Knightsbridge TRLED22 LED Non-Corrosive Light Instruction Manual
- June 4, 2024
- Knightsbridge
Table of Contents
Knightsbridge TRLED22 LED Non-Corrosive Light
SAFETY
- This product must be installed in accordance with the latest edition of the IEE Wiring Regulations BS7671 and current Building Regulations.
- If in any doubt, consult a qualified electrician
- Please isolate mains prior to installation or maintenance
- Check the total load on the circuit including when this luminaire is fitted does not exceed the rating of the circuit cable, fuse or circuit breaker
- Please note the IP Ingress Protection rating of this product when deciding the location for installation
- This product is Class I and must be earthed.
- This product is IP65 rated.
INSTALLATION
Note
If this product is being used in conjunction with an external PIR or sensor,
please confirm with the manufacturer of the sensors that they are compatible
with LED luminaires.
- Provide power to the required point of installation.
- Suitable IP rated junction boxes should be used where required
- Using the mounting brackets as a template, mark the location for, and drill the fixing holes ensuring not to infringe with any gas/water pipes or electrical cables Fixing centres.
Secure the mounting brackets to the surface using suitable fixings not included. Unfasten the clips on either side of the fitting.
Remove gear tray from the baseplate by pinching the clips at two
locations
Feed the mains cable through the compression gland provided at the
end of the fitting.
Align the fitting with the mounting brackets and clip into place
Connect the luminaire to the mains supply ensuring the correct polarity is observed: L – Live brown., Earth (green/yellow), N – Neutral (blue)
- Tighten the compression gland ensuring a tight seal is made.
- Replace the gear tray and diffuser ensuring all clips are fastened securely.
- Switch on and check for correct operation.
WARNING
This product must be disconnected from the circuit if subjected to any high
voltage or insulation resistance testing. Irreparable damage will occur if
this instruction is not followed.
Information about TRLED22 LED Non-Corrosive Light
This product contains a light source of energy efficiency class C (TRLED14, TRLED25D, TRLED26D) / Class D (TRLED12 / TRLED15 / TRLED15D / TRLED16 / TRLED16D / TRLED22 / TRLED24 / TRLED25 / TRLED26) to Regulation (EU) No. 2019/2015. This product contains a non replaceable LED light source and a control gear which can be replaced by a professional
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not use aggressive cleaning products or solvents which may damage the product. Do not use any source of high-pressure washers to maintain or clean this luminaire. This product is non dimmable. This product should be dismantled for disposal when it reaches the end of its life. Please see website for dismantling instructions. This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where facilities exist.
WARRANTY
This product has a warranty of 5 years from date of purchase. Failure to
install this product in accordance with the current edition of the IEE Wiring
Regulations BS7671 improper use, or removal of the batch code will invalidate
the warranty. If this product should fail within its warranty period, it
should be returned to the place of purchase for a free of charge replacement.
ML Accessories does not accept responsibility for any installation costs
associated with the replacement product. Your statutory rights are not
affected. ML Accessories reserve the right to alter product specification
without prior notice.
FOR INTERNATIONAL CONTACT DETAILS SCAN QR
Documents / Resources
|
Knightsbridge TRLED22 LED Non-Corrosive
Light
[pdf] Instruction Manual
TRLED12, TRLED14, TRLED15, TRLED15D, TRLED16, TRLED16D, TRLED22 LED Non-
Corrosive Light, TRLED22, LED Non-Corrosive Light, Non-Corrosive Light, Light,
TRLED24, TRLED25, TRLED25D, TRLED26, TRLED26D
---|---