ARADA Hoxton Log Store and Pedestal Instruction Manual
- June 3, 2024
- ARADA
Table of Contents
ARADA Hoxton Log Store and Pedestal
OPTIONAL LOG STORE & PEDESTAL FITTING INSTRUCTIONS
WARNING : Health and Safety
Please consult health and safety guidelines for advice on handling heavy and /
or large items.
When lifting the appliance we recommend you always obtain assistance when
handling.
Extreme Caution is advised, due to the top heavy nature of this appliance.
Appliance Preparation
Your stove is factory fitted with the integral standard foot assembly, however
if it is so desired, this can be removed and an optional log store or pedestal
stand can be fitted, so that the appliance height can be raised.
STEP 1:
To remove the factory fitted feet assembly, it is suggested that the canopy
assembly & associated hot plate surrounds, be removed to avoid damage.
Carefully lower the stove onto its rear, taking care not to damage the rear
air box and heat shield cover.
We recommend lowering the stove onto the base packing pallet, that it was
delivered upon (see upper image).
NOTE : This step is only necessary, when the direct air cover has been
fitted. If fitted, remove direct air cover (highlighted in blue) by following
steps 2&3.
STEP 2:
To remove the direct air cover, you will need to remove the wheeled castors
and 4x fixings as indicated below. The direct air cover can then simply be
with drawn.
Retain the castors and fixings in case of later use.
STEP 3:
With the stove safely resting on its back, also remove the 7x dome nuts as
indicated below.
LOG STORE Specific Fitting Instruction
STEP A: With the appliance resting upon its rear surface, position the
log store assembly, against the appliance base, together with aligning the
studs to the holes within the top of the log store. Affix the 6 off M8 dome
nuts.
NOTE: DO NOT add nut to the stud CLOSEST to the hinge, as this will foul
the hinge mechanism.
Do not use excessive force when hand tighten these fixings, otherwise damage
to the threads and studs, may occur.
STEP B:
Taking care, return the appliance to the upright position.
Extra caution will be needed, as the centre of gravity will have moved by
fitting the new log store accessory.
CAUTION :
TAKE CARE WHEN LIFTING UPRIGHT
PEDESTAL STAND Specific Fitting Instructions
To fit the pedestal stand, please follow steps 1 to 3.
STEP C:
With the appliance resting upon its rear surface (Step 1, page 2), position
the pedestal stand assembly, against the appliance base, together with
aligning the studs to the holes within the top of stand. Supplied with the
stand are 7 off black M8 dome nuts. Affix these to the stand, only hand
tighten these fixings, otherwise damage to the threads may occur.
NOTE: Use Black M8 Dome Nuts Supplied
STEP D:
Taking care, return the appliance to the upright position.
Extra caution will be needed, as the centre of gravity will have moved by
fitting the new pedestal stand accessory.
CAUTION :
TAKE CARE WHEN LIFTING UPRIGHT
IMPORTANT INSTALLATION INFORMATION
Stove Fixing Applicable To Both Log Store & Pedestal
WARNING!
It is strongly recommended that the appliance is securely fixed to the floor
or hearth, to prevent movement during the opening and closing operation of the
fire door and for stability of the assembly.
If excessive force is used when pulling or slamming the fire door, this can
result in the appliance moving and damaging the flue connection and
surrounding hearth surface.
When installing, secure fixing can be done by using the supplied fixing
brackets and fixings.
See below for guidance
Arada Ltd, The Fireworks, Weycroft Avenue, Axminster, Devon, United Kingdom,
EX13 5HU
Technical Help : +44 (0)1297 632052
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>