Zhejiang Jiecang Linear Motion Technology JCP35WA-A Long Distance Wireless Charger User Manual

June 6, 2024
Zhejiang Jiecang Linear Motion Technology

JCP35WA-A Long Distance Wireless Charger

Long Distance Wireless Charger
JCP35WA-A

Output USBC Red/Green indicator light Output USBA
Installation Surface
DC Input (DC5.5*2.1)

Model: Voltage Range: Rated Voltage/Current: Input Plug type: Output Plug type: Output TypeA+TypeC: Wireless Charge Distance: Standby Power Consumption: Efficiency: work Temperature: Protection Character:

JCP35WA-A DC22V-40V DC24V/1.5A
DC5.5*2.1 TYPEA+TYPEC
MAX 5V2A 13mm-28mm
1W >50% @25mm5W Load24V Input
0-35 Input Coil OCP,OTP,OVP,UVLO,FOD

125 20

125

2- 5

Installation Direction

ST4.2*16

13~28mm

13~28mm

The Packing Include:

Wireless Charging Power Station

X1

User Marnual

X1

Table Stick(optionally available)

X1

Installation screw pack

X1

Charge Status Indicator

Charger Status

Power On

Standby

Charging

Fault

Red LED

ON

ON

OFF

OFF

Green LED

Blink(1Hz) 1 time

OFF

ON

Blink(1Hz)

Note Abnormal conditions include: the receiving end is placed too far, the PCBA temperature is too high, metal foreign objects enter, the input current is overcurrent, and the input voltage is overvoltage, etc.

Certification

Avoid placing any metal on the heating surface during working. Avoid placing magnetic stripe card on the heating surface which can easily damage the card. Make sure that the thickness of the upper desktop is within the range of the specification, otherwise it will not be able to charge. Make sure that the table stick must be affixed directly above the Wireless Charger. Avoid humidity, liquid, fire and high temperature as it may cause hazard to users. Do not try to disassemble or modify the product. Do not attempt to disassemble to avoid fire hazard or short circuit. Any of damage by abnormal use of product will void the manuf acture warranty. Do not use product when the cord is damp, damaged or, loose as it may cause short circuitand overheat. Do not bend the power cord. Do not handle the power cord with wet hands or pull the built-in cable. Contact with overheated equipment may cause discoloration or surface damage. Keep to other electrical devices such as Microwaves, sufficient distance.

FCC Statement
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interfere received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouill est susceptible d’en compromettre le fonctionnement.
ISED RF exposure statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Le rayonnement de la classe b repecte ISED fixaient un environnement non contrôlés.Installation et mise en oeuvre de ce matériel devrait avec échangeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals