ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO LTD JCHR35W7A Hand-Held Remote with Vane Adjustment User Manual
- June 4, 2024
- ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO LTD
Table of Contents
ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO LTD JCHR35W7A Hand-Held
Remote with Vane Adjustment
Product Information
- Specifications
- Model: JCHR35W7A
- Type: Hand-held Remote
- Channels: 6
- Vane Adjustment: Yes
- Number of Channels Setting
- Make sure the remote is powered on and within range of the device you wish to control.
- Use the channel buttons to select the desired channel for operation.
FAQs
- What should I do if the remote is not responding?
- If the remote is not responding, try replacing the batteries.
- Ensure that there are no obstructions between the remote and the device being controlled.
- How do I adjust the vanes using the remote?
- To adjust the vanes using the remote, select the appropriate channel and use the vane adjustment buttons to control the position of the vanes.
Product Info
JCHR35W7A Hand-held 6-channel remote with vane adjustment
Buttons
- a. Front
- JCHR35W7A Hand-held 6-channel remote with vane adjustment
- b. Back
- JCHR35W7A Hand-held 6-channel remote with vane adjustment
Parameters
Parameters (For more info please refer to the nameplate)
- Electrical Specification Standard
- Battery Type AAA battery*2
- Working Temperature -10°C-50°C
- Radio Frequency 433.9MHz
- Transmit Distance >=30m indoor
Caution!
- The transmitter should not be exposed to moisture or impact, so as not to affect its life
- During use, when the remote control distance is significantly shorter or less sensitive, please check whether the battery needs to be replaced.
- When the battery voltage is too low, an orange LED flickers when you press the button, indicating to replace the battery.
- Pls properly dispose of used batteries according to the local garbage classification and recycling policy.
Instructions
- a. Child-lock (Prohibit dual-key operation)
1. Dual-key operation prohibited
2. Repeat above step, dual-key operation activated
* **Note:** When dual-key operation is prohibited, these programming setting functions are not allowed: such as limits setting.- b. Number of Channels Setting
- Note: When all LEDs are lit, that is channel 0 (All channels move together ).
- c. Vane Adjustment
- Scroll 1 notch: vanes go up or down 1 notch, lighting and heating changed per variator notch
- Scroll n notches: raise or lower the vanes by n steps, and vary the lighting and heating by n steps.
- d. For other operations, pls refer to the motor operation instruction
FCC
FCC Statement
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
RF warning for Portable devices:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Note: This equipment has been tested and found to comply with the limits for Class B digital devices, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>