end) of the pin. With the lock nut, (removed
  in point 2 of the above), screw this onto the pin.

• This lock nut should be 1mm less than the dimension measure and noted above. Check with a ruler. Whilst holding this lock nut, screw the remaining adjustment nut to tighten against the lock nut, see Fig.4.
  

• Place the pin through the body opening, ensuring that the nuts are not disturbed. Tighten into body.

• Close the fire door and check for gaps in the rope seal, together with the door catch is holding the door closed.

• If a gap in the rope seal is still present, then repeat the above set of instructions. Except this time take a further 1mm from the noted measurement.

• If the door will not latch closed, then the pin is adjusted to close to the body of the stove, please see further sections in these instructions.

ADDENDUM SHEET—Continuation

STEP 2 : Adjustment steps and guide: Issue B

The fire door will not stay closed or latch on the catch.
This will require the door pin to be adjusted anti-clockwise away from the body, resulting in moving the pin away from the body face and therefore pushing the door away from the body of the stove, latching the pin into the catch rollers.

PLEASE NOTE: This rectified procedure differs from the original factory setup you may have present on your stove.

To correctly adjust the door, please follow the following steps:

• Open the door

• In the inside of the firebox on the right hand side (BEHIND PIN) remove the lock nut, using a 10mm spanner, see Fig.1.
  

• Using a pair of pliers, unscrew the pin, using the flats built into the end of the pin. Withdraw the pin from the stove body, see Fig.2.
  

• You will notice on the pin there will be a brass nut, approximately half way down the threaded section of the pin. Take a ruler and measure the distance from the nut to the end of the threaded section of the pin, make a note of this dimension, see Fig.3.
  

• Screw the adjustment nut, towards the catch (pointed end) of the pin. With the lock nut, (removed in point 2 of the above), screw this onto the pin.

• This lock nut should be 1mm increased from the dimension measure and noted above. Check with a ruler. Whilst holding this lock nut, screw the remaining adjustment nut to tighten against the lock nut, see Fig.4.
  

• Place the pin through the body opening, ensuring that the nuts are not disturbed. Tighten into body.

• Close the fire door and check for latching onto the roller catch. Also check for gaps in the rope seal all around the perimeter of the door.

• If the door will still not latch closed, then the pin will need further adjustment, say a further +1mm onto the noted measurements, moving the pin away from the body

• If a gap in the rope seal is still present, t, please see further section in these instructions.

• hen repeat the above set of instructions. Except this time take a further 1mm from the noted measurement.

• If the door will not latch closed, then the pin is adjusted to close to the body of the stove, please see further section in these instructions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>