XTREMEPOWERUS 75026 Single Speed 2HP Spa Pump Owner’s Manual
- June 10, 2024
- XTREMEPOWERUS
Table of Contents
- XTREMEPOWERUS 75026 Single Speed 2HP Spa Pump
- Product Information
- Product Usage Instructions
- SAFTEY WARNING
- ASSEMBLY AND OPERATION
- Pipe Assembly
- MAINTENANCE
- Trouble Shooting Guide
- Performance curves
- ELECTRICAL INFORMATION
- Installation structure
- PARTS INFORMATION
- DISCLAIMER
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
XTREMEPOWERUS 75026 Single Speed 2HP Spa Pump
Product Information
The product is an electrical equipment used for pumping liquids. It is designed to be installed horizontally and secured with screws through the holes in the supports to prevent noise and vibration. The suction pipe of the pump should be as short as possible for efficient operation. The product comes with a rating label that should be visible after installation. Parts containing live parts, except parts supplied with safety extra-low voltage.
Product Usage Instructions
- Ensure that basic safety precautions are followed when installing and using the product.
- Install the pump horizontally and secure it with screws through the holes in the supports to prevent noise and vibration.
- Ensure that the suction pipe of the pump is as short as possible for efficient operation.
- Make sure the rating label is visible after installation.
- Do not touch any parts containing live parts, except parts supplied with safety extra-low voltage.
OWNER’S MANUAL AND SAFETY INSTRUCTIONS
SAVE THIS MANUAL. KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATION, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE
PRODUCT’S SERIAL NUMBER ON THE BACK OF THE MANUAL, OR THE MONTH AND VEAR OF
PURCHASE IF PRODUCT HAS NO SERIAL NUMBER.
FOR QUESTIONS, PLEASE CALL CUSTOMER SERVICE: 909.628.0880
SAFTEY WARNING
WARNING
Read all safety warnings and instructions. Failure to follow the warnings
and instructions may result in injury and/or property damage. Save all
warnings and instructions for future reference. The warning and safety
instructions in this manual are not meant to cover all possible conditions and
situations that may occur. Common sense, caution and care must be exercised
when operating or cleaning tools and equipment. Always contact your dealer,
distributor, service agent or manufacturer about problems or conditions you do
not understand before operating the product.
When installing and using this electrical equipment, basic safety precautions
should always be followed, including the following:
These instructions are for correct installation, and optimum performance of
the Bath pumps, so they should be read carefully. These are single-stage
centrifugal pumps designed to operate with compact hydro-massage equipment,
They are equipped with a total-emptying system to prevent the discharge of
residual liquid in each stopping. These units are designed to operate with
clean water at a maximum water temperature of 50°C. Built of top quality
materials, they are subjected to strict hydraulic and electrical controls and
are carefully verified. Correct installation is ensured by following these
instructions and those of the wiring diagram; otherwise, over loads may be
produced in the motor. We decline responsibility for any damage caused by not
following these instructions.
ASSEMBLY AND OPERATION
The pumps should be installed horizontally, securing them with screws through the holes in the supports to prevent undesirable noise and vibration. The suction, pipe of lhe pump should be as short as possible. The rating Label must be visible after installation. Parts containing live parts, except parts supplied with safety extra low voltage<12V, must be inaccessible to a person in the bath. Class I appliances must be permanently connected to fixed wiring. Part including electrical components except remote control devices must be located or fixed so that they cannot into bath.
Pipe Assembly
The suction and discharge pipes should have a diameter equal to or greater than that of the intake tapping of the pump. Avoid traps as, in addition to affecting efficiency, they impede total overall emptying. The suction and discharge pipes should not rest on the pump in any case. Seal all the connectors and unions well. Avoid any dripping on the motor, which would unfailingly damage it.
Electrical connection
The electrical install action should have a multiple separation system with
contacts opening at least 3mm. For continued protection against possible
electric shock this unit is to be mounted to the base in accordance with the
installation instructions. The protection of the system should be based on a
residual current device (RCD) with a rated tripping current not exceeding
30mA. The supply cable should comply with EMC standards (2).Single-phase
motors have built-in thermal protectory. When the pump run under abnormal
condition and caused the thermal protector to work, please cut off the pump
power if it is at the low speed (1450r/min) and plug in 1 minute later. If the
pump is at the high speed (2900r/min), it will start work again when the
thermal protector reset automatically as the motor temperature drops to a
certain degree. The diagrams in Fig. (1) correct electrical connection. The
electric connection must be carried out by qualified staff following strictly
the “UL 1563, UL 1081” standard. Be sure that the grounding connection is
correctly made. The grounding conductor shall not be smaller than
NO.12AWG(3.3mm2) Be sure that the equipotential connection between the bath
and the pump is correctly made. Wires serving as equipotential bonding
conductors shall have a cross sectional area between 2.5 and 6mm1 and shall be
equipped with the terminal suitable receptacle.
Controls Prior to Initial Start-up
Verify that the pump shaft turns freely.
Check that the mains voltage and frequency are according to the name plate.
The hydro-massage assembly should be equipped with a system to prevent the
pump from starting up if a minimum water level is not present. Check the
rotating direction of the motor, which should concur with that indicated on
the fan cover.
If the motor does not start up, try to locate the problem in the table of most
common faults and their possible solutions that is provided further on.
THE PUMP SHOULD NEVER OPERATE DRY
Start-up
Start electrically the pump only when the suction and discharge pipes are
connected to the corresponding inlets and outlets. Check that there is no
obstacle in the pipes. Apply voltage to the motor and suitably adjust the jets
to obtain the desired flow.
MAINTENANCE
Our pumps for hydro massage facilities do not require any special maintenance or programming If the um will bop idle for a loneroid of jape it is recommended to disassemble clean and, store it in a dry, well-ventilated place. If the supply cord is damaged, it must be replaced by the manufacturer or its Service agent or a similarly qualified person to a hazard. Pump can be automotive empty water after correct installation. hen the pump needs to clean (1) filling with water up to level position of bathtub’s nozzle, (2) operating -3mimute, (3) exhausting water of bathtub after engine stop.
Trouble Shooting Guide
Performance curves
ELECTRICAL INFORMATION
Installation circuit diagram
As the colours of the wires In the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
connection unit proceed as follows. The wire which is coloured green must be
connected to the terminal in the connection unit which Is marked with the
letter E or by the earth symbol @ or coloured green or green-and-yellow. Black
wire and White wire connected with power supply is low speed. Red wire and
White wire connected with power supply is high speed.
Installation structure
Model| Qmax
(L/min)
| Hmax
(m)
| Volts/Hz| Power(P1)| Amps
---|---|---|---|---|---
KW| HP
75026
| 800| 17| 220-240/60| 2.2| 3| 10.5
- liquid Temperature :O ~+ 50°C
- Storage temperature: < +65 “C
- Max. Working pressure:0.3MPa
PARTS INFORMATION
Ref.NO. | PART NO. | Description | QTY |
---|---|---|---|
1 | 47018037001 | Nut adaptor | 2 |
2 | 47018036001 | Adaptor | 2 |
3 | 5431031080 | O-Ring | 2 |
4 | 48860105080 | drain plug | 3 |
5 | 5432002080 | Gasket | 3 |
6 | 5214027000 | Screw | 8 |
7 | 47281007080 | Pump cover | 1 |
8 | 5431209080 | O-ring | 1 |
9 | 47281005080 | diffuser | 1 |
10 | 647281071000 | Impeller | 1 |
11 | 5028258000 | Seal assembly | 1 |
12 | 47281001080 | Pump housing | 1 |
13 | 5023431000 | 3HP motor | 1 |
DISCLAIMER
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE
IS QUALIFIED
TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
Record Product’s Serial Number Here: ____ _
Note: If product has no serial number, record month and year of purchase
instead.
Note: Some parts are listed and shown for illustration purposes only and
are not available individually as replacement parts.
The material in this manual is for 111format10nal purposes only. The
product(s) 11 describes are subject to change \\th out prior Nollie, due to
the manufacturer’s continuous development program. Xtreme Powerups makes no
representations or warranties with respect to this or with respect to the
products described herem Xtreme Power US shall not be liable for any dunages,
losses, costs or expenses, direct, 111direct or 111c1dent,1l, consequenllal or
special, Ansmg out of, or
related to the use of this material or the products described herein.
Questions, issues or missing parts?
Before returning to your retailer, our customer service team is here to help .
- Call Us: 909.628.0880
- Email Us: customer@xtremepowerusa.com
Hours of Operation: 9am
3pm PST Monday
Friday
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>