JIECANG 25SLE1130 Tubular Motor with Built-in Li-ion Battery User Manual

JIECANG 25SLE1130 Tubular Motor with Built-in Li-ion Battery

Product Info

The Tubular Motor comes with a built-in Li-ion battery and can be charged with a 5V/2A adapter. The product model is JCD-25-S-LE-11-30-DC Motor and has the following parameters:

• Tube Diameter: 25mm
• S: Standard Q: Quiet P: Performance
• LE: With built-in Li-ion battery
• Torque: 1.1 N.m
• Speed: 30 rpm

Caution!
Read the following instructions carefully before operating the Tubular Motor.

Product Instructions

Motorhead button (H) functions

the limits are set and motor is not in
sleep mode
Adding/Removing Controller| Hold for 2s Jog1 Flicker1| Operation needs to be done within 10s. Sleep mode, RF Control
Inactive
Direction Reverse| Hold for 10s Jog3 Flicker3| All settings saved after direction reversed
Reset| Hold for 16s Jog4 Flicker4| All settings deleted

Pairing Motor with Controller
There are two ways to pair the motor with a controller:

Way 1:

1. Power on, add a new controller H button OK H button x2s Jog x1
2. Press Prg Select channel within 10s Jog x2

Way 2:
Power on, add controller B via pre-existing controller A Press Prg on A Jog x1 Press Prg on A Jog x1 Press Stop on B OK Jog x2

Note: Pairing cannot be done under group channels or 0 channels.

Direction Reverse Correct

To reverse the direction:

• If the limits are not set, and the direction goes opposite: Fav & Stop x2s Jog x1
• If limits are set and direction goes opposite: Prg Jog x1 Up x1 Jog x1 OK Down x1 Jog x1

Note: Do reverse the direction when it goes opposite.

Upper &Lower Limits Setting

To set the upper and lower limits:

• Up or Down Fix upper point Up & Fav x2s Jog x2 Upper limit set
• Up or Down Fix lower point Down & Fav x2s Jog x2 Lower limit set

Note:
Upper & Lower limits cannot be set at the same point. Before limits set, the motor will run in one-touch mode by pressing Up or Down, hold Up or Down for 2s, motor runs in constant-touch mode. Once limits set, press Up or Down, motor runs in constant-touch mode.

One-touch/Constant-touch Mode

To switch between one-touch and constant-touch modes:

• Constant-touch ———–> One-touch Prg Jog x1 Stop Jog x1 Stop Jog x1 Same operation can toggle from one-touch to constant-touch mode.

Note: When the motor is in one-touch mode, hold Up or Down for more than 2s, it will run in constant-touch mode.

Setting and Cancelling Favorite Position

To set or cancel the favorite position:

• Up or Down Fix Fav. position Fav & Stop x2s Jog x2 Fav. position set Shade is at Fav. position Fav & Stop x2s Jog x1 Fav. position Cancel

Note: The Fav. position setting only can be done after the upper & lower limits are set.

Hotkey to the Fav. Position

To get to the favorite position quickly:

• Fast get to the Fav. point Fav

Note: The hotkey to the favorite position can only be used after setting the favorite position.

Adjusting Upper & Lower Limits

To adjust the upper and lower limits:

• Adjust Upper limit Up & Fav x6s Jog x1 OK Jog x2
• Adjust Lower limit Down & Fav x6s Jog x1 Up or Down Fix new upper limit Up & Fav x2s Down & Fav x2s Jog x1 Up or Down OK Jog x2

Note: The operation should be done within 4mins.

Adjusting Motor Speed

To adjust the motor speed:

• Speed increase Up Jog x1 Prg Jog x1 Stop Jog x1
• Speed decrease Down Jog x1

Note:
If the motor doesn’t jog, the max/min speed has already been reached. There are 3 speeds adjustable.

Introduction

Models & Parameters (for details about other parameters, see the product nameplate)

Instructions And Functions

Motor head button (H) functions

Functions| Operation| Jogging time| LED lamp

flickers

| Note
---|---|---|---|---
Control the UP/STOP/ DOWN of the Shade| Short press| /| /| Can only operate after the limits are set and motor is not in sleep mode
Adding/Removing Controller| Hold for 2s| Jog1| Flicker1| Operation needs be done within 10s

Sleep mode,

RF Control Inactive

|

Hold for 6s

|

Jog*2

|

Flicker*2

| Hold H button for 6s, jog twice to show the motor RF control is inactive; Hold H button for 2s, the RF control is active again
Direction Reverse| Hold for 10s| Jog3| Flicker3| All settings saved alter direction reversed
Reset| Hold for 16s| Jog4| Flicker4| All settings deleted

Pairing Motor with Controller

• Way 1: Power on, add a new controller
• Way 2: Power on, add controller B via pre-existing controller A

Note: Pairing can not be done under group channels or 0 channels.

Direction Reverse

Correct

If the limits are not set, and the direction goes opposite.

If limits are set and the direction goes opposite.

Note: Do reverse the direction when it goes opposite.

Upper & Lower Limits Setting

Note:

• Upper&Lower limits cannot be set at the same point.
• Before limits are set, the motor will run in one-touch mode by pressing Up or Down, holding Up or Down for 2s, motor runs in constant-touch mode.
• Once limits are set, press Up or Down, motor runs in constant-touch mode.

One-touch/Constant-touch Mode

The same operation can toggle from one-touch to constant-touch mode.

Note:
When the motor is in one-touch mode, hold it Up or Down for more than 2s, and it will run in constant-touch mode.

Setting and Cancelling Favorite Position

Hotkey to the Fav. Position

Note: The Fav. position setting only can be done after upper&lower limits are set.

Adjusting Upper & Lower Limits

Adjust Upper limit

Adjust Lower limit

Note: The operation should be done within 4mins.

Adjusting Motor Speed

Note:
If the motor doesn’t jog, the max/min speed has already been reached. There are 3 speeds adjustable.

Removing Controllers

Remove all controllers

Note:
All the settings are saved even the controllers removed (limits set are saved). Controller A/B are already paired to the motor.

Canceling Limits

Note:
It is forbidden to run the motor if installed in the shade without limits. Limits should be set immediately to protect the shade.

Check Motor Battery Level(for Bi-directional motor only)

Note:
The shade running to the lower limit indicates that the battery power is 100%. The shade running to the upper limit indicates that the battery power is 0%. For example, if the shade is closed at 70%, it means the remaining battery power is 70%.

Troubleshooting

Motor does not work

| 1.Controller not paired 2.Motor inactive 3.Low battery| 1. Add controller

2. Hold H button for 2s to activate motor 3.Charging

Motor stops suddenly

| 1. Upper & Lower limit set incorrectly

2. Shade exceed rated load 3.Low battery

| 1.Re-set Upper & Lower limits 2.Adjust load

3.Charging

LED flickers 8 times on motor head when motor starts| Low battery| Charging

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>