JIECANG JCHR35W5C2/C3 Remote Controller User Manual
- October 30, 2023
- JIECANG
Table of Contents
JCHR35W5C2/C3 Remote Controller
Product Information
The JCHR35W5C2/C3 Remote Controller is a 16-channel LCD remote controller used for controlling motorized shades. The remote controller has two models, JCHR35W5C2 and JCHR35W5C3, both of which have the same number of channels and LCD display. The remote controller features three favorite positions, where the user can save their preferred shade positions at 25%, 50%, and 75%.
Models & Parameters
The specific parameters for each model can be found on the nameplate of the
product.
Caution!
The transmitter should not be exposed to moisture or impact, so as not to
affect its life. 2. During use, when the remote control distance is
significantly shorter or less sensitive, please check whether the battery
needs to be replaced. 3. When the battery voltage is too low, the LED screen
will show a low voltage prompt, prompting to replace the battery. 4. Please
properly dispose of used batteries according to the local garbage
classification and recycling policy.
Product Usage Instructions
Channels & Groups Toggling
Note: Channel 0 is the group control for all the channels.
Number of Channels Setting
To set the number of channels, refer to the instructions for each model.
Number of Groups Setting
To set the number of groups, refer to the instructions for each model.
Channel in Group Setting
To add or remove a channel from a group, short press the button corresponding
to that channel. If the channel number is steady-lit, it is part of the group.
If the channel number is flashing, it is not part of the group.
Check the Channels in Groups
Refer to the instructions for each model to check which channels are in a
group.
Prohibit Dual-key Operation
To prohibit dual-key operation, refer to the instructions for each model.
Position Percent Setting
To set the shade position percentage, stop the shade at the desired percentage
and wait 3 seconds. The shade will move to the chosen percentage position.
Special operation on remote controller JCHR35W5C3:
- CH+ & Up: Upper limit set
- CH+ & Down: Lower limit set
- CH+ & Stop: Favorite position set
- Press the CH+ button for 2 seconds to fast get to the favorite position
For all other operations, refer to the motor operation instruction manual.
Product Info
front view
Back view
Models & Parameters
(more info please refer to the nameplate)
Caution!
- The transmitter should not be exposed to moisture or impact, so as not to affect its life
- During use, when the remote control distance is significantly shorter or less sensitive, please check whether the battery needs to be replaced.
- When the battery voltage is too low, the LED screen will show a low voltage prompt, prompting to replace the battery.
- Please properly dispose of used batteries according to the local garbage classification and recycling policy.
Instructions
Channels & Groups Toggling
Note :Channel 0 is the group control for all the channels.
Number of Channels Setting Note : Max&Min number is 16&1 when it’s set under channel 1-16.
Number of Groups Setting Note : Max&Min number is 6&0 when it’s set under channel 0.
Channel in Group Setting Note : Channel in groups setting is under GROUP 1-6.
Check the Channels in Groups Note : LCD will show “EC” if there is no detailed channel.
Prohibit Dual-key Operation Repeat the above, dual-key operation
activated
Note: When dual-key operation prohibited, these programming setting functions
are not allowed, such as limits setting.
Position Percent Setting Note : All the shades under same group will run to same position after percent setting.
Special operation on remote controller JCHR35W5C3:
- CH+ & Up: Upper limit set
- CH+ & Down: Lower limit set
- CH+ & Stop: Favorite position set
- Press the “CH+” button for 2s to fast get to the Fav. point
i. For other operations, please refer to the motor operation instruction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>