ADA K600-RGB LED Lighting System User Manual

ADA K600-RGB LED Lighting System

SAFETY CAUTION

• Be cautious not to drop this product into water or off the ground.
• Keep the Lighting Unit, control unit, AC adapter, and Power Supply Plug away from water. This product is not waterproof.
• Water running down the power plug can cause fire or electric shock. In case of using an electrical outlet located below the aquarium, it’s recommended to use Power Cord S-70 (optional) to keep the electrical outlet away from water.
• Do NOT leave the Lighting Unit directly on the floor or any places other than an aquarium tank during use.
• Do NOT use this product with a dimmer. Dimming must be performed via the application.
• The lighting unit becomes hot due to heat radiation during use. It is not a malfunction of the product.
• The lighting unit, control unit, and AC adapter become very hot during lighting period and will remain hot for a while after the light turns off. Wait until they cool off before handling them. Never touch the top surface (radiation fin) and ballast of the lighting unit until they cool down, since they can become extremely hot.
• LED light of the lighting unit is not replaceable.
• Do NOT use any kind of adhesion tape on this product nor expose the product to direct sunlight. It can cause discoloration or deterioration of the product.
• Do NOT use this product in a place with poor electrical connections. It may cause flickering light or black out.
• Do NOT use this product near a radio or television. It can cause noise problems.
• Do NOT pull the Power Supply Cord while unplugging this product. Always hold AC adapter or Power Plug when plugging it off.
• Always unplug the Power Plug before maintenance.
• Do not attempt to disassemble or modify the product. If the product is serviced by another company or if a modification is made to the product, ADA will not accept the product for repair.
• The supplied Power Supply Cord is designed exclusively for the AC adapter of this product. Do not use any power cord other than the supplied Power Supply Cord for the AC adapter of this product. Use of any power cord other than the supplied cord may cause damage to the product. Do not use the supplied Power Supply Cord with anything other than this product.
• The illumination intensity of this product can be adjusted using the dedicated application. Continued illumination at the maximum illuminance may reduce the durability of the components.

Product Features

Product Features of AQUASKY RGB Ⅱ 60
AQUASKY RGBⅡ60 is a LED lighting system for aquatic plants with special RGB LED chips adopted to the light source. In the initial mode, because each wavelength output of the three primary colors of light, such as red (R), green (G) and blue (B) is optimized for planted aquariums, healthy aquatic plants grow, and it enables to achieve colorful and beautiful aquascapes. In addition, various controls, such as dimming and timer settings, can be performed by using ADA Controller, the dedicated application. The newly adopted soft lighting mode allows gentle control of not only lights on but also lights off.

Compatible Aquarium Tank:

• Cube Garden W60×D30×H36 (cm) Glass thickness 6mm
• Cube Garden W60 x D30 x H25 (cm) Glass thickness 5mm
• Cube Garden W60 x D30 x H36 (cm) Glass thickness 6mm
• Cube Garden W60 x D30 x H45 (cm) Glass thickness 6mm
• Cube Garden W60 x D45 x H36 (cm) Glass thickness 6mm

The leg of the lighting unit is installed in a way that it hangs on the outside of the aquarium. Therefore, it can be installed to a W60 aquarium regardless of the thickness of the glass.

Names of Product Parts

Operating instruction

without the dedicated application

• Install the lighting unit on the corresponding Cube Garden as shown in the figure.
• Be cautious not to drop the unit into the water during installation.
• Connect the control unit and AC adapter to the Lighting Unit. Plug the AC adapter’s power plug into an electrical outlet and turn on the Power Supply Switch for lighting.

To turn off the light, switch off the Power Supply Switch.

with the ADA controller application

1. Download the ADA controller to your smartphone or tablet.
2. Connect the control unit and AC adapter to the lighting unit, and plug the AC adapter’s power plug into an outlet.
3. Open the ADA controller and connect.
4. Press the reset button for at least 5 seconds and then release it to return to the initial mode.

Installation diagram
(AQUASKY RGBⅡ 60)

Product Specification

• Input voltage AC100～240V　50／60Hz
• Rated Power 108W
• Power consumption 0 to 66W
• Illuminance 0 to 40,000Lux
• Color temperature Default setting mode approx. Around 9,000～12,000K (Due to the nature of LED lighting, there are variations in color temperature.)
• LED RGB LED × 70
• LED lifetime Over 30,000hrs (subject to the operating environment)
• Operating temperature range 0～35℃

FCC STATEMENT

CAUTION:
Changes or Modifications not expressly approved by the party responsible could void the user’s authority to operate this device.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>