JIECANG JCHR35W1BL2B 6-Channel LCD Remote Controller with Timer Instruction Manual
- June 6, 2024
- JIECANG
Table of Contents
JCHR35W1B/2B
6-Channel LCD Remote Controller with Timer
Instruction Manual
Product Info
a. Front
b. Back
02 Models & Parameters **(more info please refer to the nameplate)**
| Electrical Specification | Standard |
|---|---|
| Battery Type | Hand-held:CR24503V1 |
| Working Temperature | —10°C–50°C |
| Radio Frequency | 433.92M ± 100KHz |
| Transmit Distance | >=30m indoor |
Caution!
- The transmitter should not be exposed to moisture or impact, so as not to affect its life
- During use, when the remote control distance is significantly shorter or less sensitive, please check whether the battery needs to be replaced.
- When the battery voltage is too low, the LCD screen will show a low voltage prompt, prompting to replace the battery.
- Please properly dispose of used batteries according to the local garbage classification and recycling policy
Instruction
a. Channels & Groups Toggling
Note: Channel 0 is pre-set control of All Groups within the multi-
channel controller. Channels in groups can be set accordingly.
b. Number of Channels Setting
Note: Max&Min number is 6&1 when it’s set under channel 1-6.
c.Number of Groups Setting
Note: Max&Min number is 6&1 when it’s set under channel 0.
d.Channel in Group Setting
Note: Channel in groups setting is under GROUP 1-6.
e.Check the channels in groups
f. Prohibit dual-key operation
2. Repeat the above, dual-key operation activated
Note: When dual-key operation prohibited, these programming setting functions
are not allowed.
g. Position percent setting
Note: All the shades under same group will run to same position after percent setting.
h. Modes Toggling 
Manual: Without timer function
Timer: With timer control, maximum can set 20sets of data
Random: With random timing function, ±15 minutes on basis timing
i. Local time setting
j. Timer control
Note:
- Press Up&Stop, LCD shown CLOO, means current data cleared
- Press Down&Stop, LCD shown CL01, means first data set copied to current set
2. Timer setting
k. For other operations, pls refer to the motor operation instruction
Caution!
This device complies with Part 15 of the FCC. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Headquarter: Xinchang
ADD: No. 2 Laisheng Road, Provincial High-tech industrial Park, Xinchang
county,Zhejiang Province
EMAIL : jc35@jiecang.com
TEL : +86-575-86297980
FAX : +86-575-86297960
Documents / Resources
|
JIECANG JCHR35W1BL2B 6-Channel LCD Remote Controller with
Timer
[pdf] Instruction Manual
JCHR35W2B, 2ANKDJCHR35W2B, JCHR35W1B, 2ANKDJCHR35W1B, JCHR35W1BL2B, 6-Channel
LCD Remote Controller with Timer
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>